[cali] new BOARD_EIS007/EIS010/EISM007/EISM008/EISM010/EISM011/EISM012/EISM013 calibration data.

https://www.notion.so/3-EIS-Controller-EIS-Controller-check-sum-5426fe5ccb024a9da73770bed559df65

simplelink/ble_sdk_2_02_02_25/src/boards/BOOSTXL_CC2650MA/BOOSTXL_CC2650MA.c

@@ -36,11 +36,10 @@
  *  CC2650 Booster Pack.
  */
 
+
 /*
  *  ====================== Includes ============================================
  */
-
-// clang-format off
 #include <xdc/std.h>
 #include <xdc/runtime/System.h>
 
@@ -57,46 +56,16 @@
 #include <inc/hw_ints.h>
 #include <driverlib/ioc.h>
 #include <driverlib/udma.h>
-// clang-format on
 
 #include "Board.h"
 
-///*
-// *  ========================= IO driver initialization =========================
-// *  From main, PIN_init(BoardGpioInitTable) should be called to setup safe
-// *  settings for this board.
-// *  When a pin is allocated and then de-allocated, it will revert to the state
-// *  configured in this table.
-// */
-//
-///* Place into subsections to allow the TI linker to remove items properly */
-//#if defined(__TI_COMPILER_VERSION__)
-//#pragma DATA_SECTION(BoardGpioInitTable, ".const:BoardGpioInitTable")
-//#pragma DATA_SECTION(PINCC26XX_hwAttrs, ".const:PINCC26XX_hwAttrs")
-//#endif
-//
-//PIN_Config BoardGpioInitTable[] = {                                           //
-//    PIN_MEM_INS | PIN_INPUT_EN | PIN_PULLUP | PIN_HYSTERESIS,
-//    PIN_MEM_REQ | PIN_INPUT_EN | PIN_PULLUP | PIN_HYSTERESIS,
-//    PIN_MEM_BZY | PIN_INPUT_EN | PIN_PULLUP | PIN_HYSTERESIS,
-//    PIN_MEM_SEL | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-//    PIN_MEM_TEST | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL | PIN_DRVSTR_MAX,
-//    PIN_TERMINATE};
-//
-//const PINCC26XX_HWAttrs PINCC26XX_hwAttrs = {
-//    //
-//    .intPriority = ~0,
-//    .swiPriority = 0
-//    //
-//};
-
 /*
  *  ========================= IO driver initialization =========================
  *  From main, PIN_init(BoardGpioInitTable) should be called to setup safe
  *  settings for this board.
  *  When a pin is allocated and then de-allocated, it will revert to the state
  *  configured in this table.
- */
+*/
 
 /* Place into subsections to allow the TI linker to remove items properly */
 #if defined(__TI_COMPILER_VERSION__)
@@ -104,22 +73,20 @@
 #pragma DATA_SECTION(PINCC26XX_hwAttrs, ".const:PINCC26XX_hwAttrs")
 #endif
 
-const PIN_Config BoardGpioInitTable[] = {                                           //
-    Board_RLED | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX, /* LED initially off             */
-    Board_GLED | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX, /* LED initially off             */
-    Board_UART_RX | PIN_INPUT_EN | PIN_PULLDOWN,                                    /* UART RX  */
-    Board_UART_TX | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL,              /* UART TX */
-    Board_SRDY | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL,                 /* SRDY */
-    Board_MRDY | PIN_INPUT_EN | PIN_PULLDOWN,                                       /* MRDY */
-    PIN_TERMINATE};
-
-const PINCC26XX_HWAttrs PINCC26XX_hwAttrs = {
-    //
-    .intPriority = ~0,
-    .swiPriority = 0
-    //
+const PIN_Config BoardGpioInitTable[] = {
+    Board_RLED   | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,         /* LED initially off             */
+    Board_GLED   | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,         /* LED initially off             */
+    Board_UART_RX | PIN_INPUT_EN | PIN_PULLDOWN,                                              /* UART RX  */
+    Board_UART_TX | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL,                        /* UART TX */
+   Board_SRDY | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL,                           /* SRDY */
+   Board_MRDY | PIN_INPUT_EN | PIN_PULLDOWN,                                                 /* MRDY */
+    PIN_TERMINATE
 };
 
+const PINCC26XX_HWAttrs PINCC26XX_hwAttrs = {
+    .intPriority = ~0,
+    .swiPriority = 0
+};
 /*============================================================================*/
 
 /*
@@ -129,14 +96,13 @@ const PINCC26XX_HWAttrs PINCC26XX_hwAttrs = {
 #if defined(__TI_COMPILER_VERSION__)
 #pragma DATA_SECTION(PowerCC26XX_config, ".const:PowerCC26XX_config")
 #endif
-
 const PowerCC26XX_Config PowerCC26XX_config = {
-    .policyInitFxn     = NULL,
-    .policyFxn         = &PowerCC26XX_standbyPolicy,
-    .calibrateFxn      = &PowerCC26XX_calibrate,
-    .enablePolicy      = TRUE,
-    .calibrateRCOSC_LF = TRUE,
-    .calibrateRCOSC_HF = TRUE,
+    .policyInitFxn      = NULL,
+    .policyFxn          = &PowerCC26XX_standbyPolicy,
+    .calibrateFxn       = &PowerCC26XX_calibrate,
+    .enablePolicy       = TRUE,
+    .calibrateRCOSC_LF  = TRUE,
+    .calibrateRCOSC_HF  = TRUE,
 };
 /*
  *  ============================= Power end ====================================
@@ -160,32 +126,28 @@ UARTCC26XX_Object uartCC26XXObjects[BOOSTXL_CC2650MA_UARTCOUNT];
 
 /* UART hardware parameter structure, also used to assign UART pins */
 const UARTCC26XX_HWAttrsV2 uartCC26XXHWAttrs[BOOSTXL_CC2650MA_UARTCOUNT] = {
-    //
     {
-        .baseAddr    = UART0_BASE,
-        .powerMngrId = PowerCC26XX_PERIPH_UART0,
-        .intNum      = INT_UART0_COMB,
-        .intPriority = ~0,
-        .swiPriority = 0,
-        .txPin       = Board_UART_TX,
-        .rxPin       = Board_UART_RX,
-        .ctsPin      = PIN_UNASSIGNED,
-        .rtsPin      = PIN_UNASSIGNED
-        //
+        .baseAddr       = UART0_BASE,
+        .powerMngrId    = PowerCC26XX_PERIPH_UART0,
+        .intNum         = INT_UART0_COMB,
+        .intPriority    = ~0,
+        .swiPriority    = 0,
+        .txPin          = Board_UART_TX,
+        .rxPin          = Board_UART_RX,
+        .ctsPin         = PIN_UNASSIGNED,
+        .rtsPin         = PIN_UNASSIGNED
     }
-    //
 };
 
 /* UART configuration structure */
-const UART_Config UART_config[] = {  //
+const UART_Config UART_config[] = {
     {
-        //
         .fxnTablePtr = &UARTCC26XX_fxnTable,
         .object      = &uartCC26XXObjects[0],
         .hwAttrs     = &uartCC26XXHWAttrs[0]
-        //
     },
-    {NULL, NULL, NULL}};
+    {NULL, NULL, NULL}
+};
 /*
  *  ============================= UART end =====================================
  */
@@ -207,27 +169,22 @@ UDMACC26XX_Object udmaObjects[BOOSTXL_CC2650MA_UDMACOUNT];
 
 /* UDMA configuration structure */
 const UDMACC26XX_HWAttrs udmaHWAttrs[BOOSTXL_CC2650MA_UDMACOUNT] = {
-    //
     {
-        //
         .baseAddr    = UDMA0_BASE,
         .powerMngrId = PowerCC26XX_PERIPH_UDMA,
         .intNum      = INT_DMA_ERR,
         .intPriority = ~0
-        //
     }
-    //
 };
 
 /* UDMA configuration structure */
-const UDMACC26XX_Config UDMACC26XX_config[] = {  //
+const UDMACC26XX_Config UDMACC26XX_config[] = {
     {
-        //
-        .object  = &udmaObjects[0],
-        .hwAttrs = &udmaHWAttrs[0]
-        //
+         .object  = &udmaObjects[0],
+         .hwAttrs = &udmaHWAttrs[0]
     },
-    {NULL, NULL}};
+    {NULL, NULL}
+};
 /*
  *  ============================= UDMA end =====================================
  */
@@ -249,64 +206,54 @@ SPICC26XXDMA_Object spiCC26XXDMAObjects[BOOSTXL_CC2650MA_SPICOUNT];
 
 /* SPI configuration structure, describing which pins are to be used */
 const SPICC26XXDMA_HWAttrsV1 spiCC26XXDMAHWAttrs[BOOSTXL_CC2650MA_SPICOUNT] = {
-    //
     {
-        //
-        .baseAddr          = SSI0_BASE,
-        .intNum            = INT_SSI0_COMB,
-        .intPriority       = ~0,
-        .swiPriority       = 0,
-        .powerMngrId       = PowerCC26XX_PERIPH_SSI0,
-        .defaultTxBufValue = 0,
-        .rxChannelBitMask  = 1 << UDMA_CHAN_SSI0_RX,
-        .txChannelBitMask  = 1 << UDMA_CHAN_SSI0_TX,
-        .mosiPin           = Board_SPI0_MOSI,
-        .misoPin           = Board_SPI0_MISO,
-        .clkPin            = Board_SPI0_CLK,
-        .csnPin            = PIN_UNASSIGNED
-        //
+        .baseAddr           = SSI0_BASE,
+        .intNum             = INT_SSI0_COMB,
+        .intPriority        = ~0,
+        .swiPriority        = 0,
+        .powerMngrId        = PowerCC26XX_PERIPH_SSI0,
+        .defaultTxBufValue  = 0,
+        .rxChannelBitMask   = 1<<UDMA_CHAN_SSI0_RX,
+        .txChannelBitMask   = 1<<UDMA_CHAN_SSI0_TX,
+        .mosiPin            = Board_SPI0_MOSI,
+        .misoPin            = Board_SPI0_MISO,
+        .clkPin             = Board_SPI0_CLK,
+        .csnPin             = Board_SPI0_CS
     },
-#ifdef HEADSTAGE_MA_USE_SPI2
     {
-        //
-        .baseAddr          = SSI1_BASE,
-        .intNum            = INT_SSI1_COMB,
-        .intPriority       = ~0,
-        .swiPriority       = 0,
-        .powerMngrId       = PowerCC26XX_PERIPH_SSI1,
-        .defaultTxBufValue = 0,
-        .rxChannelBitMask  = 1 << UDMA_CHAN_SSI1_RX,
-        .txChannelBitMask  = 1 << UDMA_CHAN_SSI1_TX,
-        .mosiPin           = Board_SPI1_MOSI,
-        .misoPin           = Board_SPI1_MISO,
-        .clkPin            = Board_SPI1_CLK,
-        .csnPin            = Board_SPI1_CS  //
-    },
-#endif
+        .baseAddr           = SSI1_BASE,
+        .intNum             = INT_SSI1_COMB,
+        .intPriority        = ~0,
+        .swiPriority        = 0,
+        .powerMngrId        = PowerCC26XX_PERIPH_SSI1,
+        .defaultTxBufValue  = 0,
+        .rxChannelBitMask   = 1<<UDMA_CHAN_SSI1_RX,
+        .txChannelBitMask   = 1<<UDMA_CHAN_SSI1_TX,
+        .mosiPin            = Board_SPI1_MOSI,
+        .misoPin            = Board_SPI1_MISO,
+        .clkPin             = Board_SPI1_CLK,
+        .csnPin             = Board_SPI1_CS
+    },  
 };
 
 /* SPI configuration structure */
-const SPI_Config SPI_config[] = {  //
+const SPI_Config SPI_config[] = {
     {
-        //
-        .fxnTablePtr = &SPICC26XXDMA_fxnTable,
-        .object      = &spiCC26XXDMAObjects[0],
-        .hwAttrs     = &spiCC26XXDMAHWAttrs[0]
-        //
+         .fxnTablePtr = &SPICC26XXDMA_fxnTable,
+         .object      = &spiCC26XXDMAObjects[0],
+         .hwAttrs     = &spiCC26XXDMAHWAttrs[0]
     },
-#ifdef HEADSTAGE_MA_USE_SPI2
     {
-        //
-        .fxnTablePtr = &SPICC26XXDMA_fxnTable,
-        .object      = &spiCC26XXDMAObjects[1],
-        .hwAttrs     = &spiCC26XXDMAHWAttrs[1]
-        //
+         .fxnTablePtr = &SPICC26XXDMA_fxnTable,
+         .object      = &spiCC26XXDMAObjects[1],
+         .hwAttrs     = &spiCC26XXDMAHWAttrs[1]
     },
-#endif
-    {NULL, NULL, NULL}};
+    {NULL, NULL, NULL}
+};
 /*
  *  ========================== SPI DMA end =====================================
- */
+*/
+
 
 /*
  *  ========================== Crypto begin ====================================
@@ -326,28 +273,28 @@ const SPI_Config SPI_config[] = {  //
 CryptoCC26XX_Object cryptoCC26XXObjects[BOOSTXL_CC2650MA_CRYPTOCOUNT];
 
 /* Crypto configuration structure, describing which pins are to be used */
-const CryptoCC26XX_HWAttrs cryptoCC26XXHWAttrs[BOOSTXL_CC2650MA_CRYPTOCOUNT] = {{
-    //
-    .baseAddr    = CRYPTO_BASE,
-    .powerMngrId = PowerCC26XX_PERIPH_CRYPTO,
-    .intNum      = INT_CRYPTO_RESULT_AVAIL_IRQ,
-    .intPriority = ~0,
-    //
-}};
+const CryptoCC26XX_HWAttrs cryptoCC26XXHWAttrs[BOOSTXL_CC2650MA_CRYPTOCOUNT] = {
+    {
+        .baseAddr       = CRYPTO_BASE,
+        .powerMngrId    = PowerCC26XX_PERIPH_CRYPTO,
+        .intNum         = INT_CRYPTO_RESULT_AVAIL_IRQ,
+        .intPriority    = ~0,
+    }
+};
 
 /* Crypto configuration structure */
-const CryptoCC26XX_Config CryptoCC26XX_config[] = {  //
+const CryptoCC26XX_Config CryptoCC26XX_config[] = {
     {
-        //
-        .object  = &cryptoCC26XXObjects[0],
-        .hwAttrs = &cryptoCC26XXHWAttrs[0]
-        //
+         .object  = &cryptoCC26XXObjects[0],
+         .hwAttrs = &cryptoCC26XXHWAttrs[0]
     },
-    {NULL, NULL}};
+    {NULL, NULL}
+};
 /*
  *  ========================== Crypto end ======================================
  */
 
+
 /*
  *  ========================= RF driver begin ==================================
  */
@@ -361,12 +308,10 @@ const CryptoCC26XX_Config CryptoCC26XX_config[] = {  //
 
 /* RF hwi and swi priority */
 const RFCC26XX_HWAttrs RFCC26XX_hwAttrs = {
-    //
     .hwiCpe0Priority = ~0,
     .hwiHwPriority   = ~0,
-    .swiCpe0Priority = 5,
-    .swiHwPriority   = 5,
-    //
+    .swiCpe0Priority =  5,
+    .swiHwPriority   =  5,
 };
 
 /*
@@ -389,21 +334,20 @@ const RFCC26XX_HWAttrs RFCC26XX_hwAttrs = {
 TRNGCC26XX_Object trngCC26XXObjects[BOOSTXL_CC2650MA_TRNGCOUNT];
 
 /* TRNG configuration structure, describing which pins are to be used */
-const TRNGCC26XX_HWAttrs TRNGCC26XXHWAttrs[BOOSTXL_CC2650MA_TRNGCOUNT] = {{
-    //
-    .powerMngrId = PowerCC26XX_PERIPH_TRNG,
-    //
-}};
+const TRNGCC26XX_HWAttrs TRNGCC26XXHWAttrs[BOOSTXL_CC2650MA_TRNGCOUNT] = {
+    {
+        .powerMngrId    = PowerCC26XX_PERIPH_TRNG,
+    }
+};
 
 /* TRNG configuration structure */
-const TRNGCC26XX_Config TRNGCC26XX_config[] = {  //
+const TRNGCC26XX_Config TRNGCC26XX_config[] = {
     {
-        //
-        .object  = &trngCC26XXObjects[0],
-        .hwAttrs = &TRNGCC26XXHWAttrs[0]
-        //
+         .object  = &trngCC26XXObjects[0],
+         .hwAttrs = &TRNGCC26XXHWAttrs[0]
     },
-    {NULL, NULL}};
+    {NULL, NULL}
+};
 
 /*
  *  ========================= TRNG end ====================================
@@ -421,62 +365,14 @@ const TRNGCC26XX_Config TRNGCC26XX_config[] = {  //
 
 /* GPTimer hardware attributes, one per timer part (Timer 0A, 0B, 1A, 1B..) */
 const GPTimerCC26XX_HWAttrs gptimerCC26xxHWAttrs[BOOSTXL_CC2650MA_GPTIMERPARTSCOUNT] = {
-    {
-        .baseAddr    = GPT0_BASE,
-        .intNum      = INT_GPT0A,
-        .intPriority = (~0),
-        .powerMngrId = PowerCC26XX_PERIPH_GPT0,
-        .pinMux      = GPT_PIN_0A,
-    },
-    {
-        .baseAddr    = GPT0_BASE,
-        .intNum      = INT_GPT0B,
-        .intPriority = (~0),
-        .powerMngrId = PowerCC26XX_PERIPH_GPT0,
-        .pinMux      = GPT_PIN_0B,
-    },
-    {
-        .baseAddr    = GPT1_BASE,
-        .intNum      = INT_GPT1A,
-        .intPriority = (~0),
-        .powerMngrId = PowerCC26XX_PERIPH_GPT1,
-        .pinMux      = GPT_PIN_1A,
-    },
-    {
-        .baseAddr    = GPT1_BASE,
-        .intNum      = INT_GPT1B,
-        .intPriority = (~0),
-        .powerMngrId = PowerCC26XX_PERIPH_GPT1,
-        .pinMux      = GPT_PIN_1B,
-    },
-    {
-        .baseAddr    = GPT2_BASE,
-        .intNum      = INT_GPT2A,
-        .intPriority = (~0),
-        .powerMngrId = PowerCC26XX_PERIPH_GPT2,
-        .pinMux      = GPT_PIN_2A,
-    },
-    {
-        .baseAddr    = GPT2_BASE,
-        .intNum      = INT_GPT2B,
-        .intPriority = (~0),
-        .powerMngrId = PowerCC26XX_PERIPH_GPT2,
-        .pinMux      = GPT_PIN_2B,
-    },
-    {
-        .baseAddr    = GPT3_BASE,
-        .intNum      = INT_GPT3A,
-        .intPriority = (~0),
-        .powerMngrId = PowerCC26XX_PERIPH_GPT3,
-        .pinMux      = GPT_PIN_3A,
-    },
-    {
-        .baseAddr    = GPT3_BASE,
-        .intNum      = INT_GPT3B,
-        .intPriority = (~0),
-        .powerMngrId = PowerCC26XX_PERIPH_GPT3,
-        .pinMux      = GPT_PIN_3B,
-    },
+    { .baseAddr = GPT0_BASE, .intNum = INT_GPT0A, .intPriority = (~0), .powerMngrId = PowerCC26XX_PERIPH_GPT0, .pinMux = GPT_PIN_0A, },
+    { .baseAddr = GPT0_BASE, .intNum = INT_GPT0B, .intPriority = (~0), .powerMngrId = PowerCC26XX_PERIPH_GPT0, .pinMux = GPT_PIN_0B, },
+    { .baseAddr = GPT1_BASE, .intNum = INT_GPT1A, .intPriority = (~0), .powerMngrId = PowerCC26XX_PERIPH_GPT1, .pinMux = GPT_PIN_1A, },
+    { .baseAddr = GPT1_BASE, .intNum = INT_GPT1B, .intPriority = (~0), .powerMngrId = PowerCC26XX_PERIPH_GPT1, .pinMux = GPT_PIN_1B, },
+    { .baseAddr = GPT2_BASE, .intNum = INT_GPT2A, .intPriority = (~0), .powerMngrId = PowerCC26XX_PERIPH_GPT2, .pinMux = GPT_PIN_2A, },
+    { .baseAddr = GPT2_BASE, .intNum = INT_GPT2B, .intPriority = (~0), .powerMngrId = PowerCC26XX_PERIPH_GPT2, .pinMux = GPT_PIN_2B, },
+    { .baseAddr = GPT3_BASE, .intNum = INT_GPT3A, .intPriority = (~0), .powerMngrId = PowerCC26XX_PERIPH_GPT3, .pinMux = GPT_PIN_3A, },
+    { .baseAddr = GPT3_BASE, .intNum = INT_GPT3B, .intPriority = (~0), .powerMngrId = PowerCC26XX_PERIPH_GPT3, .pinMux = GPT_PIN_3B, },
 };
 
 /*  GPTimer objects, one per full-width timer (A+B) (Timer 0, Timer 1..) */
@@ -484,15 +380,14 @@ GPTimerCC26XX_Object gptimerCC26XXObjects[BOOSTXL_CC2650MA_GPTIMERCOUNT];
 
 /* GPTimer configuration (used as GPTimer_Handle by driver and application) */
 const GPTimerCC26XX_Config GPTimerCC26XX_config[BOOSTXL_CC2650MA_GPTIMERPARTSCOUNT] = {
-    //
-    {&gptimerCC26XXObjects[0], &gptimerCC26xxHWAttrs[0], GPT_A},
-    {&gptimerCC26XXObjects[0], &gptimerCC26xxHWAttrs[1], GPT_B},
-    {&gptimerCC26XXObjects[1], &gptimerCC26xxHWAttrs[2], GPT_A},
-    {&gptimerCC26XXObjects[1], &gptimerCC26xxHWAttrs[3], GPT_B},
-    {&gptimerCC26XXObjects[2], &gptimerCC26xxHWAttrs[4], GPT_A},
-    {&gptimerCC26XXObjects[2], &gptimerCC26xxHWAttrs[5], GPT_B},
-    {&gptimerCC26XXObjects[3], &gptimerCC26xxHWAttrs[6], GPT_A},
-    {&gptimerCC26XXObjects[3], &gptimerCC26xxHWAttrs[7], GPT_B},
+    { &gptimerCC26XXObjects[0], &gptimerCC26xxHWAttrs[0], GPT_A },
+    { &gptimerCC26XXObjects[0], &gptimerCC26xxHWAttrs[1], GPT_B },
+    { &gptimerCC26XXObjects[1], &gptimerCC26xxHWAttrs[2], GPT_A },
+    { &gptimerCC26XXObjects[1], &gptimerCC26xxHWAttrs[3], GPT_B },
+    { &gptimerCC26XXObjects[2], &gptimerCC26xxHWAttrs[4], GPT_A },
+    { &gptimerCC26XXObjects[2], &gptimerCC26xxHWAttrs[5], GPT_B },
+    { &gptimerCC26XXObjects[3], &gptimerCC26xxHWAttrs[6], GPT_A },
+    { &gptimerCC26XXObjects[3], &gptimerCC26xxHWAttrs[7], GPT_B },
 };
 
 /*
@@ -510,15 +405,14 @@ const GPTimerCC26XX_Config GPTimerCC26XX_config[BOOSTXL_CC2650MA_GPTIMERPARTSCOU
 #endif
 /* PWM configuration, one per PWM output.   */
 PWMTimerCC26XX_HwAttrs pwmtimerCC26xxHWAttrs[BOOSTXL_CC2650MA_PWMCOUNT] = {
-    //
-    {.pwmPin = Board_PWMPIN0, .gpTimerUnit = Board_GPTIMER0A},
-    {.pwmPin = Board_PWMPIN1, .gpTimerUnit = Board_GPTIMER0B},
-    {.pwmPin = Board_PWMPIN2, .gpTimerUnit = Board_GPTIMER1A},
-    {.pwmPin = Board_PWMPIN3, .gpTimerUnit = Board_GPTIMER1B},
-    {.pwmPin = Board_PWMPIN4, .gpTimerUnit = Board_GPTIMER2A},
-    {.pwmPin = Board_PWMPIN5, .gpTimerUnit = Board_GPTIMER2B},
-    {.pwmPin = Board_PWMPIN6, .gpTimerUnit = Board_GPTIMER3A},
-    {.pwmPin = Board_PWMPIN7, .gpTimerUnit = Board_GPTIMER3B},
+    { .pwmPin = Board_PWMPIN0, .gpTimerUnit = Board_GPTIMER0A },
+    { .pwmPin = Board_PWMPIN1, .gpTimerUnit = Board_GPTIMER0B },
+    { .pwmPin = Board_PWMPIN2, .gpTimerUnit = Board_GPTIMER1A },
+    { .pwmPin = Board_PWMPIN3, .gpTimerUnit = Board_GPTIMER1B },
+    { .pwmPin = Board_PWMPIN4, .gpTimerUnit = Board_GPTIMER2A },
+    { .pwmPin = Board_PWMPIN5, .gpTimerUnit = Board_GPTIMER2B },
+    { .pwmPin = Board_PWMPIN6, .gpTimerUnit = Board_GPTIMER3A },
+    { .pwmPin = Board_PWMPIN7, .gpTimerUnit = Board_GPTIMER3B },
 };
 
 /* PWM object, one per PWM output */
@@ -528,16 +422,17 @@ extern const PWM_FxnTable PWMTimerCC26XX_fxnTable;
 
 /* PWM configuration (used as PWM_Handle by driver and application) */
 const PWM_Config PWM_config[BOOSTXL_CC2650MA_PWMCOUNT + 1] = {
-    //
-    {&PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[0], &pwmtimerCC26xxHWAttrs[0]},
-    {&PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[1], &pwmtimerCC26xxHWAttrs[1]},
-    {&PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[2], &pwmtimerCC26xxHWAttrs[2]},
-    {&PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[3], &pwmtimerCC26xxHWAttrs[3]},
-    {&PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[4], &pwmtimerCC26xxHWAttrs[4]},
-    {&PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[5], &pwmtimerCC26xxHWAttrs[5]},
-    {&PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[6], &pwmtimerCC26xxHWAttrs[6]},
-    {&PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[7], &pwmtimerCC26xxHWAttrs[7]},
-    {NULL, NULL, NULL}};
+    { &PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[0], &pwmtimerCC26xxHWAttrs[0] },
+    { &PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[1], &pwmtimerCC26xxHWAttrs[1] },
+    { &PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[2], &pwmtimerCC26xxHWAttrs[2] },
+    { &PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[3], &pwmtimerCC26xxHWAttrs[3] },
+    { &PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[4], &pwmtimerCC26xxHWAttrs[4] },
+    { &PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[5], &pwmtimerCC26xxHWAttrs[5] },
+    { &PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[6], &pwmtimerCC26xxHWAttrs[6] },
+    { &PWMTimerCC26XX_fxnTable, &pwmtimerCC26xxObjects[7], &pwmtimerCC26xxHWAttrs[7] },
+    { NULL,                NULL,                 NULL                 }
+};
+
 
 /*
  *  ============================= PWM end ======================================
@@ -545,13 +440,7 @@ const PWM_Config PWM_config[BOOSTXL_CC2650MA_PWMCOUNT + 1] = {
 
 /*
  *  ============================= I2C Begin=====================================
- */
-
-#ifdef  HEADSTAGE_LED_USE_I2C
-
-#define Board_I2C0_SCL0 IOID_10
-#define Board_I2C0_SDA0 IOID_11
-
+*/
 /* Place into subsections to allow the TI linker to remove items properly */
 #if defined(__TI_COMPILER_VERSION__)
 #pragma DATA_SECTION(I2C_config, ".const:I2C_config")
@@ -586,242 +475,6 @@ const I2C_Config I2C_config[] = {
     },
     {NULL, NULL, NULL}
 };
-#endif
 /*
  *  ========================== I2C end =========================================
  */
-
-/*
- *  ========================= Display begin ====================================
- */
-/* Place into subsections to allow the TI linker to remove items properly */
-#if defined(__TI_COMPILER_VERSION__)
-#pragma DATA_SECTION(Display_config, ".const:Display_config")
-#pragma DATA_SECTION(displaySharpHWattrs, ".const:displaySharpHWattrs")
-#pragma DATA_SECTION(displayUartHWAttrs, ".const:displayUartHWAttrs")
-#endif
-
-#include <ti/mw/display/Display.h>
-#include <ti/mw/display/DisplaySharp.h>
-#include <ti/mw/display/DisplayUart.h>
-
-/* Structures for UartPlain Blocking */
-DisplayUart_Object        displayUartObject;
-
-#ifndef BOARD_DISPLAY_UART_STRBUF_SIZE
-#define BOARD_DISPLAY_UART_STRBUF_SIZE    128
-#endif
-static char uartStringBuf[BOARD_DISPLAY_UART_STRBUF_SIZE];
-
-const DisplayUart_HWAttrs displayUartHWAttrs = {
-    .uartIdx      = Board_UART,
-    .baudRate     =     115200,
-    .mutexTimeout = BIOS_WAIT_FOREVER,
-    .strBuf = uartStringBuf,
-    .strBufLen = BOARD_DISPLAY_UART_STRBUF_SIZE,
-};
-
-/* Structures for SHARP */
-DisplaySharp_Object displaySharpObject;
-
-#ifndef BOARD_DISPLAY_SHARP_SIZE
-#define BOARD_DISPLAY_SHARP_SIZE    96 // 96->96x96 is the most common board, alternative is 128->128x128.
-#endif
-static uint8_t sharpDisplayBuf[BOARD_DISPLAY_SHARP_SIZE * BOARD_DISPLAY_SHARP_SIZE / 8];
-
-const DisplaySharp_HWAttrs displaySharpHWattrs = {
-    .spiIndex    = Board_SPI0,
-    .csPin       = Board_LCD_CS,
-    .extcominPin = Board_LCD_EXTCOMIN,
-    .powerPin    = Board_LCD_POWER,
-    .enablePin   = Board_LCD_ENABLE,
-    .pixelWidth  = BOARD_DISPLAY_SHARP_SIZE,
-    .pixelHeight = BOARD_DISPLAY_SHARP_SIZE,
-    .displayBuf  = sharpDisplayBuf,
-};
-
-/* Array of displays */
-const Display_Config Display_config[] = {
-#if !defined(BOARD_DISPLAY_EXCLUDE_UART)
-    {
-        .fxnTablePtr = &DisplayUart_fxnTable,
-        .object      = &displayUartObject,
-        .hwAttrs     = &displayUartHWAttrs,
-    },
-#endif
-#if !defined(BOARD_DISPLAY_EXCLUDE_LCD)
-    {
-        .fxnTablePtr = &DisplaySharp_fxnTable,
-        .object      = &displaySharpObject,
-        .hwAttrs     = &displaySharpHWattrs
-    },
-#endif
-    { NULL, NULL, NULL } // Terminator
-};
-
-/*
- *  ========================= Display end ======================================
- */
-
-
- /*
-  *  ============================= Watchdog begin =====================================
- */
-
- /* Place into subsections to allow the TI linker to remove items properly */
- #if defined(__TI_COMPILER_VERSION__)
- #pragma DATA_SECTION(Watchdog_config, ".const:Watchdog_config")
- #pragma DATA_SECTION(wdCC26XXHWAttrs, ".const:wdCC26XXHWAttrs")
- #endif
-
- #include <ti/drivers/watchdog/WatchdogCC26XX.h>
- WatchdogCC26XX_Object wdCC26XXObject[BOOSTXL_CC2650MA_WATCHDOGCOUNT];
-
- const WatchdogCC26XX_HWAttrs wdCC26XXHWAttrs[] = {
-    {
-     .baseAddr = WDT_BASE,
-     .intNum   = INT_WDT_IRQ,
-     .reloadValue = 100
-     }
- };
-
- /* I2S configuration structure */
- const Watchdog_Config Watchdog_config[] = {
-     {
-         .fxnTablePtr = &WatchdogCC26XX_fxnTable,
-         .object = &wdCC26XXObject[0],
-         .hwAttrs = &wdCC26XXHWAttrs[0]
-     },
-     {NULL, NULL, NULL}
- };
- /*
-  *  ============================= Watchdog end =====================================
- */
-
- /*
-  * ================================ ADC begin ======================================
-  */
-#ifdef HEADSTAGE_RECORD_BATTERY
-
-/* Place into subsections to allow the TI linker to remove items properly */
-#if defined(__TI_COMPILER_VERSION__)
-#pragma DATA_SECTION(ADC_config, ".const:ADC_config")
-#pragma DATA_SECTION(adcCC26xxHWAttrs, ".const:adcCC26xxHWAttrs")
-#endif
-
-#include <ti/drivers/ADC.h>
-#include <ti/drivers/adc/ADCCC26XX.h>
-
-/* ADC objects */
-ADCCC26XX_Object adcCC26xxObjects[BOOSTXL_CC2650MA_ADCCOUNT];
-
-const ADCCC26XX_HWAttrs adcCC26xxHWAttrs[BOOSTXL_CC2650MA_ADCCOUNT] = {
-    {
-        .adcDIO = Board_DIO0_ANALOG,
-        .adcCompBInput = ADC_COMPB_IN_AUXIO7,
-        .refSource = ADCCC26XX_FIXED_REFERENCE,
-        .samplingDuration = ADCCC26XX_SAMPLING_DURATION_2P7_US,
-        .inputScalingEnabled = true,
-        .triggerSource = ADCCC26XX_TRIGGER_MANUAL
-    },
-    {
-        .adcDIO = Board_DIO1_ANALOG,
-        .adcCompBInput = ADC_COMPB_IN_AUXIO6,
-        .refSource = ADCCC26XX_FIXED_REFERENCE,
-        .samplingDuration = ADCCC26XX_SAMPLING_DURATION_2P7_US,
-        .inputScalingEnabled = true,
-        .triggerSource = ADCCC26XX_TRIGGER_MANUAL
-    },
-    {
-        .adcDIO = Board_DIO2_ANALOG,
-        .adcCompBInput = ADC_COMPB_IN_AUXIO5,
-        .refSource = ADCCC26XX_FIXED_REFERENCE,
-        .samplingDuration = ADCCC26XX_SAMPLING_DURATION_2P7_US,
-        .inputScalingEnabled = true,
-        .triggerSource = ADCCC26XX_TRIGGER_MANUAL
-    },
-    {
-        .adcDIO = Board_DIO3_ANALOG,
-        .adcCompBInput = ADC_COMPB_IN_AUXIO4,
-        .refSource = ADCCC26XX_FIXED_REFERENCE,
-        .samplingDuration = ADCCC26XX_SAMPLING_DURATION_2P7_US,
-        .inputScalingEnabled = true,
-        .triggerSource = ADCCC26XX_TRIGGER_MANUAL
-    },
-    {
-        .adcDIO = Board_DIO4_ANALOG,
-        .adcCompBInput = ADC_COMPB_IN_AUXIO3,
-        .refSource = ADCCC26XX_FIXED_REFERENCE,
-        .samplingDuration = ADCCC26XX_SAMPLING_DURATION_2P7_US,
-        .inputScalingEnabled = true,
-        .triggerSource = ADCCC26XX_TRIGGER_MANUAL
-    },
-    {
-        .adcDIO = Board_DIO5_ANALOG,
-        .adcCompBInput = ADC_COMPB_IN_AUXIO2,
-        .refSource = ADCCC26XX_FIXED_REFERENCE,
-        .samplingDuration = ADCCC26XX_SAMPLING_DURATION_2P7_US,
-        .inputScalingEnabled = true,
-        .triggerSource = ADCCC26XX_TRIGGER_MANUAL
-    },
-    {
-        .adcDIO = Board_DIO6_ANALOG,
-        .adcCompBInput = ADC_COMPB_IN_AUXIO1,
-        .refSource = ADCCC26XX_FIXED_REFERENCE,
-        .samplingDuration = ADCCC26XX_SAMPLING_DURATION_2P7_US,
-        .inputScalingEnabled = true,
-        .triggerSource = ADCCC26XX_TRIGGER_MANUAL
-    },
-    {
-        .adcDIO = Board_DIO7_ANALOG,
-        .adcCompBInput = ADC_COMPB_IN_AUXIO0,
-        .refSource = ADCCC26XX_FIXED_REFERENCE,
-        .samplingDuration = ADCCC26XX_SAMPLING_DURATION_10P9_MS,
-        .inputScalingEnabled = true,
-        .triggerSource = ADCCC26XX_TRIGGER_MANUAL
-    },
-    {
-        .adcDIO = PIN_UNASSIGNED,
-        .adcCompBInput = ADC_COMPB_IN_DCOUPL,
-        .refSource = ADCCC26XX_FIXED_REFERENCE,
-        .samplingDuration = ADCCC26XX_SAMPLING_DURATION_2P7_US,
-        .inputScalingEnabled = true,
-        .triggerSource = ADCCC26XX_TRIGGER_MANUAL
-    },
-    {
-        .adcDIO = PIN_UNASSIGNED,
-        .adcCompBInput = ADC_COMPB_IN_VSS,
-        .refSource = ADCCC26XX_FIXED_REFERENCE,
-        .samplingDuration = ADCCC26XX_SAMPLING_DURATION_2P7_US,
-        .inputScalingEnabled = true,
-        .triggerSource = ADCCC26XX_TRIGGER_MANUAL
-    },
-    {
-        .adcDIO = PIN_UNASSIGNED,
-        .adcCompBInput = ADC_COMPB_IN_VDDS,
-        .refSource = ADCCC26XX_FIXED_REFERENCE,
-        .samplingDuration = ADCCC26XX_SAMPLING_DURATION_2P7_US,
-        .inputScalingEnabled = true,
-        .triggerSource = ADCCC26XX_TRIGGER_MANUAL
-    }
-};
-
-const ADC_Config ADC_config[] = {
-    {&ADCCC26XX_fxnTable, &adcCC26xxObjects[0], &adcCC26xxHWAttrs[0]},
-    {&ADCCC26XX_fxnTable, &adcCC26xxObjects[1], &adcCC26xxHWAttrs[1]},
-    {&ADCCC26XX_fxnTable, &adcCC26xxObjects[2], &adcCC26xxHWAttrs[2]},
-    {&ADCCC26XX_fxnTable, &adcCC26xxObjects[3], &adcCC26xxHWAttrs[3]},
-    {&ADCCC26XX_fxnTable, &adcCC26xxObjects[4], &adcCC26xxHWAttrs[4]},
-    {&ADCCC26XX_fxnTable, &adcCC26xxObjects[5], &adcCC26xxHWAttrs[5]},
-    {&ADCCC26XX_fxnTable, &adcCC26xxObjects[6], &adcCC26xxHWAttrs[6]},
-    {&ADCCC26XX_fxnTable, &adcCC26xxObjects[7], &adcCC26xxHWAttrs[7]},
-    {&ADCCC26XX_fxnTable, &adcCC26xxObjects[8], &adcCC26xxHWAttrs[8]},
-    {&ADCCC26XX_fxnTable, &adcCC26xxObjects[9], &adcCC26xxHWAttrs[9]},
-    {&ADCCC26XX_fxnTable, &adcCC26xxObjects[10], &adcCC26xxHWAttrs[10]},
-    {NULL, NULL, NULL},
-};
-
- /*
-  * ================================ ADC end ========================================
-  */
-#endif

simplelink/ble_sdk_2_02_02_25/src/boards/BOOSTXL_CC2650MA/BOOSTXL_CC2650MA.h

@@ -50,6 +50,7 @@ extern "C" {
  *  ==========================================================================*/
 #include <ti/drivers/PIN.h>
 #include <driverlib/ioc.h>
+#include "boards_config/elite_boards_select.h"
 
 /** ============================================================================
  *  Externs
@@ -89,25 +90,25 @@ extern const PIN_Config BoardGpioInitTable[];
 */
 
 /* Connector J1 */
-#define Board_BP_Pin_J1_2              IOID_UNUSED
-#define Board_BP_Pin_J1_3              IOID_UNUSED
-#define Board_BP_Pin_J1_4              IOID_UNUSED
-#define Board_BP_Pin_J1_5              IOID_UNUSED
-#define Board_BP_Pin_J1_6              IOID_UNUSED
-#define Board_BP_Pin_J1_7              IOID_UNUSED
-#define Board_BP_Pin_J1_8              IOID_UNUSED
-#define Board_BP_Pin_J1_9              IOID_UNUSED
-#define Board_BP_Pin_J1_10             IOID_UNUSED
+#define Board_BP_Pin_J1_2              DIO7
+#define Board_BP_Pin_J1_3              DIO0
+#define Board_BP_Pin_J1_4              DIO1
+#define Board_BP_Pin_J1_5              DIO2
+#define Board_BP_Pin_J1_6              DIO3
+#define Board_BP_Pin_J1_7              DIO10
+#define Board_BP_Pin_J1_8              DIO4
+#define Board_BP_Pin_J1_9              DIO5
+#define Board_BP_Pin_J1_10             DIO6
 
 /* Connector J2 */
-#define Board_BP_Pin_J2_19             IOID_UNUSED
-#define Board_BP_Pin_J2_18             IOID_UNUSED          /* CS */
-#define Board_BP_Pin_J2_17             IOID_UNUSED         /* NC */
-#define Board_BP_Pin_J2_15             IOID_UNUSED         /* MOSI */
-#define Board_BP_Pin_J2_14             IOID_UNUSED         /* MISO */
-#define Board_BP_Pin_J2_13             IOID_UNUSED
-#define Board_BP_Pin_J2_12             IOID_UNUSED
-#define Board_BP_Pin_J2_11             IOID_UNUSED          /* NC */
+#define Board_BP_Pin_J2_19             DIO8
+#define Board_BP_Pin_J2_18             DIO9          /* CS */
+#define Board_BP_Pin_J2_17             IOID_UNUSED   /* NC */
+#define Board_BP_Pin_J2_15             DIO11         /* MOSI */
+#define Board_BP_Pin_J2_14             DIO12         /* MISO */
+#define Board_BP_Pin_J2_13             DIO13
+#define Board_BP_Pin_J2_12             DIO14
+#define Board_BP_Pin_J2_11             IOID_UNUSED   /* NC */
 
 /* Mapping of BoosterPack Connector Pins to BoosterPack Standard Functions (reflecting the BoosterPack Standard)
 */
@@ -133,74 +134,27 @@ extern const PIN_Config BoardGpioInitTable[];
 #define Board_BP_SPI_CS_Other          Board_BP_Pin_J2_12
 #define Board_BP_GPIO_2                Board_BP_Pin_J2_11
 
+
 /* Mapping of application specific functionality of the BoosterPack to BoosterPack Pins (application dependent)
 */
 
-/* UART Board */
-#define Board_UART_TX                  DIO1          /* RXD */
-#define Board_UART_RX                  DIO0          /* TXD */
-
-/*
- *  interface with control box
- */
-#if defined(MODA_MEMORY_BOARD)
-#define Board_SPI0_MISO                DIO12
-#define Board_SPI0_MOSI                DIO11
-#define Board_SPI0_CLK                 DIO10
-#define Board_SPI_CS                   DIO9
-
-#define PIN_RAM_SEL                    DIO8        /* layout: MEM_SEL */
-#define PIN_MEM_SEL                    DIO4        /* layout: MEM_RST */
-#define PIN_MEM_BZY                    DIO13       /* layout: MEM_BZY */
-#define PIN_MEM_REQ                    DIO14       /* layout: MEM_REQ */
-#define PIN_MEM_TEST                   DIO7        /* layout: SPARE */
-
-/* On-board LEDs */
-#define Board_GLED                     PIN_UNASSIGNED                      /* Green LED */
-#define Board_RLED                     PIN_UNASSIGNED                      /* Red LED */
-
-#elif defined(MODA_BOOSTER_PACK)
-#define Board_SPI0_MISO                DIO7
-#define Board_SPI0_MOSI                DIO8
-#define Board_SPI0_CLK                 DIO9
-#define Board_SPI_CS                   DIO10
-
-#define PIN_MEM_INS                    DIO1
-#define PIN_MEM_SEL                    DIO2
-#define PIN_MEM_BZY                    DIO12
-#define PIN_MEM_REQ                    DIO0
-#define PIN_MEM_TEST                   DIO4
-
 /* On-board LEDs */
 #define Board_GLED                     DIO2                      /* Green LED */
 #define Board_RLED                     DIO4                      /* Red LED */
 
-#else
-#error "please define BOOSTXL_CC2650MA on BoosterPack or MemoryBoard"
-#endif
-//#define PIN_MEM_INS                    PIN_UNASSIGNED
-//#define PIN_MEM_BZY                    PIN_UNASSIGNED
-//#define PIN_MEM_REQ                    PIN_UNASSIGNED
-//#define PIN_MEM_SEL                    DIO4
-//#define PIN_MEM_TEST                   DIO2
+/* UART Board */
+#define Board_UART_TX                  Board_BP_UART_Rx          /* RXD */
+#define Board_UART_RX                  Board_BP_UART_Tx          /* TXD */
 
-/*
- *  unused SPI
- */
-
-#define Board_SPI1_MISO                PIN_UNASSIGNED
-#define Board_SPI1_MOSI                PIN_UNASSIGNED
-#define Board_SPI1_CLK                 PIN_UNASSIGNED
-#define Board_SPI1_CS                  PIN_UNASSIGNED
-
-#define Board_LCD_CS                   PIN_UNASSIGNED
-#define Board_LCD_EXTCOMIN             PIN_UNASSIGNED
-#define Board_LCD_POWER                PIN_UNASSIGNED
-#define Board_LCD_ENABLE               PIN_UNASSIGNED
+// /* SPI Board */
+// #define Board_SPI0_MISO                Board_BP_SPI_MISO
+// #define Board_SPI0_MOSI                Board_BP_SPI_MOSI
+// #define Board_SPI0_CLK                 Board_BP_SPI_CLK
+// #define Board_SPI0_CS                  Board_BP_SPI_CS_Wireless
 
 /* Power Management Board */
-#define Board_SRDY                     PIN_UNASSIGNED
-#define Board_MRDY                     PIN_UNASSIGNED
+#define Board_SRDY                     Board_BP_Pin_J2_19
+#define Board_MRDY                     Board_BP_Pin_J1_2
 
 /* PWM outputs */
 #define Board_PWMPIN0                  PIN_UNASSIGNED
@@ -212,24 +166,18 @@ extern const PIN_Config BoardGpioInitTable[];
 #define Board_PWMPIN6                  PIN_UNASSIGNED
 #define Board_PWMPIN7                  PIN_UNASSIGNED
 
-
 /** ============================================================================
  *  Instance identifiers
  *  ==========================================================================*/
-
 /* Generic SPI instance identifiers */
 #define Board_SPI0                  BOOSTXL_CC2650MA_SPI0
-
-#ifdef HEADSTAGE_MA_USE_SPI2
 #define Board_SPI1                  BOOSTXL_CC2650MA_SPI1
-#endif
-
+/* Generic I2C instance identifiers */
+#define Board_I2C0                  BOOSTXL_CC2650MA_I2C0
 /* Generic UART instance identifiers */
 #define Board_UART                  BOOSTXL_CC2650MA_UART0
-
 /* Generic TRNG instance identiifer */
 #define Board_TRNG                  BOOSTXL_CC2650MA_TRNG0
-
 /* Generic GPTimer instance identifiers */
 #define Board_GPTIMER0A             BOOSTXL_CC2650MA_GPTIMER0A
 #define Board_GPTIMER0B             BOOSTXL_CC2650MA_GPTIMER0B
@@ -239,17 +187,6 @@ extern const PIN_Config BoardGpioInitTable[];
 #define Board_GPTIMER2B             BOOSTXL_CC2650MA_GPTIMER2B
 #define Board_GPTIMER3A             BOOSTXL_CC2650MA_GPTIMER3A
 #define Board_GPTIMER3B             BOOSTXL_CC2650MA_GPTIMER3B
-
-/* Generic ADC instance identifiers */
-#define Board_DIO0_ANALOG           PIN_UNASSIGNED
-#define Board_DIO1_ANALOG           PIN_UNASSIGNED
-#define Board_DIO2_ANALOG           PIN_UNASSIGNED
-#define Board_DIO3_ANALOG           PIN_UNASSIGNED
-#define Board_DIO4_ANALOG           PIN_UNASSIGNED
-#define Board_DIO5_ANALOG           PIN_UNASSIGNED
-#define Board_DIO6_ANALOG           PIN_UNASSIGNED
-#define Board_DIO7_ANALOG           PIN_UNASSIGNED
-
 /* Generic PWM instance identifiers */
 #define Board_PWM0                  BOOSTXL_CC2650MA_PWM0
 #define Board_PWM1                  BOOSTXL_CC2650MA_PWM1
@@ -264,16 +201,6 @@ extern const PIN_Config BoardGpioInitTable[];
  *  Number of peripherals and their names
  *  ==========================================================================*/
 
-/*
- *  @def    BOOSTXL_CC2650MA_I2C
- *  @brief  Enum of I2C names on the cc2650 dev board
- */
-typedef enum BOOSTXL_CC2650MA_I2CName{
-    BOOSTXL_CC2650MA_I2C0   = 0,
-
-    BOOSTXL_CC2650MA_I2CCOUNT
-} BOOSTXL_CC2650MA_I2CName;
-
 /*!
  *  @def    BOOSTXL_CC2650MA_CryptoName
  *  @brief  Enum of Crypto names on the CC2650 Booster Pack
@@ -291,10 +218,7 @@ typedef enum BOOSTXL_CC2650MA_CryptoName {
  */
 typedef enum BOOSTXL_CC2650MA_SPIName {
     BOOSTXL_CC2650MA_SPI0 = 0,
-
-#ifdef HEADSTAGE_MA_USE_SPI2
-    BOOSTXL_CC2650MA_SPI1 ,
-#endif
+    BOOSTXL_CC2650MA_SPI1 = 1,
 
     BOOSTXL_CC2650MA_SPICOUNT
 } BOOSTXL_CC2650MA_SPIName;
@@ -375,34 +299,15 @@ typedef enum BOOSTXL_CC2650MA_PWM
     BOOSTXL_CC2650MA_PWMCOUNT
 } BOOSTXL_CC2650MA_PWM;
 
-typedef enum BOOSTXL_CC2650MA_WATCHDOG
-{
-    BOOSTXL_CC2650MA_WATCHDOG0 = 0,
-    BOOSTXL_CC2650MA_WATCHDOGCOUNT
-} BOOSTXL_CC2650MA_WATCHDOG;
-
-#ifdef HEADSTAGE_MA_USE_ADC
-
 /*!
- *  @def    BOOSTXL_CC2650MA_ADCName
- *  @brief  Enum of ADCs
+ *  @def    BOOSTXL_CC2650MA_I2CName
+ *  @brief  Enum of I2C names on the CC2650 Booster Pack
  */
-typedef enum BOOSTXL_CC2650MA_ADCName {
-    BOOSTXL_CC2650MA_ADC0 = 0,
-    BOOSTXL_CC2650MA_ADC1,
-    BOOSTXL_CC2650MA_ADC2,
-    BOOSTXL_CC2650MA_ADC3,
-    BOOSTXL_CC2650MA_ADC4,
-    BOOSTXL_CC2650MA_ADC5,
-    BOOSTXL_CC2650MA_ADC6,
-    BOOSTXL_CC2650MA_ADC7,
-    BOOSTXL_CC2650MA_ADCDCOUPL,
-    BOOSTXL_CC2650MA_ADCVSS,
-    BOOSTXL_CC2650MA_ADCVDDS,
-    BOOSTXL_CC2650MA_ADCCOUNT
-} BOOSTXL_CC2650MA_ADCName;
+typedef enum BOOSTXL_CC2650MA_I2CName {
+    BOOSTXL_CC2650MA_I2C0 = 0,
 
-#endif
+    BOOSTXL_CC2650MA_I2CCOUNT
+} BOOSTXL_CC2650MA_I2CName;
 
 #ifdef __cplusplus
 }

simplelink/ble_sdk_2_02_02_25/src/boards/BOOSTXL_CC2650MA/Board.h

@@ -60,6 +60,7 @@ extern "C" {
 #define     Board_initGPIO()
 #define     Board_initPWM()         PWM_init()
 #define     Board_initSPI()         SPI_init()
+#define     Board_initI2C()         I2C_init()
 #define     Board_initUART()        UART_init()
 #define     Board_initWatchdog()    Watchdog_init()
 #define     GPIO_toggle(n)

simplelink/ble_sdk_2_02_02_25/src/common/cc26xx/board_key.c

@@ -78,19 +78,16 @@ static void Board_keyCallback(PIN_Handle hPin, PIN_Id pinId);
 /*******************************************************************************
  * EXTERNAL VARIABLES
  */
-extern bool procedureInProgress;
+
 /*********************************************************************
  * LOCAL VARIABLES
  */
-PIN_State  keyPins;
-PIN_Handle hKeyPins;
 
 // Value of keys Pressed
-uint8_t keysPressed;
+static uint8_t keysPressed;
 
 // Key debounce clock
-Clock_Struct keyChangeClock;
-
+static Clock_Struct keyChangeClock;
 
 // Pointer to application callback
 keysPressedCB_t appKeyChangeHandler = NULL;
@@ -104,49 +101,18 @@ PIN_Config keyPinsCfg[] =
 #if defined (CC2650_LAUNCHXL) || defined (CC1350_LAUNCHXL)
     Board_BTN1          | PIN_GPIO_OUTPUT_DIS  | PIN_INPUT_EN  |  PIN_PULLUP,
     Board_BTN2          | PIN_GPIO_OUTPUT_DIS  | PIN_INPUT_EN  |  PIN_PULLUP,
-    Board_UART_RX_IRQ   | PIN_GPIO_OUTPUT_DIS  | PIN_INPUT_EN  |  PIN_PULLDOWN,
 #elif defined (CC2650DK_7ID)  || defined (CC1350DK_7XD)
     Board_KEY_SELECT    | PIN_GPIO_OUTPUT_DIS  | PIN_INPUT_EN  |  PIN_PULLUP,
     Board_KEY_UP        | PIN_GPIO_OUTPUT_DIS  | PIN_INPUT_EN  |  PIN_PULLUP,
     Board_KEY_DOWN      | PIN_GPIO_OUTPUT_DIS  | PIN_INPUT_EN  |  PIN_PULLUP,
     Board_KEY_LEFT      | PIN_GPIO_OUTPUT_DIS  | PIN_INPUT_EN  |  PIN_PULLUP,
     Board_KEY_RIGHT     | PIN_GPIO_OUTPUT_DIS  | PIN_INPUT_EN  |  PIN_PULLUP,
-#elif defined(BOOSTXL_CC2650MA)
-    PIN_MEM_SEL | PIN_GPIO_OUTPUT_DIS  | PIN_INPUT_EN | PIN_PULLUP,
-    PIN_MEM_REQ | PIN_GPIO_OUTPUT_DIS  | PIN_INPUT_EN | PIN_PULLUP,
-    PIN_MEM_BZY | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    PIN_RAM_SEL | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    Board_SPI_CS | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL,
-    PIN_MEM_TEST | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL,
-#if defined(MODA_BOOSTER_PACK)
-    Board_GLED | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    Board_RLED | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-#endif
-
 #endif
     PIN_TERMINATE
 };
 
-extern uint16_t EventMask;
-extern void ext_call_sem();
-
-/** event */
-#define EVT_ALL                  0xFFFF
-#define EVT_MEM_LED              0x0001  /**< set led event */
-#define EVT_MEM_LED_OFF          0x0002
-#define EVT_MEM_RETURN_DATA      0x0010
-#define EVT_MEM_NOTIFY_HANDLE    0x0040
-#define EVT_MEM_UART_ROUTINE     0x0080
-/**
- * fire a event with [flag].
- */
-#define flag_notify(flag)               \
-    do {                                \
-        uint8 __key = Hwi_disable();    \
-        EventMask |= (uint16_t)(flag);  \
-        Hwi_restore(__key);             \
-        ext_call_sem();                 \
-    } while (0)
+PIN_State  keyPins;
+PIN_Handle hKeyPins;
 
 /*********************************************************************
  * PUBLIC FUNCTIONS
@@ -162,21 +128,38 @@ extern void ext_call_sem();
  */
 void Board_initKeys(keysPressedCB_t appKeyCB)
 {
-    // Initialize KEY pins. Enable int after callback registered
-    hKeyPins = PIN_open(&keyPins, keyPinsCfg);
-    PIN_registerIntCb(hKeyPins, Board_keyCallback);
+  // Initialize KEY pins. Enable int after callback registered
+  hKeyPins = PIN_open(&keyPins, keyPinsCfg);
+  PIN_registerIntCb(hKeyPins, Board_keyCallback);
 
-#if defined (BOOSTXL_CC2650MA)
-    // PIN_setConfig(hKeyPins, PIN_BM_IRQ, PIN_MEM_SEL | PIN_IRQ_NEGEDGE);
-    PIN_setConfig(hKeyPins, PIN_BM_IRQ, PIN_MEM_REQ | PIN_IRQ_NEGEDGE);
-
-#elif defined (CC2650_LAUNCHXL) || defined (CC1350_LAUNCHXL)
-    PIN_setConfig(hKeyPins, PIN_BM_IRQ, Board_BTN1        | PIN_IRQ_NEGEDGE);
-    PIN_setConfig(hKeyPins, PIN_BM_IRQ, Board_BTN2        | PIN_IRQ_NEGEDGE);
+#if defined (CC2650_LAUNCHXL) || defined (CC1350_LAUNCHXL)
+  PIN_setConfig(hKeyPins, PIN_BM_IRQ, Board_BTN1        | PIN_IRQ_NEGEDGE);
+  PIN_setConfig(hKeyPins, PIN_BM_IRQ, Board_BTN2        | PIN_IRQ_NEGEDGE);
+#elif defined (CC2650DK_7ID)  || defined (CC1350DK_7XD)
+  PIN_setConfig(hKeyPins, PIN_BM_IRQ, Board_KEY_SELECT  | PIN_IRQ_NEGEDGE);
+  PIN_setConfig(hKeyPins, PIN_BM_IRQ, Board_KEY_UP      | PIN_IRQ_NEGEDGE);
+  PIN_setConfig(hKeyPins, PIN_BM_IRQ, Board_KEY_DOWN    | PIN_IRQ_NEGEDGE);
+  PIN_setConfig(hKeyPins, PIN_BM_IRQ, Board_KEY_LEFT    | PIN_IRQ_NEGEDGE);
+  PIN_setConfig(hKeyPins, PIN_BM_IRQ, Board_KEY_RIGHT   | PIN_IRQ_NEGEDGE);
 #endif
 
+#ifdef POWER_SAVING
+  //Enable wakeup
+#if defined (CC2650_LAUNCHXL) || defined (CC1350_LAUNCHXL)
+  PIN_setConfig(hKeyPins, PINCC26XX_BM_WAKEUP, Board_BTN1 | PINCC26XX_WAKEUP_NEGEDGE);
+  PIN_setConfig(hKeyPins, PINCC26XX_BM_WAKEUP, Board_BTN2 | PINCC26XX_WAKEUP_NEGEDGE);
+#elif defined (CC2650DK_7ID)  || defined (CC1350DK_7XD)
+  PIN_setConfig(hKeyPins, PINCC26XX_BM_WAKEUP, Board_KEY_SELECT | PINCC26XX_WAKEUP_NEGEDGE);
+  PIN_setConfig(hKeyPins, PINCC26XX_BM_WAKEUP, Board_KEY_UP | PINCC26XX_WAKEUP_NEGEDGE);
+  PIN_setConfig(hKeyPins, PINCC26XX_BM_WAKEUP, Board_KEY_DOWN | PINCC26XX_WAKEUP_NEGEDGE);
+  PIN_setConfig(hKeyPins, PINCC26XX_BM_WAKEUP, Board_KEY_LEFT | PINCC26XX_WAKEUP_NEGEDGE);
+  PIN_setConfig(hKeyPins, PINCC26XX_BM_WAKEUP, Board_KEY_RIGHT | PINCC26XX_WAKEUP_NEGEDGE);
+#endif
+#endif //POWER_SAVING
+
   // Setup keycallback for keys
-  Util_constructClock(&keyChangeClock, Board_keyChangeHandler, KEY_DEBOUNCE_TIMEOUT, 0, false, 0);
+  Util_constructClock(&keyChangeClock, Board_keyChangeHandler,
+                      KEY_DEBOUNCE_TIMEOUT, 0, false, 0);
 
   // Set the application callback
   appKeyChangeHandler = appKeyCB;
@@ -193,24 +176,47 @@ void Board_initKeys(keysPressedCB_t appKeyCB)
  */
 static void Board_keyCallback(PIN_Handle hPin, PIN_Id pinId)
 {
-    keysPressed = 0;
-#if defined (BOOSTXL_CC2650MA)
-//    if (PIN_getInputValue(PIN_MEM_REQ) == 0 && !procedureInProgress) {
-    //    keysPressed |= KEY_REQ;
-//        flag_notify(EVT_PIN_REQST);
-//    }
+  keysPressed = 0;
 
-#elif defined (CC2650_LAUNCHXL) || defined (CC1350_LAUNCHXL)
-    if (PIN_getInputValue(Board_BTN1) == 0) {
-        keysPressed |= KEY_LEFT;
-    }
+#if defined (CC2650_LAUNCHXL) || defined (CC1350_LAUNCHXL)
+  if ( PIN_getInputValue(Board_BTN1) == 0 )
+  {
+    keysPressed |= KEY_LEFT;
+  }
 
-    if (PIN_getInputValue(Board_BTN2) == 0) {
-        keysPressed |= KEY_RIGHT;
-    }
+  if ( PIN_getInputValue(Board_BTN2) == 0 )
+  {
+    keysPressed |= KEY_RIGHT;
+  }
+
+#elif defined (CC2650DK_7ID)  || defined (CC1350DK_7XD)
+  if ( PIN_getInputValue(Board_KEY_SELECT) == 0 )
+  {
+    keysPressed |= KEY_SELECT;
+  }
+
+  if ( PIN_getInputValue(Board_KEY_UP) == 0 )
+  {
+    keysPressed |= KEY_UP;
+  }
+
+  if ( PIN_getInputValue(Board_KEY_DOWN) == 0 )
+  {
+    keysPressed |= KEY_DOWN;
+  }
+
+  if ( PIN_getInputValue(Board_KEY_LEFT) == 0 )
+  {
+    keysPressed |= KEY_LEFT;
+  }
+
+  if ( PIN_getInputValue(Board_KEY_RIGHT) == 0 )
+  {
+    keysPressed |= KEY_RIGHT;
+  }
 #endif
 
-    Util_startClock(&keyChangeClock);
+  Util_startClock(&keyChangeClock);
 }
 
 /*********************************************************************

simplelink/ble_sdk_2_02_02_25/src/common/cc26xx/board_key.h

@@ -55,10 +55,11 @@ extern "C" {
 /*********************************************************************
  * INCLUDES
  */
+
 /*********************************************************************
 *  EXTERNAL VARIABLES
 */
-extern uint8_t KEY_INSTEAD_UART;
+
 /*********************************************************************
  * CONSTANTS
  */
@@ -67,11 +68,9 @@ extern uint8_t KEY_INSTEAD_UART;
 #define KEY_DOWN              0x0004
 #define KEY_LEFT              0x0008
 #define KEY_RIGHT             0x0010
-#define KEY_UART_EN           0x0020
-#define KEY_REQ               0x0040
 
 // Debounce timeout in milliseconds
-#define KEY_DEBOUNCE_TIMEOUT  0
+#define KEY_DEBOUNCE_TIMEOUT  200
 
 /*********************************************************************
  * TYPEDEFS

simplelink/ble_sdk_2_02_02_25/src/examples/simple_central/cc26xx/app/central_gptimer.h

@@ -1,44 +0,0 @@
-/* Copyright (c) 2021. WiseTop. Scientific.
- */
-#ifndef CENTRAL_GPTIMER_H
-#define CENTRAL_GPTIMER_H
-
-//#include <Board.h>
-#include <ti/drivers/timer/GPTimerCC26XX.h>
-#include <ti/sysbios/BIOS.h>
-#include <xdc/runtime/Types.h>
-
-static GPTimerCC26XX_Handle gptimer_handle;
-
-static void elite_gptimer_callback(GPTimerCC26XX_Handle handle, GPTimerCC26XX_IntMask interruptMask);
-
-#define elite_gptimer_start() GPTimerCC26XX_start(gptimer_handle)
-#define CLOCK_FREQ 4800  // clock freq = 0.1 ms(4800), Measured(4769)
-
-#define elite_gptimer_open()                                                                          \
-    do {                                                                                              \
-        GPTimerCC26XX_Params params;                                                                  \
-        GPTimerCC26XX_Params_init(&params);                                                           \
-        params.width          = GPT_CONFIG_16BIT;                                                     \
-        params.mode           = GPT_MODE_PERIODIC_UP;                                               \
-        params.debugStallMode = GPTimerCC26XX_DEBUG_STALL_OFF;                                        \
-        gptimer_handle        = GPTimerCC26XX_open(Board_GPTIMER0A, &params);                         \
-        Types_FreqHz  freq;                                                                           \
-        BIOS_getCpuFreq(&freq);                                                                       \
-        GPTimerCC26XX_Value loadVal = freq.lo / 1000 - 1; /*47999*/                                   \
-        GPTimerCC26XX_setLoadValue(gptimer_handle, loadVal);                                          \
-        GPTimerCC26XX_setLoadValue(gptimer_handle, CLOCK_FREQ); /* 0.1 ms*/                           \
-        GPTimerCC26XX_registerInterrupt(gptimer_handle, elite_gptimer_callback, GPT_INT_TIMEOUT);     \
-    } while (0)
-
-// GPT counter
-struct gp_timer_t
-{
-    uint32_t gp_timer_now;
-    uint32_t gp_timer_last;
-    uint8_t  gp_timer_delta;
-    uint32_t gp_timer_switch_ram;
-};
-
-
-#endif  // CENTRAL_GPTIMER_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_central/cc26xx/app/main.c

@@ -56,7 +56,6 @@
 
 #include "icall.h"
 #include "hal_assert.h"
-#include "board.h"
 #include "central.h"
 #include "simple_central.h"
 

simplelink/ble_sdk_2_02_02_25/src/examples/simple_central/cc26xx/app/mem_board_central.h

@@ -1,276 +0,0 @@
-
-/*
-* Reference web page https://github.com/ti-simplelink/ble_examples/tree/ble_examples-2.2
-*    http://software-dl.ti.com/dsps/dsps_public_sw/sdo_sb/targetcontent/tirtos/2_20_00_06/
-*           exports/tirtos_full_2_20_00_06/products/tidrivers_cc13xx_cc26xx_2_20_00_08/docs/
-*           doxygen/html/_u_a_r_t_c_c26_x_x_8h.html
-*/
-
-#ifndef MEM_BOARD_CENTRAL
-#define MEM_BOARD_CENTRAL
-
-#include <ti/sysbios/knl/Clock.h>
-#include "mem_central_pin.h"
-#include "mem_uart.h"
-#include "mem_central_handle_notify.h"
-#include "mem_uart_routine.h"
-
-
-#define BLE_CHAR2_HANDLE          0x0021    // read CIS return data
-#define BLE_CHAR3_HANDLE          0x0024    // send instruction
-#define BLE_CHAR4_CONFIG_HANDLE   0x0028    // notify enable: 0100=enable; 0000=disable
-
-#define RET_INFO_BUF_SIZE         52
-
-#define CIS_BUFF_PREFIX 3
-#define CIS_DATA_LEN 50
-static uint16_t CIS_length = 10;
-static char CIS_data[CIS_DATA_LEN];
-
-static void mem_central_event();
-static void mem_connect_device(uint8_t addrType, uint8_t *peerAddr);
-static void mem_send_ins(uint16_t hadnle, uint8_t *value);
-static void mem_read_data_and_return();
-static void mem_central_get_cis(uint8_t handle);
-
-static void MemBoard_init(void){
-    mem_UART_init();
-    master_spi_open();
-    central_ram_init();
-    central_reset();
-    flag_enable(EVT_MEM_UART_ROUTINE);
-}
-
-static EventTableEntry EVENT_TABLE[] = {  //
-    {EVT_ALL, &mem_central_event},
-
-    // terminated
-    {0, NULL}
-};
-
-/**
- * system event handle. It go through [EVENT_TABLE] and invoke event callback
- * if event_mask bits set.
- */
-static void mem_event_handle() {
-    for (EventTableEntry *entry = EVENT_TABLE; EventMask && entry->event_mask; entry++) {
-        if (entry->event_callback && flag_mask(entry->event_mask)) {
-            entry->event_callback();
-        }
-    }
-}
-
-static void mem_central_event() {
-    if(flag_mask(EVT_MEM_NOTIFY_HANDLE)){
-        flag_disable(EVT_MEM_NOTIFY_HANDLE);
-        central_handle_notify();
-    }
-
-    if(flag_mask(EVT_MEM_UART_ROUTINE)){
-        flag_disable(EVT_MEM_UART_ROUTINE);
-        mem_uart_routine();
-    }
-
-    if(flag_mask(EVT_MEM_INS_CHECK_SURVIVE)){
-        flag_disable(EVT_MEM_INS_CHECK_SURVIVE);
-
-        char ACK[15] = {4,0,1,3}; //ack success
-        UART_write(uart_handle, ACK, 4);
-    }
-
-    if(flag_mask(EVT_MEM_INS_SCAN)){
-        flag_disable(EVT_MEM_INS_SCAN);
-        SimpleBLECentral_discoverDevices();
-    }
-
-    if(flag_mask(EVT_MEM_INS_CONNECT)){
-        flag_disable(EVT_MEM_INS_CONNECT);
-        mem_connect_device(store_rxBuf[2], store_rxBuf+3);
-    }
-
-    if(flag_mask(EVT_MEM_INS_WRITE)){
-        flag_disable(EVT_MEM_INS_WRITE);
-        if(state == BLE_STATE_CONNECTED){
-        // This is done by SimpleBLECentral_processRoleEvent() in the case "GAP_LINK_ESTABLISHED_EVENT"
-            mem_send_ins(store_rxBuf[2], store_rxBuf+3);
-        }
-    }
-
-    if(flag_mask(EVT_MEM_INS_READ)){
-        flag_disable(EVT_MEM_INS_READ);
-        if(state == BLE_STATE_CONNECTED){
-            mem_central_get_cis(store_rxBuf[2]);
-        }
-    }
-
-    if(flag_mask(EVT_MEM_INS_DISCONNECT)){
-        flag_disable(EVT_MEM_INS_DISCONNECT);
-        GAPCentralRole_TerminateLink(connHandle);
-        state = BLE_STATE_DISCONNECTING;
-    }
-
-    if(flag_mask(EVT_MEM_RETURN_DATA)){
-        flag_disable(EVT_MEM_RETURN_DATA);
-        mem_read_data_and_return();
-    }
-}
-
-static void mem_connect_device(uint8_t addrType, uint8_t *peerAddr) {
-
-    uint8_t Addr[B_ADDR_LEN];
-
-    for(int i=0 ; i<B_ADDR_LEN ; i++){
-        Addr[5-i] = *(peerAddr+i);
-    }
-
-//    UART_write(uart_handle, Addr, 6);
-
-    state = BLE_STATE_CONNECTING;
-
-    Util_startClock(&connectingClock);
-
-    GAPCentralRole_EstablishLink(DEFAULT_LINK_HIGH_DUTY_CYCLE,
-                                 DEFAULT_LINK_WHITE_LIST,
-                                 addrType, Addr);
-}
-
-static void mem_send_ins(uint16_t handle, uint8_t *value){
-
-    if (state == BLE_STATE_CONNECTED &&
-        charHdl != 0                 &&
-        procedureInProgress == FALSE)
-    {
-        uint8_t ACK[15] = {0}; //ack success
-        ACK[1] = handle;
-        ACK[2] = value[0];
-        ACK[3] = value[1];
-        UART_write(uart_handle, ACK, 4);
-        uint8_t status;
-
-        // Do a read or write as long as no other read or write is in progress
-        // Do a write
-        attWriteReq_t req;
-
-        // enable notify
-        req.handle = handle;
-        req.len = 19;
-        if(handle == BLE_CHAR3_HANDLE){
-            // RIS, VIS, CIS instruction
-            req.len = 19;
-        }
-        else if(handle == BLE_CHAR4_CONFIG_HANDLE){
-            // notify enable
-            req.len = 2;
-        }
-        else{
-            uint8_t error_handle[13] = "error handle";
-            UART_write(uart_handle, error_handle, 13);
-            status = bleMemAllocError;
-            return;
-        }
-
-        req.pValue = GATT_bm_alloc(connHandle, ATT_WRITE_REQ, req.len, NULL);
-        if ( req.pValue != NULL )
-        {
-            // send instruction
-            for(int i=0 ; i < req.len ; i++){
-                req.pValue[i] = *(value+i);
-            }
-            req.sig = 0;
-            req.cmd = 0;
-            status = GATT_WriteCharValue(connHandle, &req, selfEntity);
-
-            // uncomment GATT_WriteLongCharValue if we need a long instruction;
-            // However, there are some error to fix when using GATT_WriteLongCharValue
-//            status = GATT_WriteLongCharValue(connHandle, &req, selfEntity);
-
-            if ( status != SUCCESS )
-            {
-                GATT_bm_free((gattMsg_t *)&req, ATT_WRITE_REQ);
-            }
-        }
-        else
-        {
-            uint8_t error_msg[10] = "err";
-            error_msg[3] = req.handle;
-            error_msg[4] = *value;
-            error_msg[5] = *(value+1);
-            error_msg[6] = *(value+2);
-            error_msg[7] = *(value+3);
-            error_msg[8] = *(value+4);
-            error_msg[9] = *(value+5);
-            UART_write(uart_handle, error_msg, 10);
-            status = bleMemAllocError;
-        }
-
-        if (status == SUCCESS)
-        {
-            procedureInProgress = TRUE;
-        }
-    }
-}
-
-static void mem_central_get_cis(uint8_t handle){
-    // get the actual CIS data from simple_central.c > SimpleBLECentral_processGATTMsg()
-    if (state == BLE_STATE_CONNECTED &&
-        charHdl != 0                 &&
-        procedureInProgress == FALSE)
-    {
-        uint8_t status;
-
-        // send read command
-        attReadReq_t read_cis_req;
-        read_cis_req.handle = handle;
-        status = GATT_ReadCharValue(connHandle, &read_cis_req, selfEntity);
-
-        if (status == SUCCESS)
-        {
-            procedureInProgress = TRUE;
-        }
-    }
-}
-
-static void mem_read_data_and_return(){
-    /*
-     *  CIS data formate:
-     *  Elite send to central:
-     *      +------------+------------------+
-     *      | Header(1B) |    Payload(nB)   |
-     *      +------------+------------------+
-     *      |d0(recv_len)|  d1, d2, d3, ... |
-     *      +------------+------------------+
-     *  ex: |    0x03    |  0x10,0xC0,0x01  |               <--- barrery data
-     *      +------------+------------------+
-     *
-     *  central send to controller:
-     *      +--------------------+------------------+
-     *      |     Header(3B)     |      Payload     |
-     *      +---+---+------------+------------------+
-     *      | 4 | 0 | ret_length |  d1, d2, d3, ... |
-     *      +---+---+------------+------------------+
-     *  ex: | 4 | 0 |    0x14    |  0x10,0xC0,0x01  |       <--- barrery data
-     *      +---+---+------------+------------------+
-     *
-     */
-
-    // add prefix and suffix to sync communication
-    uint16_t ret_length;
-
-    if (CIS_length < 22) {
-        ret_length = 20;
-    } else {
-        ret_length = CIS_length - CIS_BUFF_PREFIX;
-    }
-
-    CIS_data[0] = 4;
-    CIS_data[1] = 0;
-    CIS_data[2] = ret_length;
-    CIS_data[CIS_length++] = 0;
-    CIS_data[CIS_length++] = 0;
-
-    UART_write(uart_handle, CIS_data, ret_length + CIS_BUFF_PREFIX);
-
-    memset(CIS_data, 0, CIS_DATA_LEN);
-}
-
-#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_central/cc26xx/app/mem_central_handle_notify.h

@@ -1,313 +0,0 @@
-
-#ifndef CENTRAL_NOTIFY
-#define CENTRAL_NOTIFY
-
-#include "mem_event.h"
-#include "mem_uart.h"
-#include "mem_central_pin.h"
-#include "mem_central_spi.h"
-#include "mem_board_central.h"
-
-/*========================
- ==== notify variable ====
- =======================*/
-
-#define MEM_BUFFER_SIZE         SPI_TX_BUFFER_SIZE // 250
-
-#define MSM_REG_WRITE 0x01
-#define MEM_INS_WRITE 0x02
-#define MEM_INS_READ  0x03
-
-#define MEM_META_LENGTH 12
-
-#define central_ram_init()                      \
-    do {                                        \
-        master_tx_buffer[0] = MSM_REG_WRITE;    \
-        master_tx_buffer[1] = 0b01000011;       \
-        central_ram_select(1);                  \
-        central_spi_send(master_tx_buffer, 2);  \
-        central_ram_select(0);                  \
-        central_spi_send(master_tx_buffer, 2);  \
-    } while (0)
-
-
-static uint16_t not_counter = 0;  // writing counter, increase when notify
-static uint16_t not_offset  = 0;  // writing pointer, where to write on RAM
-
-static uint16_t notify_length = 0;
-static uint8_t notify_value[MEM_BUFFER_SIZE] = {0}; // recv data from elite
-
-void master_switch_memory();
-
-static void central_reset()
-{
-    not_counter = 0;
-    not_offset  = MEM_META_LENGTH;
-    ram_sel_signal = false;
-    central_ram_select(ram_sel_signal);
-
-}
-
-static void reset_status_register()
-{
-    uint8_t status_register_buf[2];
-    status_register_buf[0] = MSM_REG_WRITE;
-    status_register_buf[1] = 0b01000011;
-    central_spi_send(status_register_buf, 2);
-
-}
-
-#define RAM_INS_LEN             3
-
-#define RAM_RED_HEADER_LEN      3
-#define RAM_RED_TAILER_LEN      5
-#define ELITE_NOTIFY_LEN        40
-#define RAM_RED_CHECK_SUM_LEN   1
-#define RAM_RED_DATA_LEN    (RAM_RED_HEADER_LEN + RAM_RED_TAILER_LEN + ELITE_NOTIFY_LEN + RAM_RED_CHECK_SUM_LEN)
-#define RAM_RED_CTX_LEN     (RAM_INS_LEN + RAM_RED_DATA_LEN)
-
-#define RAM_GREEN_CTX_LEN   (MEM_META_LENGTH + RAM_INS_LEN)
-
-static uint8_t green_wrong = 0;
-static uint8_t green_retry_cnt = 0;
-
-uint8_t check_sum(uint8_t message[], int nBytes)
-{
-    uint8_t sum = 0;
-
-    while (nBytes-- > 0) {
-        sum += *(message++);
-    }
-
-    return sum;
-
-}
-
-static void central_handle_notify()
-{
-    uint8_t spi_buffer0[MEM_BUFFER_SIZE] = {0};
-    uint8_t spi_buffer1[MEM_BUFFER_SIZE] = {0};
-    uint8_t read_ram_ins[RAM_RED_CTX_LEN] = {0};
-    uint8_t read_ram_buf[RAM_RED_CTX_LEN] = {0};
-    uint8_t tailer[RAM_RED_TAILER_LEN] = {0};
-    static bool spi_buffer_index = true;
-    static uint8_t wrong = 0;
-    static uint8_t retry_cnt = 0;
-    bool wrong_flag = false;
-    bool write_again = false;
-    uint8_t write_limit = 0;
-    uint8_t check_number = 0;
-    uint8_t pkg_cnt;
-    uint8_t *p;
-    int index;
-    int i;
-
-    // localize current buffer
-    if (spi_buffer_index) {
-        spi_buffer_index = false;
-        p = spi_buffer0;
-    } else {
-        spi_buffer_index = true;
-        p = spi_buffer1;
-    }
-
-    memset(p, 0, MEM_BUFFER_SIZE);
-    pkg_cnt = not_counter;
-    not_counter = not_counter + 1;
-
-    // update offset
-    uint32_t cnt_offset = not_offset;
-    if (not_offset > 7500) {
-        not_offset = not_offset;
-    } else {
-        not_offset = not_offset + RAM_RED_DATA_LEN;
-    }
-
-    tailer[0] = wrong;
-    tailer[1] = retry_cnt;
-    tailer[2] = green_wrong;
-    tailer[3] = green_retry_cnt;
-    tailer[4] = ram_sel_signal;
-
-    p[0] = MEM_INS_WRITE;                                  // instruction
-    p[1] = (uint8_t)((cnt_offset >> 8) & 0xFF);            // address
-    p[2] = (uint8_t)(cnt_offset & 0xFF);                   // address
-    p[3] = 0xFF;                                           // RAM_RED_HEADER_LEN: data header
-    p[4] = pkg_cnt;                                        // RAM_RED_HEADER_LEN: data counter
-    p[5] = notify_length;                                  // RAM_RED_HEADER_LEN: data content length
-
-    index = RAM_INS_LEN + RAM_RED_HEADER_LEN;
-    memcpy(p + index, notify_value, ELITE_NOTIFY_LEN);     // ELITE_NOTIFY_LEN: data content
-
-    index += ELITE_NOTIFY_LEN;
-    memcpy(p + index, tailer, RAM_RED_TAILER_LEN);         // RAM_RED_TAILER_LEN: tailer content
-
-    index += RAM_RED_TAILER_LEN;
-    p[index] = check_sum(p+3, RAM_RED_DATA_LEN - RAM_RED_CHECK_SUM_LEN); // RAM_RED_CHECK_SUM_LEN
-
-    central_spi_send(p, RAM_RED_CTX_LEN);
-
-    // read RAM
-    read_ram_ins[0] = 0x03; //read RAM
-    read_ram_ins[1] = (uint8_t)((cnt_offset >> 8) & 0xFF); // address
-    read_ram_ins[2] = (uint8_t)(cnt_offset & 0xFF); // address
-    central_spi_recv(read_ram_ins, read_ram_buf);
-
-    while (1) {
-        // compare data
-        check_number = check_sum(p+3, RAM_RED_DATA_LEN - RAM_RED_CHECK_SUM_LEN);
-        if (check_number != p[RAM_RED_CTX_LEN-1]) {
-            write_again = true;
-            memset(p+3, 255, RAM_RED_DATA_LEN - RAM_RED_CHECK_SUM_LEN);
-            p[RAM_RED_CTX_LEN-1] = check_sum(p+3, RAM_RED_DATA_LEN - RAM_RED_CHECK_SUM_LEN);
-
-        } else {
-            check_number = check_sum(read_ram_buf+3, RAM_RED_DATA_LEN - RAM_RED_CHECK_SUM_LEN);
-            if (check_number != read_ram_buf[RAM_RED_CTX_LEN-1]) {
-                write_again = true;
-            }
-
-        }
-
-        if (write_again == false) {
-            for (i=3; i<RAM_RED_CTX_LEN; i++) {
-                if (p[i]!=read_ram_buf[i]) {
-                    write_again = true;
-                    break;
-                }
-            }
-        }
-
-        if (write_again) {
-            reset_status_register();
-            CPUdelay(10 * 16); // 10us
-
-            write_again = false;
-            retry_cnt++;
-            write_limit++;
-
-            //write RAM
-            central_spi_send(p, RAM_RED_CTX_LEN);
-
-            // read RAM
-            read_ram_ins[0] = 0x03; //read RAM
-            read_ram_ins[1] = (uint8_t)((cnt_offset >> 8) & 0xFF); // address
-            read_ram_ins[2] = (uint8_t)(cnt_offset & 0xFF); // address
-            central_spi_recv(read_ram_ins, read_ram_buf);
-
-        } else {
-            break;
-        }
-
-        if (write_limit >= 5) {
-            break;
-        }
-    }
-
-    for (i=3; i<RAM_RED_CTX_LEN; i++) {
-        if (p[i] != read_ram_buf[i]) {
-            wrong_flag = true;
-            break;
-        }
-    }
-
-    if (wrong_flag) {
-        wrong++;
-        reset_status_register();
-        CPUdelay(10 * 16); // 10us
-    }
-
-    // if (ram_sel_signal) {
-    //     central_pin_output(PIN_MEM_TEST, 1);
-    // } else {
-    //     central_pin_output(PIN_MEM_TEST, 0);
-    // }
-
-}
-
-void master_switch_memory()
-{
-    uint8_t read_ram_ins[RAM_GREEN_CTX_LEN] = {0};
-    uint8_t read_ram_buf[RAM_GREEN_CTX_LEN] = {0};
-    uint8_t *p = master_tx_buffer; // localize current buffer
-    bool wrong_flag = false;
-    bool write_again = false;
-    uint8_t write_limit = 0;
-    uint16_t cnt_offset;
-    int i;
-
-    cnt_offset = not_offset;
-    not_offset = MEM_META_LENGTH;
-
-    memset(p, 0, sizeof(master_tx_buffer)/sizeof(master_tx_buffer[0]));
-    p[0] = MEM_INS_WRITE;                               // instruction
-    p[1] = 0;
-    p[2] = 0;
-    p[3] = (uint8_t)((cnt_offset >> 8) & 0xFF);  // data: notify data length
-    p[4] = (uint8_t)(cnt_offset & 0xFF);         // data: notify data length
-    p[5] = 0xA5;
-    p[6] = 0x5A;
-    memcpy(p + 7, p + 3, 4);
-    memcpy(p + 11, p + 3, 4);
-    central_spi_send(p, RAM_GREEN_CTX_LEN);
-
-    // read RAM
-    read_ram_ins[0] = MEM_INS_READ; //read RAM
-    read_ram_ins[1] = 0; // address
-    read_ram_ins[2] = 0; // address
-    central_spi_recv(read_ram_ins, read_ram_buf);
-
-    while (1) {
-        // compare data
-        for (i=3; i<RAM_GREEN_CTX_LEN; i++) {
-            if (p[i] != read_ram_buf[i]) {
-                write_again = true;
-                break;
-            }
-        }
-
-        if (write_again) {
-            write_again = false;
-            green_retry_cnt++;
-            write_limit++;
-            reset_status_register();
-            CPUdelay(10 * 16); // 10us
-
-            //write RAM
-            central_spi_send(p, RAM_GREEN_CTX_LEN);
-
-            // read RAM
-            read_ram_ins[0] = MEM_INS_READ; //read RAM
-            read_ram_ins[1] = 0; // address
-            read_ram_ins[2] = 0; // address
-            central_spi_recv(read_ram_ins, read_ram_buf);
-
-        } else {
-            break;
-        }
-
-        if (write_limit >= 5) {
-            break;
-        }
-    }
-
-    for (i=3; i<RAM_GREEN_CTX_LEN; i++) {
-        if (p[i] != read_ram_buf[i]) {
-            wrong_flag = true;
-            break;
-        }
-    }
-
-    if (wrong_flag) {
-        green_wrong++;
-    }
-
-    // switch memory
-    ram_sel_signal = !ram_sel_signal;
-    central_ram_select(ram_sel_signal);
-
-    CPUdelay(10 * 16); // 10us
-
-}
-
-#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_central/cc26xx/app/mem_central_pin.h

@@ -1,13 +0,0 @@
-
-#ifndef MEM_CENTRAL_PIN
-#define MEM_CENTRAL_PIN
-
-//extern PIN_State  keyPins;
-extern PIN_Handle hKeyPins;
-
-#define central_pin_output(pin, value) PIN_setOutputValue(hKeyPins, PIN_ID(pin), (value))
-#define central_pin_input(pin) PIN_getInputValue(PIN_ID(pin))
-
-#define central_ram_select(value) central_pin_output(PIN_RAM_SEL, (value) ? 1 : 0)
-
-#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_central/cc26xx/app/mem_central_spi.h

@@ -1,52 +0,0 @@
-#ifndef CENTRAL_SPI_H
-#define CENTRAL_SPI_H
-
-// clang-format off
-#include <ti/drivers/SPI.h>
-#include <ti/drivers/dma/UDMACC26XX.h>
-#include <ti/drivers/spi/SPICC26XXDMA.h>
-// clang-format on
-
-#include "mem_central_pin.h"
-
-#define SPI_TX_BUFFER_SIZE 250
-
-static uint8_t master_tx_buffer[SPI_TX_BUFFER_SIZE] = {0};
-
-static SPI_Handle      central_spi_handle;
-static SPI_Transaction central_spi_transaction;
-
-#define master_spi_open()                                                      \
-    do {                                                                       \
-        SPI_init();                                                            \
-        SPI_Params spi_parameter;                                              \
-        SPI_Params_init(&spi_parameter);                                       \
-        spi_parameter.transferMode    = SPI_MODE_BLOCKING;                     \
-        spi_parameter.mode            = SPI_MASTER;                            \
-        spi_parameter.bitRate         = 12000000;                              \
-        spi_parameter.transferTimeout = 1000;                                  \
-        spi_parameter.dataSize        = 8;                                     \
-        spi_parameter.frameFormat     = SPI_POL0_PHA0;                         \
-        central_spi_handle             = SPI_open(Board_SPI0, &spi_parameter); \
-    } while (0)
-
-#define central_spi_send(data, len)                                  \
-    do {                                                             \
-        central_spi_transaction.txBuf = data;                        \
-        central_spi_transaction.rxBuf = NULL;                        \
-        central_spi_transaction.count = (len);                       \
-        central_pin_output(Board_SPI_CS, 0);                         \
-        SPI_transfer(central_spi_handle, &central_spi_transaction);  \
-        central_pin_output(Board_SPI_CS, 1);                         \
-    } while (0)
-
-#define central_spi_recv(ins, data)                                  \
-    do {                                                             \
-        central_spi_transaction.txBuf = ins;                         \
-        central_spi_transaction.rxBuf = data;                        \
-        central_pin_output(Board_SPI_CS, 0);                         \
-        SPI_transfer(central_spi_handle, &central_spi_transaction);  \
-        central_pin_output(Board_SPI_CS, 1);                         \
-    } while (0)
-
-#endif  // CENTRAL_SPI_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_central/cc26xx/app/mem_event.h

@@ -1,66 +0,0 @@
-
-#ifndef MEM_EVENT_H
-#define MEM_EVENT_H
-
-/**
- * test event [flag] has been enabled.
- */
-#define flag_mask(flag) ((EventMask & (flag)) != 0)
-
-/**
- * enable event [flag].
- */
-#define flag_enable(flag)               \
-    do {                                \
-        uint8 __key = Hwi_disable();    \
-        EventMask |= (uint16_t)(flag);  \
-        Hwi_restore(__key);             \
-    } while (0)
-
-/**
- * disable event [flag].
- */
-#define flag_disable(flag)                 \
-    do {                                   \
-        uint8 __key = Hwi_disable();       \
-        EventMask &= ~((uint16_t)(flag));  \
-        Hwi_restore(__key);                \
-    } while (0)
-
-/**
- * fire a event with [flag].
- */
-#define flag_notify(flag)               \
-    do {                                \
-        uint8 __key = Hwi_disable();    \
-        EventMask |= (uint16_t)(flag);  \
-        Hwi_restore(__key);             \
-        Semaphore_post(sem);            \
-    } while (0)
-
-/** event */
-#define EVT_ALL                  0xFFFF
-#define EVT_MEM_RETURN_DATA      0x0010
-#define EVT_MEM_NOTIFY_HANDLE    0x0040
-#define EVT_MEM_UART_ROUTINE     0x0080
-
-uint16_t EventMask = 0;
-
-/**
- * event table entry.
- */
-typedef struct {
-    /**
-     * event mask.
-     */
-    uint16_t event_mask;
-
-    /**
-     * event callback. invoked  by system when system [EVENT_MASK] set with
-     * [event_mask] bits.
-     */
-    void (*event_callback)();
-} EventTableEntry;
-
-
-#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_central/cc26xx/app/mem_uart.h

@@ -1,148 +0,0 @@
-
-#ifndef MEM_UART
-#define MEM_UART
-
-/*
-*  http://software-dl.ti.com/dsps/dsps_public_sw/sdo_sb/targetcontent/tirtos/
-*  2_20_00_06/exports/tirtos_full_2_20_00_06/products/tidrivers_cc13xx_cc26xx_2_20_00_08/
-*  docs/doxygen/html/_u_a_r_t_c_c26_x_x_8h.html
-*/
-
-#include <ti/drivers/UART.h>
-#include <ti/drivers/uart/UARTCC26XX.h>
-#include "mem_event.h"
-
-#define UART_BUFF_SIZE 241
-
-static UART_Handle uart_handle;
-static UART_Params params;
-
-static uint8_t UART_rxBuf[UART_BUFF_SIZE];
-
-static uint8_t store_rxBuf[UART_BUFF_SIZE];
-
-typedef enum{
-    INS_IDLE,
-    INS_RESET,
-    INS_KEY,
-    INS_SCAN,
-    INS_SCAN_RESPONSE,
-    INS_CONNECT,
-    INS_WRITE,
-    INS_READ,
-    INS_DISCONNECT,
-    INS_PREPARE_CONNECT,
-    INS_CHECK_SURVIVE
-} Control_Ins;
-
-/** event */
-#define EVT_ALL                     0xFFFF
-#define EVT_MEM_RETURN_DATA         0x0010
-#define EVT_MEM_NOTIFY_HANDLE       0x0040
-#define EVT_MEM_UART_ROUTINE        0x0080
-#define EVT_MEM_INS_SCAN            0x0100
-#define EVT_MEM_INS_CONNECT         0x0200
-#define EVT_MEM_INS_WRITE           0x0400
-#define EVT_MEM_INS_READ            0x0800
-#define EVT_MEM_INS_DISCONNECT      0x1000
-#define EVT_MEM_INS_CHECK_SURVIVE   0x2000
-
-
-#define IS_EVT_MEM_DECODE_INS(_b)       ((_b)[0] == INS_SCAN    || \
-                                         (_b)[0] == INS_CONNECT || \
-                                         (_b)[0] == INS_WRITE   || \
-                                         (_b)[0] == INS_READ    || \
-                                         (_b)[0] == INS_DISCONNECT || \
-                                         (_b)[0] == INS_CHECK_SURVIVE)
-
-
-// Callback function
-static void readCallback(UART_Handle handle, void *rxBuf, size_t size)
-{
-    uint8_t *uart_rxBuf = (uint8_t *)rxBuf;
-    static int index = 0;
-    static int length = 0;
-    static bool rx_fi = false;
-
-    if (rx_fi) {
-        memset(store_rxBuf, 0, UART_BUFF_SIZE);
-        rx_fi = false;
-    }
-
-    if (IS_EVT_MEM_DECODE_INS(uart_rxBuf) && index == 0) {
-        store_rxBuf[0] = uart_rxBuf[0];
-        index++;
-    } else if (IS_EVT_MEM_DECODE_INS(store_rxBuf) && index == 1) {
-        store_rxBuf[1] = uart_rxBuf[0];
-        length = uart_rxBuf[0];
-        index++;
-    } else if (IS_EVT_MEM_DECODE_INS(store_rxBuf) && index > 1) {
-        store_rxBuf[index] = uart_rxBuf[0];
-        if (index >= length + 2) { //num = 0 when over length
-            store_rxBuf[index] = 0;
-        }
-        index++;
-    }
-
-    //0xF1 = 241
-    if(index > 1 && store_rxBuf[0] == INS_SCAN && store_rxBuf[length + 1] == 0xF1 ) {
-        index = 0;
-        length = 0;
-        flag_notify(EVT_MEM_INS_SCAN);
-        flag_notify(EVT_MEM_UART_ROUTINE);
-        rx_fi = true;
-        return;
-    } else if (index > 1 && store_rxBuf[0] == INS_CONNECT && store_rxBuf[length + 1] == 0xF1) {
-        index = 0;
-        length = 0;
-        flag_notify(EVT_MEM_INS_CONNECT);
-        flag_notify(EVT_MEM_UART_ROUTINE);
-        rx_fi = true;
-        return;
-    } else if (index > 1 && store_rxBuf[0] == INS_WRITE && store_rxBuf[length + 1] == 0xF1) {
-        index = 0;
-        length = 0;
-        flag_notify(EVT_MEM_INS_WRITE);
-        flag_notify(EVT_MEM_UART_ROUTINE);
-        rx_fi = true;
-        return;
-    } else if (index > 1 && store_rxBuf[0] == INS_READ && store_rxBuf[length + 1] == 0xF1) {
-        index = 0;
-        length = 0;
-        flag_notify(EVT_MEM_INS_READ);
-        flag_notify(EVT_MEM_UART_ROUTINE);
-        rx_fi = true;
-        return;
-    } else if (index > 1 && store_rxBuf[0] == INS_DISCONNECT && store_rxBuf[length + 1] == 0xF1) {
-        flag_notify(EVT_MEM_INS_DISCONNECT);
-        index = 0;
-        length = 0;
-        flag_notify(EVT_MEM_UART_ROUTINE);
-        rx_fi = true;
-        return;
-    } else if (index > 1 && store_rxBuf[0] == INS_CHECK_SURVIVE && store_rxBuf[length + 1] == 0xF1) {
-        flag_notify(EVT_MEM_INS_CHECK_SURVIVE);
-        index = 0;
-        length = 0;
-        flag_notify(EVT_MEM_UART_ROUTINE);
-        rx_fi = true;
-        return;
-    }
-    flag_notify(EVT_MEM_UART_ROUTINE);
-}
-
-static void mem_UART_init(){
-    // Init UART and specify non-default parameters
-    UART_Params_init(&params);
-    params.baudRate      = 115200;
-    params.writeDataMode = UART_DATA_BINARY;
-    params.readMode      = UART_MODE_CALLBACK;
-    params.readDataMode  = UART_DATA_BINARY;
-    params.readCallback  = readCallback;;
-
-    // Open the UART and do the read
-    uart_handle = UART_open(Board_UART, &params);
-    return;
-}
-
-#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_central/cc26xx/app/mem_uart_routine.h

@@ -1,17 +0,0 @@
-
-#ifndef MEM_UART_ROUTINE_H
-#define MEM_UART_ROUTINE_H
-
-#include "mem_uart.h"
-#include "mem_event.h"
-
-static void mem_uart_routine(){
-    if (uartProcedureInProgress == FALSE) {
-//        uartProcedureInProgress = TRUE;
-        int rxBytes = UART_read(uart_handle, UART_rxBuf, 1);
-    } else {
-        flag_notify(EVT_MEM_UART_ROUTINE);
-    }
-}
-
-#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/boards_config/elite_boards_select.h

@@ -0,0 +1,143 @@
+#ifndef ELITE_BOARDS_SELECT_H
+#define ELITE_BOARDS_SELECT_H
+
+#ifdef  __cplusplus
+extern "C" {
+#endif
+
+/*
+ *
+ * product number: MAJOR_PRODUCT_NUMBER, MINOR_PRODUCT_NUMBER, MAJOR_VERSION_NUMBER, MINOR_VERSION_NUMBER
+ * MAJOR_PRODUCT_NUMBER -> 0:Elite, 1:other serial
+ * Elite:
+ *      MINOR_PRODUCT_NUMBER -> 1:legacy, 2:EDC, 3:BAT, 4:EIS, 5:TRIG, 6:MEGAFLY
+ *
+ * +------------------------+----------------------+-------------------------+----------------+----------------------+----------------------+----------+
+ * |       model name       |   hw upper board     |    hw lower board       | product number |      device name     | data server lib name |    UI    |
+ * +------------------------+----------------------+-------------------------+----------------+----------------------+----------------------+----------+
+ * | DEF_ELITE_EDC_14       | Elite1.4-re Jun.2019 | Elite1.4-re Jun. 2019   |   0, 2, 1, 5   | "Elite-EDC"          | Elite_EDC_1.4        | null     |
+ * | DEF_ELITE_EDC_15       | Elite1.5 Dec. 2019   | Elite1.5 Dec. 2019      |   0, 2, 1, 6   | "Elite-EDC"          | Elite_EDC_1.5        | EliteEDC |
+ * | DEF_ELITE_EDC_15RE     | Elite1.5 Dec. 2019   | Elite1.5-re Jan. 2021   |   0, 2, 1, 7   | "Elite-EDC"          | Elite_EDC_1.5re      | EliteEDC |
+ * | DEF_ELITE_EDC_15R2     | Elite1.5 Dec. 2019   | Elite1.5-r2 May. 2022   |   0, 2, 1, 8   | "Elite-EDC"          | Elite_EDC_1.5r2      | EliteEDC |
+ * | DEF_ELITE_BAT_10       |             Elite2.0 Feb. 2022                 |   0, 3, 1, 0   | "Elite-BAT"          | Elite_BAT_1.0        | EliteEDC |
+ * | DEF_ELITE_EIS_10       | Elite1.5 Dec. 2019   | Elite EIS1.0 Aug. 2020  |   0, 4, 1, 0   | "Elite-EIS"          | Elite_EIS_1.0        | EliteEIS |
+ * | DEF_ELITE_EIS_11       | Elite1.5 Dec. 2019   | Elite EIS1.1 Feb. 2022  |   0, 4, 1, 1   | "Elite-EIS"          | Elite_EIS_1.1        | EliteEIS |
+ * | DEF_ELITE_EIS_MINI_10  |             EIS MINI May. 2022                 |   0, 4, 1, 2   | "Elite-EIS-MINI"     | Elite_EIS_MINI_1.0   | EliteEIS |
+ * | DEF_ELITE_TRIG_01      |            Elite TRIG01 Jan. 2021              |   0, 5, 1, 0   | "Elite-TRIG"         | Elite_TRIG_0.1       | null     |
+ * | DEF_ELITE_MEGAFLY_01   | Elite1.5 Dec. 2019   | Elite Megafly Sep. 2020 |   0, 6, 1, 0   | "Elite-MEGAFLY"      | Elite_MEGAFLY_0.1    | null     |
+ * +------------------------+----------------------+-------------------------+----------------+----------------------+----------------------+----------+
+ * ps.
+ *    model name is FW engineer defined
+ *    device name is used for controller
+ */
+
+
+#define DEF_ELITE_EDC_14        0
+#define DEF_ELITE_EDC_15        1
+#define DEF_ELITE_EDC_15RE      2
+#define DEF_ELITE_EDC_15R2      3
+#define DEF_ELITE_BAT_10        4
+#define DEF_ELITE_EIS_10        5
+#define DEF_ELITE_EIS_11        6
+#define DEF_ELITE_EIS_MINI_10   7
+#define DEF_ELITE_TRIG_01       8
+#define DEF_ELITE_MEGAFLY_01    9
+#define DEF_ELITE_MAX           10
+
+#define DEF_ELITE_MODEL    DEF_ELITE_EIS_11
+#ifndef DEF_ELITE_MODEL
+#error "DEF_ELITE_MODEL not defined"
+#endif
+
+#if (DEF_ELITE_MODEL == DEF_ELITE_EDC_14)
+    #error "code no support"    // need fix
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EDC_15)
+    #error "code no support"    // need fix
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EDC_15RE)
+    #include "boards_config/pin_def_edc15re.h"
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EDC_15R2)
+    #error "code no support"    // need fix
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EIS_10)
+    #error "code no support"    // need fix
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EIS_11)
+    #include "boards_config/pin_def_eis11.h"
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EIS_MINI_10)
+    #include "boards_config/pin_config_eis_mini_10.h"
+#elif (DEF_ELITE_MODEL == DEF_ELITE_BAT_10)
+    #error "code no support"    // need fix
+#elif (DEF_ELITE_MODEL == DEF_ELITE_MEGAFLY_01)
+    #error "code no support"    // need fix
+#elif (DEF_ELITE_MODEL == DEF_ELITE_TRIG_01)
+    #error "code no support"    // need fix
+#else
+    #error "no this model"
+#endif
+
+
+// model information
+#if (DEF_ELITE_MODEL == DEF_ELITE_EDC_14)
+    #define DEVICE_NAME             "Elite-EDC"
+    #define MAJOR_PRODUCT_NUMBER    0
+    #define MINOR_PRODUCT_NUMBER    2
+    #define MAJOR_VERSION_NUMBER    1
+    #define MINOR_VERSION_NUMBER    5
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EDC_15)
+    #define DEVICE_NAME             "Elite-EDC"
+    #define MAJOR_PRODUCT_NUMBER    0
+    #define MINOR_PRODUCT_NUMBER    2
+    #define MAJOR_VERSION_NUMBER    1
+    #define MINOR_VERSION_NUMBER    6
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EDC_15RE)
+    #define DEVICE_NAME             "Elite-EDC"
+    #define MAJOR_PRODUCT_NUMBER    0
+    #define MINOR_PRODUCT_NUMBER    2
+    #define MAJOR_VERSION_NUMBER    1
+    #define MINOR_VERSION_NUMBER    7
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EDC_15R2)
+    #define DEVICE_NAME             "Elite-EDC"
+    #define MAJOR_PRODUCT_NUMBER    0
+    #define MINOR_PRODUCT_NUMBER    2
+    #define MAJOR_VERSION_NUMBER    1
+    #define MINOR_VERSION_NUMBER    8
+#elif (DEF_ELITE_MODEL == DEF_ELITE_BAT_10)
+    #define DEVICE_NAME             "Elite-BAT"
+    #define MAJOR_PRODUCT_NUMBER    0
+    #define MINOR_PRODUCT_NUMBER    3
+    #define MAJOR_VERSION_NUMBER    1
+    #define MINOR_VERSION_NUMBER    0
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EIS_10)
+    #define DEVICE_NAME             "Elite-EIS"
+    #define MAJOR_PRODUCT_NUMBER    0
+    #define MINOR_PRODUCT_NUMBER    4
+    #define MAJOR_VERSION_NUMBER    1
+    #define MINOR_VERSION_NUMBER    0
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EIS_11)
+    #define DEVICE_NAME             "Elite-EIS"
+    #define MAJOR_PRODUCT_NUMBER    0
+    #define MINOR_PRODUCT_NUMBER    4
+    #define MAJOR_VERSION_NUMBER    1
+    #define MINOR_VERSION_NUMBER    1
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EIS_MINI_10)
+    #define DEVICE_NAME             "Elite-EIS"
+    #define MAJOR_PRODUCT_NUMBER    0
+    #define MINOR_PRODUCT_NUMBER    4
+    #define MAJOR_VERSION_NUMBER    1
+    #define MINOR_VERSION_NUMBER    2
+#elif (DEF_ELITE_MODEL == DEF_ELITE_TRIG_01)
+    #define DEVICE_NAME             "Elite-TRIG"
+    #define MAJOR_PRODUCT_NUMBER    0
+    #define MINOR_PRODUCT_NUMBER    5
+    #define MAJOR_VERSION_NUMBER    1
+    #define MINOR_VERSION_NUMBER    0
+#elif (DEF_ELITE_MODEL == DEF_ELITE_MEGAFLY_01)
+    #define DEVICE_NAME             "Elite-MEGAFLY"
+    #define MAJOR_PRODUCT_NUMBER    0
+    #define MINOR_PRODUCT_NUMBER    6
+    #define MAJOR_VERSION_NUMBER    1
+    #define MINOR_VERSION_NUMBER    0
+#endif
+
+#ifdef  __cplusplus
+}
+#endif
+#endif  // ELITE_BOARDS_SELECT_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/boards_config/pin_config_eis_mini_10.h

@@ -0,0 +1,81 @@
+/*
+ * +------------------------------+
+ * |          CC2650moda          |
+ * +-------------+----------------+
+ * | MISO        | DIO1           |
+ * | D0          | DIO3           |
+ * | D1          | DIO4           |
+ * | D2/JTAG_TDO | DIO5/JTAG_TDO  |
+ * | D3/JTAG_TDI | DIO6/JTAG_TDI  |
+ * | D4          | DIO7           |
+ * | D5          | DIO8           |
+ * | D6          | DIO9           |
+ * | D7          | DIO10          |
+ * | LOAD2       | DIO11          |
+ * | LOAD1       | DIO12          |
+ * | LOAD0       | DIO13          |
+ * | SHUT_DOWN   | DIO14          |
+ * +-------------+----------------+
+ *
+ * +-----------------------------+
+ * | Elite Pin for EIS1.1 Board  |
+ * +------------+----------------+
+ * | AD_GPIO2   | D0             |
+ * | AD_GPIO1   | D1             |
+ * | AD_CLK     | D2             |
+ * | AD_MOSI    | D3             |
+ * | AD_RST     | D4             |
+ * | MEM_CS     | D5             |
+ * | 5V_ENABLE  | D6             |
+ * | AD_CS      | D7             |
+ * | AD_GPIO0   | LOAD2          |
+ * | OFF        | LOAD0          |<--OFF:shutdown_6994
+ * | AD_MISO    | MISO           |
+ * | SHUT_DOWN  | SHUT_DOWN      |<--SHUT_DOWN:switch on/off
+ * +------------+----------------+
+ * | LED_SCLK_A | E_PIN_AD_GPIO2 |<--jumper
+ * | LED_MOSI_A | E_PIN_AD_GPIO1 |<--jumper
+ * +------------+----------------+
+ */
+
+/* CC2650moda */
+
+/* Elite Pin for EIS1.1 Board */
+#define E_PIN_AD_GPIO2      DIO3
+#define E_PIN_AD_GPIO1      DIO4
+#define E_PIN_AD_CLK        DIO5
+#define E_PIN_AD_MOSI       DIO6
+#define E_PIN_AD_RST        DIO7
+#define E_PIN_MEM_CS        DIO8
+#define E_PIN_AD_CS         DIO10
+#define E_PIN_AD_GPIO0      DIO11
+#define E_PIN_BAT           DIO12
+#define E_PIN_AD_MISO       DIO1
+#define E_PIN_SHUT_DOWN     DIO14
+#define E_PIN_5V_ENABLE     PIN_UNASSIGNED
+
+#define E_PIN_LED_SCLK_A    DIO2
+#define E_PIN_LED_MOSI_A    DIO0
+
+/* SPI Board */
+#define Board_SPI0_MISO     PIN_UNASSIGNED
+#define Board_SPI0_MOSI     E_PIN_LED_MOSI_A
+#define Board_SPI0_CLK      E_PIN_LED_SCLK_A
+#define Board_SPI0_CS       PIN_UNASSIGNED
+
+#define Board_SPI1_MISO     E_PIN_AD_MISO
+#define Board_SPI1_MOSI     E_PIN_AD_MOSI
+#define Board_SPI1_CLK      E_PIN_AD_CLK
+#define Board_SPI1_CS       PIN_UNASSIGNED
+
+/* I2C */
+#define Board_I2C0_SCL0     PIN_UNASSIGNED
+#define Board_I2C0_SDA0     PIN_UNASSIGNED
+
+// delete in the future
+#define Turnon_I_LARGE      PIN_UNASSIGNED
+#define Turnon_I_MID        PIN_UNASSIGNED
+#define Turnon_I_SMALL      PIN_UNASSIGNED
+#define Turnon_V_MID        PIN_UNASSIGNED
+#define Turnon_V_SMALL      PIN_UNASSIGNED
+#define Turon_VOUT_SMALL    PIN_UNASSIGNED

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/boards_config/pin_def_eis11.h

@@ -0,0 +1,98 @@
+#ifndef PIN_DEF_EIS11_H
+#define PIN_DEF_EIS11_H
+
+#ifdef  __cplusplus
+extern "C" {
+#endif
+
+/*
+ * +------------------------------+
+ * |          CC2650moda          |
+ * +-------------+----------------+
+ * | MISO        | DIO1           |
+ * | D0          | DIO3           |
+ * | D1          | DIO4           |
+ * | D2/JTAG_TDO | DIO5/JTAG_TDO  |
+ * | D3/JTAG_TDI | DIO6/JTAG_TDI  |
+ * | D4          | DIO7           |
+ * | D5          | DIO8           |
+ * | D6          | DIO9           |
+ * | D7          | DIO10          |
+ * | LOAD2       | DIO11          |
+ * | LOAD1       | DIO12          |
+ * | LOAD0       | DIO13          |
+ * | SHUT_DOWN   | DIO14          |
+ * +-------------+----------------+
+ *
+ * +------------------------------------+
+ * | Elite Pin for ELITE_EIS_1_1 Board  |
+ * +------------+-----------------------+
+ * | AD_GPIO2   | D0                    |
+ * | AD_GPIO1   | D1                    |
+ * | AD_CLK     | D2                    |
+ * | AD_MOSI    | D3                    |
+ * | AD_RST     | D4                    |
+ * | MEM_CS     | D5                    |
+ * | 5V_ENABLE  | D6                    |
+ * | AD_CS      | D7                    |
+ * | AD_GPIO0   | LOAD2                 |
+ * | OFF        | LOAD0                 |<--OFF: shutdown_6994
+ * | AD_MISO    | MISO                  |
+ * | SHUT_DOWN  | SHUT_DOWN             |<--SHUT_DOWN: switch on/off
+ * +------------+-----------------------+
+ * | LED_SCLK_A | AD_GPIO2              |<--jumper
+ * | LED_MOSI_A | AD_GPIO1              |<--jumper
+ * +------------+-----------------------+
+ */
+
+/* CC2650moda */
+#define MISO            DIO1
+#define D0              DIO3
+#define D1              DIO4
+#define D2              DIO5
+#define D3              DIO6
+#define D4              DIO7
+#define D5              DIO8
+#define D6              DIO9
+#define D7              DIO10
+#define LOAD2           DIO11
+#define LOAD1           DIO12
+#define LOAD0           DIO13
+#define SHUT_DOWN       DIO14
+
+/* Elite Pin for ELITE_EIS_1_1 Board */
+#define E_PIN_AD_GPIO2      D0
+#define E_PIN_AD_GPIO1      D1
+#define E_PIN_AD_CLK        D2
+#define E_PIN_AD_MOSI       D3
+#define E_PIN_AD_RST        D4 //eis1.1-> use D4; eis1.0-> use LOAD0
+#define E_PIN_MEM_CS        D5
+#define E_PIN_5V_ENABLE     D6
+#define E_PIN_AD_CS         D7
+#define E_PIN_AD_GPIO0      LOAD2
+#define E_PIN_OFF           LOAD0
+#define E_PIN_AD_MISO       MISO
+#define E_PIN_SHUT_DOWN     SHUT_DOWN
+
+#define E_PIN_LED_SCLK_A    E_PIN_AD_GPIO2
+#define E_PIN_LED_MOSI_A    E_PIN_AD_GPIO1
+
+/* SPI Board */
+#define Board_SPI0_MISO     PIN_UNASSIGNED
+#define Board_SPI0_MOSI     E_PIN_LED_MOSI_A
+#define Board_SPI0_CLK      E_PIN_LED_SCLK_A
+#define Board_SPI0_CS       PIN_UNASSIGNED
+
+#define Board_SPI1_MISO     E_PIN_AD_MISO
+#define Board_SPI1_MOSI     E_PIN_AD_MOSI
+#define Board_SPI1_CLK      E_PIN_AD_CLK
+#define Board_SPI1_CS       PIN_UNASSIGNED
+
+/* I2C */
+#define Board_I2C0_SCL0     PIN_UNASSIGNED
+#define Board_I2C0_SDA0     PIN_UNASSIGNED
+
+#ifdef  __cplusplus
+}
+#endif
+#endif  // PIN_DEF_EIS11_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/driver/gpio_eis11.h

@@ -0,0 +1,14 @@
+#ifndef GPIO_EIS11_H
+#define GPIO_EIS11_H
+
+#ifdef  __cplusplus
+extern "C" {
+#endif
+
+uint8_t gpio_create(void);
+int8_t pin_set(uint8_t pin, uint8_t set_value);
+
+#ifdef  __cplusplus
+}
+#endif
+#endif  // GPIO_EIS11_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/driver/gpio_eis11_c.h

@@ -0,0 +1,58 @@
+#include "board.h"
+#include <ti/drivers/pin/PINCC26XX.h>
+#include "driver/gpio_eis11.h"
+
+static PIN_Handle   PinHandle;
+static PIN_State    PinStatus;
+
+const PIN_Config BLE_IO[] = {
+    E_PIN_5V_ENABLE | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,
+    E_PIN_AD_RST    | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL | PIN_DRVSTR_MAX,
+    E_PIN_AD_CS     | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL | PIN_DRVSTR_MAX,
+    E_PIN_OFF       | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL | PIN_DRVSTR_MAX, // E_PIN_OFF = 1: turn off 6994
+    E_PIN_SHUT_DOWN | PIN_INPUT_EN | PIN_PULLDOWN,
+
+    PIN_TERMINATE
+};
+
+static PIN_Handle __get_gpio_handle(void)
+{
+    return PinHandle;
+}
+
+static void __set_gpio_handle(PIN_Handle handle)
+{
+    PinHandle = handle;
+
+    return;
+}
+
+int8_t pin_set(uint8_t pin, uint8_t set_value)
+{
+    /*
+     * if status = 0: success
+     * else: fail
+     */
+    uint8_t p = pin;
+    uint8_t v = set_value;
+    PIN_Status status;
+
+    PIN_Handle handle = __get_gpio_handle();
+    status = PIN_setOutputValue(handle, p, v);
+
+    return status;
+}
+
+uint8_t gpio_create(void)
+{
+    PIN_Handle h;
+
+    h = PIN_open(&PinStatus, BLE_IO);
+    __set_gpio_handle(h);
+
+    if (h == NULL)
+        return 1;
+
+    return 0;
+}
+

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/driver/gpio_eis_mini10.h

@@ -0,0 +1,14 @@
+#ifndef GPIO_EIS_MINI10_H
+#define GPIO_EIS_MINI10_H
+
+#ifdef  __cplusplus
+extern "C" {
+#endif
+
+uint8_t gpio_create(void);
+int8_t pin_set(uint8_t pin, uint8_t set_value);
+
+#ifdef  __cplusplus
+}
+#endif
+#endif  // GPIO_EIS_MINI10_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/driver/gpio_eis_mini10_c.h

@@ -0,0 +1,57 @@
+#include "board.h"
+#include <ti/drivers/pin/PINCC26XX.h>
+#include "driver/gpio_eis_mini10.h"
+
+static PIN_Handle   PinHandle;
+static PIN_State    PinStatus;
+
+const PIN_Config BLE_IO[] = {
+    E_PIN_5V_ENABLE | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,
+    E_PIN_AD_RST    | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL | PIN_DRVSTR_MAX,
+    E_PIN_AD_CS     | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL | PIN_DRVSTR_MAX,
+    E_PIN_SHUT_DOWN | PIN_INPUT_EN | PIN_PULLDOWN,
+
+    PIN_TERMINATE
+};
+
+static PIN_Handle __get_gpio_handle(void)
+{
+    return PinHandle;
+}
+
+static void __set_gpio_handle(PIN_Handle handle)
+{
+    PinHandle = handle;
+
+    return;
+}
+
+int8_t pin_set(uint8_t pin, uint8_t set_value)
+{
+    /*
+     * if status = 0: success
+     * else: fail
+     */
+    uint8_t p = pin;
+    uint8_t v = set_value;
+    PIN_Status status;
+
+    PIN_Handle handle = __get_gpio_handle();
+    status = PIN_setOutputValue(handle, p, v);
+
+    return status;
+}
+
+uint8_t gpio_create(void)
+{
+    PIN_Handle h;
+
+    h = PIN_open(&PinStatus, BLE_IO);
+    __set_gpio_handle(h);
+
+    if (h == NULL)
+        return 1;
+
+    return 0;
+}
+

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/driver/spi_ctrl.h

@@ -0,0 +1,27 @@
+#ifndef SPI_CTRL_H
+#define SPI_CTRL_H
+
+#ifdef  __cplusplus
+extern "C" {
+#endif
+
+#define POL0    0
+#define POL1    1
+#define PHA0    0
+#define PHA1    1
+
+#define SPI_CLK_1M      1000000
+#define SPI_CLK_4M      4000000
+
+uint8_t spi0_open(uint32_t bitRate, uint8_t polarity, uint8_t phase);
+uint8_t spi0_close(void);
+uint8_t spi0_write(uint8_t *rxBuf, uint8_t *txBuf, uint8_t len);
+
+uint8_t spi1_open(uint32_t bitRate, uint8_t polarity, uint8_t phase);
+uint8_t spi1_close(void);
+uint8_t spi1_write(uint8_t *rxBuf, uint8_t *txBuf, uint8_t len);
+
+#ifdef  __cplusplus
+}
+#endif
+#endif  // SPI_CTRL_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/driver/spi_ctrl_c.h

@@ -0,0 +1,208 @@
+#include "board.h"
+#include <ti/drivers/SPI.h>
+#include "driver/spi_ctrl.h"
+
+#define CC2650_SPI_BITRATE_MAX  4000000     //4M
+
+static SPI_Handle SpiHandle0 = NULL;
+static SPI_Params SpiParams0;
+
+static SPI_Handle SpiHandle1 = NULL;
+static SPI_Params SpiParams1;
+
+static SPI_Handle __get_spi_handle(uint8_t spi_channel)
+{
+    uint8_t c = spi_channel;
+
+    if (c >= BOOSTXL_CC2650MA_SPICOUNT)
+        return NULL;
+
+    if (c == Board_SPI0)
+        return SpiHandle0;
+
+    if (c == Board_SPI1)
+        return SpiHandle1;
+
+    return 0;
+}
+
+static void __set_spi_handle(uint8_t spi_channel, SPI_Handle handle)
+{
+    uint8_t c = spi_channel;
+
+    if (c == Board_SPI0)
+        SpiHandle0 = handle;
+    else if (c == Board_SPI1)
+        SpiHandle1 = handle;
+
+    return;
+}
+
+static SPI_FrameFormat __get_spi_mode(uint8_t polarity, uint8_t phase)
+{
+    uint8_t pol = polarity;
+    uint8_t pha = phase;
+    SPI_FrameFormat mode;
+
+    if (pol == 0 && pha == 0)
+        mode = SPI_POL0_PHA0;
+    else if (pol == 0 && pha == 1)
+        mode = SPI_POL0_PHA1;
+    else if (pol == 1 && pha == 0)
+        mode = SPI_POL1_PHA0;
+    else if (pol == 1 && pha == 1)
+        mode = SPI_POL1_PHA1;
+
+    return mode;
+}
+
+uint8_t spi0_open(uint32_t bitRate, uint8_t polarity, uint8_t phase)
+{
+    uint32_t rate = bitRate;
+    uint8_t pol = polarity;
+    uint8_t pha = phase;
+    SPI_Handle h = __get_spi_handle(Board_SPI0);
+    SPI_Params *para = &SpiParams0;
+
+    if (rate > CC2650_SPI_BITRATE_MAX)
+        return 1;
+
+    if (pol > 1 || pha > 1)
+        return 2;
+
+    if (h != NULL)
+        return 3;
+
+    SPI_Params_init(para);
+    para->bitRate = rate;
+    para->mode = SPI_MASTER;
+    para->dataSize = 8;
+    para->frameFormat = __get_spi_mode(pol, pha);
+
+    h = SPI_open(Board_SPI0, para);
+    __set_spi_handle(Board_SPI0, h);
+
+    if (h == NULL)
+        return 4;
+
+    return 0;
+}
+
+uint8_t spi0_close(void)
+{
+    SPI_Handle h = __get_spi_handle(Board_SPI0);
+
+    if (h == NULL)
+        return 1;
+
+    SPI_close(h);
+    __set_spi_handle(Board_SPI0, NULL);
+
+    return 0;
+}
+
+uint8_t spi0_write(uint8_t *rxBuf, uint8_t *txBuf, uint8_t len)
+{
+    SPI_Handle h = __get_spi_handle(Board_SPI0);
+    SPI_Transaction spi0_tran;
+    uint8_t ret;
+
+    if (h == NULL)
+        return 1;
+
+    spi0_tran.count  = len;
+    spi0_tran.txBuf  = txBuf;
+    spi0_tran.arg    = NULL;
+    spi0_tran.rxBuf  = NULL;
+    ret = SPI_transfer(h, &spi0_tran);
+
+    if (ret == false)
+        return 2;
+
+    return 0;
+}
+
+uint8_t spi1_open(uint32_t bitRate, uint8_t polarity, uint8_t phase)
+{
+    uint32_t rate = bitRate;
+    uint8_t pol = polarity;
+    uint8_t pha = phase;
+    SPI_Handle h = __get_spi_handle(Board_SPI1);
+    SPI_Params *para = &SpiParams1;
+
+    if (rate > CC2650_SPI_BITRATE_MAX)
+        return 1;
+
+    if (pol > 1 || pha > 1)
+        return 2;
+
+    if (h != NULL)
+        return 3;
+
+    SPI_Params_init(para);
+    para->bitRate = rate;
+    para->mode = SPI_MASTER;
+    para->dataSize = 8;
+    para->frameFormat = __get_spi_mode(pol, pha);
+
+    h = SPI_open(Board_SPI1, para);
+    __set_spi_handle(Board_SPI1, h);
+
+    if (h == NULL)
+        return 4;
+
+    return 0;
+}
+
+uint8_t spi1_close(void)
+{
+    SPI_Handle h = __get_spi_handle(Board_SPI1);
+    if (h == NULL)
+        return 1;
+
+    SPI_close(h);
+    __set_spi_handle(Board_SPI1, NULL);
+
+    return 0;
+}
+
+uint8_t spi1_write(uint8_t *rxBuf, uint8_t *txBuf, uint8_t len)
+{
+    SPI_Handle h = __get_spi_handle(Board_SPI1);
+    SPI_Transaction spi1_tran;
+    uint8_t ret;
+
+    if (h == NULL)
+        return 1;
+
+    spi1_tran.count  = len;
+    spi1_tran.txBuf  = txBuf;
+    spi1_tran.arg    = NULL;
+    spi1_tran.rxBuf  = rxBuf;
+    ret = SPI_transfer(h, &spi1_tran);
+
+    if (ret == false)
+        return 2;
+
+    return 0;
+}
+
+/* utils.c.h */
+/*
+#include <stdio.h>
+#include <stdint.h>
+
+static void ___print_hex(uint8_t* p, int len)
+{
+    // ___print_hex((uint8_t *)p, sizeof(struct led_series_data_t));
+
+    int i;
+    
+    for (i = 0; i < len; i++) {
+        printf("0x%x, ", *p++);
+    }
+    printf("\n\n");
+    
+    return;
+}
+*/

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/driver/timers.h

@@ -0,0 +1,40 @@
+#ifndef TIMERS_H
+#define TIMERS_H
+
+#ifdef  __cplusplus
+extern "C" {
+#endif
+
+//timer
+enum gptimer0_ctrl_e {
+    GPT_CTRL_START = 0,
+    GPT_CTRL_STOP,
+    GPT_CTRL_CLOSE,
+
+    GPT_CTRL_MAX,
+};
+
+void elite_gptimer_open();
+uint8_t gptimer0_ctrl(enum gptimer0_ctrl_e gpt_ctrl);
+
+
+//clock
+/***************************************************
+ * Q: Why define CPU_1us = 16?
+ * A:
+ *   3 cycles per loop: 16 loops @ 48 Mhz ~= 1 us
+ *   3 cycles * X loops / 48Mhz = 1us(ideal value)
+ *   3 cycles * X loops / 48us = 1us(ideal value)
+ *   X = 48 / 3 => X = 16 loops
+ ***************************************************/
+#define CPU_1us     16
+#define CPU_1ms     16000
+
+void CPUdelay_us(uint32_t delay_t);
+void CPUdelay_ms(uint32_t delay_t);
+void GPT_timerIncrement();
+
+#ifdef  __cplusplus
+}
+#endif
+#endif  // TIMERS_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/driver/timers_c.h

@@ -0,0 +1,90 @@
+#include "board.h"
+#include <ti/drivers/timer/GPTimerCC26XX.h>
+#include <xdc/runtime/Types.h>
+#include <ti/sysbios/BIOS.h>
+#include "driver/timers.h"
+#include "simple_peripheral.h"
+
+static GPTimerCC26XX_Handle gptimer_handle; // was defined static
+
+#define CLOCK_FREQ 4769  // clock freq = 0.1 ms(4800), Measured(4769)
+
+static void elite_gptimer_callback(GPTimerCC26XX_Handle handle, GPTimerCC26XX_IntMask interruptMask) {
+    elite_gptimer_task();
+
+    return;
+}
+
+void elite_gptimer_open()
+{
+    GPTimerCC26XX_Params params;
+    GPTimerCC26XX_Params_init(&params);
+    params.width          = GPT_CONFIG_16BIT;
+    params.mode           = GPT_MODE_PERIODIC_UP;
+    params.debugStallMode = GPTimerCC26XX_DEBUG_STALL_OFF;
+    gptimer_handle = GPTimerCC26XX_open(Board_GPTIMER0A, &params);
+    if (gptimer_handle == NULL) {
+        Task_exit();
+    }
+    
+    Types_FreqHz  freq;
+    BIOS_getCpuFreq(&freq);
+    GPTimerCC26XX_Value loadVal = freq.lo / 1000 - 1; //47999 = 1ms
+    loadVal = CLOCK_FREQ; //0.1ms
+    GPTimerCC26XX_setLoadValue(gptimer_handle, loadVal);
+    GPTimerCC26XX_registerInterrupt(gptimer_handle, elite_gptimer_callback, GPT_INT_TIMEOUT);
+
+    GPTimerCC26XX_start(gptimer_handle);
+
+    return;
+}
+
+uint8_t gptimer0_ctrl(enum gptimer0_ctrl_e gpt_ctrl)
+{
+    enum gptimer0_ctrl_e gc = gpt_ctrl;
+    
+    if (gc > GPT_CTRL_MAX)
+        return 1;
+
+    switch (gc) {
+        case GPT_CTRL_START:
+            GPTimerCC26XX_start(gptimer_handle);
+            break;
+        
+        case GPT_CTRL_STOP:
+            GPTimerCC26XX_stop(gptimer_handle);
+            break;
+
+        case GPT_CTRL_CLOSE:
+            GPTimerCC26XX_close(gptimer_handle);
+            break;
+    }
+
+    return 0;
+}
+
+/*******************************************************************************************/
+//clock
+void CPUdelay_us(uint32_t delay_t)
+{
+    uint32_t t = delay_t;
+
+    CPUdelay(t * CPU_1us);
+
+    return;
+}
+
+void CPUdelay_ms(uint32_t delay_t)
+{
+    uint32_t t = delay_t;
+
+    CPUdelay(t * CPU_1ms);
+
+    return;
+}
+
+
+void GPT_timerIncrement() {
+    GPT.cnt_gpt_delta = GPT.cnt_gpt - GPT.cnt_gpt0;
+    GPT.cnt_gpt0 = GPT.cnt_gpt;
+}

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/elite_task/elite_GPtimer.h

@@ -0,0 +1,26 @@
+#ifndef ELITE_GPTIMER_H
+#define ELITE_GPTIMER_H
+
+#ifdef  __cplusplus
+extern "C" {
+#endif
+
+struct gptimer0_t{
+    uint32_t cnt_gpt;
+    uint32_t cnt_gpt0;
+    uint8_t  cnt_gpt_delta;
+    uint32_t cnt_adc_rate;
+    uint32_t cnt_notify_rate;
+    uint32_t cnt_v_scan_rate;
+    uint32_t cnt_lead_time;
+    uint32_t BatteryADCCounter;
+    uint32_t BatteryCheckCounter;
+    uint32_t GptimerMultiple;
+};
+
+void InitGPT();
+
+#ifdef  __cplusplus
+}
+#endif
+#endif  // ELITE_GPTIMER_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/elite_task/elite_GPtimer_c.h

@@ -0,0 +1,16 @@
+#include "elite_task/elite_GPtimer.h"
+
+void InitGPT()
+{
+    GPT.cnt_gpt = 0;
+    GPT.cnt_gpt0 = 0;
+    GPT.cnt_gpt_delta = 0;
+    GPT.cnt_adc_rate = 0;
+    GPT.cnt_notify_rate = 0;
+    GPT.cnt_v_scan_rate = 0;
+    GPT.cnt_lead_time = 0;
+    GPT.BatteryADCCounter = 0;
+    GPT.BatteryCheckCounter = 0;
+
+    return;
+}

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/hardware/led_APA_102.h

@@ -0,0 +1,97 @@
+#ifndef LED_APA_102_H
+#define LED_APA_102_H
+
+#ifdef  __cplusplus
+extern "C" {
+#endif
+
+/*
+ *  APA-102-2020-256-8A-20190612: Series data structure
+ *    +-------------------+------------------------- ... -+-----------------+
+ *    |  start_frame(4B)  |  led_frame(4B) *LED_TANDEM_N  |  end_frame(4B)  |
+ *    +-------------------+------------------------- ... -+-----------------+
+ *                       /                \
+ *                     /   led_frame(4B)   \
+ *                   /                      \
+ *       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+ *      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+ *      | 111 | bright  |      blue     |     green     |      red      |
+ *      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+ */
+
+#include "driver/spi_ctrl.h"
+
+#if (DEF_ELITE_MODEL == DEF_ELITE_EIS_11)
+    #define DEF_LED_TANDEN_N    12
+#elif (DEF_ELITE_MODEL == DEF_ELITE_EIS_MINI_10)
+    #define DEF_LED_TANDEN_N    1
+#endif
+
+#ifdef DEF_LED_TANDEN_N
+#define LED_TANDEM_N  DEF_LED_TANDEN_N
+#else
+#define LED_TANDEM_N  12
+#endif
+
+enum led_series_nb_e {
+    LED_NB_1 = 0,
+    LED_NB_2,
+    LED_NB_3,
+    LED_NB_4,
+    LED_NB_5,
+    LED_NB_6,
+    LED_NB_7,
+    LED_NB_8,
+    LED_NB_9,
+    LED_NB_10,
+    LED_NB_11,
+    LED_NB_12,
+    
+    LED_NB_MAX = LED_TANDEM_N,
+};
+
+enum led_bright_e {
+    LED_BR_LV0  = 0x00,
+    LED_BR_LV1  = 0x01,
+    LED_BR_LV8  = 0x08,
+
+    LED_BR_MAX  = 0x1F,
+};
+
+enum led_color_e {
+    LED_CLR_BLACK = 0,
+    LED_CLR_WHITE,
+    LED_CLR_RED,
+    LED_CLR_ORANGE,
+    LED_CLR_YELLOW,
+    LED_CLR_GREEN,
+    LED_CLR_CYAN,
+    LED_CLR_BLUE,
+    LED_CLR_PURPLE,
+    LED_CLR_MAGENTA,
+    LED_CLR_YELLOWGREEN,
+    LED_CLR_EMERALD,
+
+    LED_CLR_MAX,
+};
+
+struct led_color_t {
+    uint8_t b;
+    uint8_t g;
+    uint8_t r;    
+};
+
+struct led_frame_t {
+    uint8_t bright: 5,
+            rsvd: 3;
+    struct led_color_t color;
+};
+
+int led_color_set(enum led_series_nb_e led_nb, enum led_bright_e bright, enum led_color_e color);
+int led_color_code_set(enum led_series_nb_e led_nb, enum led_bright_e bright, struct led_color_t *color);
+int led_rainbow(enum led_bright_e bright);
+
+#ifdef  __cplusplus
+}
+#endif
+#endif  // LED_APA_102_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/hardware/led_APA_102_c.h

@@ -0,0 +1,189 @@
+#include "hardware/led_APA_102.h"
+
+#define LED_FRME_FILL_RSVD(_f)      (_f)->rsvd = 0x07 // 0x11100000 || bright
+#define LED_SERIES_D_START          0x00000000
+#define LED_SERIES_D_END            0xFFFFFFFF
+
+struct led_series_data_t {
+    uint32_t f_start;
+    struct led_frame_t f_led[LED_TANDEM_N];
+    uint32_t f_end;
+};
+
+static struct led_series_data_t led_series_data_g = {0};
+
+const struct led_color_t led_color_list_g[LED_CLR_MAX] = {
+//  {blue, green, red}
+    {0x00, 0x00, 0x00},     // LED_CLR_BLACK
+    {0xFF, 0xFF, 0xCA},     // LED_CLR_WHITE
+    {0x00, 0x00, 0xFF},     // LED_CLR_RED
+    {0x09, 0x58, 0xFF},     // LED_CLR_ORANGE
+    {0x00, 0xE1, 0xE1},     // LED_CLR_YELLOW
+    {0x00, 0xFA, 0x00},     // LED_CLR_GREEN
+    {0x40, 0x40, 0x00},     // LED_CLR_CYAN
+    {0xAA, 0x00, 0x00},     // LED_CLR_BLUE
+    {0x6F, 0x00, 0x3A},     // LED_CLR_PURPLE
+    {0xFF, 0x00, 0xFF},     // LED_CLR_MAGENTA
+    {0x00, 0xA6, 0x64},     // LED_CLR_YELLOWGREEN
+    {0x78, 0xC8, 0x50},     // LED_CLR_EMERALD
+};
+
+static int __led_single_set(struct led_series_data_t *led_s_d, struct led_frame_t *led_f, enum led_series_nb_e led_nb)
+{
+    struct led_series_data_t *sd = led_s_d;
+    struct led_frame_t *f = led_f;
+    enum led_series_nb_e nb = led_nb;
+    
+    memcpy(&sd->f_led[nb], f, sizeof(struct led_frame_t));
+
+    return 0;
+}
+
+static int __led_multiple_set(struct led_series_data_t *led_s_d, struct led_frame_t *led_f)
+{
+    struct led_series_data_t *sd = led_s_d;
+    struct led_frame_t *f = led_f;
+    int i;
+    
+    /*
+     * use __led_single_set() to finish all led;
+     */
+    for (i = LED_NB_1; i < LED_NB_MAX; i++) {
+        __led_single_set(sd, f, (enum led_series_nb_e)i);
+    }
+    
+    return 0;
+}
+
+static int __led_complete(struct led_series_data_t *led_s_d)
+{
+    struct led_series_data_t *sd = led_s_d;
+    struct led_frame_t *f = sd->f_led;
+    int i;
+
+    for (i = LED_NB_1; i < LED_NB_MAX; i++) {
+        LED_FRME_FILL_RSVD(f);
+        f++;
+    }
+
+    sd->f_start = LED_SERIES_D_START;
+    sd->f_end   = LED_SERIES_D_END;
+    
+    return 0;
+}
+
+static int __led_color_set(enum led_series_nb_e led_nb, struct led_frame_t *led_f)
+{
+    enum led_series_nb_e nb = led_nb;
+    struct led_frame_t *f = led_f;
+    struct led_series_data_t *sd = &led_series_data_g;
+
+    if (f == NULL)
+        return -1;
+
+    /*
+     * nb -  < LED_NB_MAX: fill one led_frame
+     *      == LED_NB_MAX: fill multiple led_frame
+     *
+     * complete: then, fill (start_frame, end_frame and the rsvd of every led_frame)
+     *
+     * finally, write cmd to hw by spi
+     */
+    if (nb < LED_NB_MAX) {
+        __led_single_set(sd, f, nb);
+    } else if (nb == LED_NB_MAX) {
+        __led_multiple_set(sd, f);
+    } else {
+        return -2;
+    }
+
+    __led_complete(sd);
+    
+#define WRITE_TO_HW(_d, _l) spi0_write(NULL, (uint8_t *)(_d), (_l))
+    WRITE_TO_HW(sd, sizeof(struct led_series_data_t));
+
+    return 0;
+}
+
+int led_color_set(enum led_series_nb_e led_nb, enum led_bright_e bright, enum led_color_e color)
+{
+    enum led_series_nb_e nb = led_nb;
+    enum led_bright_e b = bright;
+    enum led_color_e c = color;
+    struct led_frame_t led_f;
+    
+    if (nb > LED_NB_MAX)
+        return -1;
+
+    if (c >= LED_CLR_MAX)
+        return -2;
+    
+    if (b > LED_BR_MAX)
+        return -3;
+    
+    led_f.bright = b;
+    led_f.color = led_color_list_g[c];
+    __led_color_set(nb, &led_f);
+
+    return 0;
+}
+
+int led_color_code_set(enum led_series_nb_e led_nb, enum led_bright_e bright, struct led_color_t *color)
+{
+    enum led_series_nb_e nb = led_nb;
+    enum led_bright_e b = bright;
+    struct led_color_t *c = color;
+    struct led_frame_t led_f;
+    
+    // valid the input values
+    if (nb > LED_NB_MAX)
+        return -1;
+
+    if (b > LED_BR_MAX)
+        return -2;
+    
+    led_f.bright = b;
+    memcpy(&led_f.color, c, sizeof(struct led_color_t));
+
+    __led_color_set(nb, &led_f);
+
+    return 0;
+}
+
+int led_rainbow(enum led_bright_e bright)
+{
+    enum led_bright_e b = bright;
+    int i;
+    
+    if (b > LED_BR_MAX)
+        return -1;
+    
+    for(i=0; i<LED_NB_MAX; i++) {
+        led_color_set((enum led_series_nb_e)i, b, (enum led_color_e)i);
+    }
+    
+    return 0;
+}
+
+/*
+ * example -
+ *    customize color:
+ *        struct led_color_t led_c; 
+ *        uint8_t bri;
+ *                       // { ins,  ins,      num,    r,    g,    b,  bri};
+ *        uint8_t ins[20] = {0x30, 0x00, LED_NB_4, 0xFF, 0x00, 0x44,  0x3};  
+ *        led_c.r = ins[3];
+ *        led_c.g = ins[4];
+ *        led_c.b = ins[5];
+ *        bri = ins[6];   
+ *        led_color_code_set(LED_NB_4, bri, &led_c);
+ *
+ *    single led:
+ *        led_color_set(LED_NB_1, LED_BR_LV1, LED_CLR_WHITE);
+ * 
+ *    multiple led:
+ *        led_color_set(LED_NB_MAX, LED_BR_LV1, LED_CLR_BLUE);
+ * 
+ *    rainbow led:
+ *        led_rainbow(LED_BR_LV1);
+ */

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/AD5940.h

@@ -0,0 +1,137 @@
+
+#ifndef AD5940
+#define AD5940
+
+#define NV2USC(_n) (n / 1e7 * 625 + 25000) // [5nV] / 1e6 * 5 * 12.5 + 25000
+
+static void setEIS_EIS_cali(void)
+{
+    AD5940_SPIWriteReg(LPDACCON0, 0x00000001); // Direct from LPDACDAT0 | Vzero(6bit) & Vbias(12bit) | LP 2.5v as ref
+    AD5940_SPIWriteReg(LPDACSW0, 0b111111); // orverride LPDACCON0[5] | LPDACSW0[0~5] close
+
+    AD5940_SPIWriteReg(HSRTIACON, 0x00000000); // CTIA=1pF | SW6 off(open) | RTIA=200R
+    AD5940_SPIWriteReg(HSTIACON, 0x00000001); // Vzero
+
+    AD5940_SPIWriteReg(ADCCON, 0x00000101); // PGA=1 | HSTIA neg input | HSTIA pos signal
+    AD5940_SPIWriteReg(DFTCON, 0x00000091); // DFTNUM=2048 | enable hanning window | SINC2
+    AD5940_SPIWriteReg(SWCON, 0x00026355); // D5 | P5 | N3 | T6 | T9 close
+
+    if (instru.gain_lv_hstia < HSRTIA_MAX) {
+        instru.HSTIAAutoGainEnable = 0;
+        HSTIAGainCtrl(instru.gain_lv_hstia);
+    } else {
+        instru.HSTIAAutoGainEnable = 1;
+        instru.gain_lv_hstia = HSRTIA_200R;
+        HSTIAGainCtrl(instru.gain_lv_hstia);
+    }
+
+    int32_t LPVolt = 0;
+    LPVolt = (instru.dcbias - 25000) * 4 * 4000;
+    DAC_outputV(LPVolt);
+    cali_SetWGAmp(instru.acamp);
+
+    AD5940_SPIWriteReg(AFECON, 0x0031CFC0); // en dc DAC buf | HSDAC ref disable | LDO buf current limit enable | en SINC2 |
+                                            // DFT hardware accelerator enable | waveform generator enable | HSTIA enable |
+                                            // intru amplifier enable | excitation buf enable | ADC conversions enable |
+                                            // ADC power enable | HSDAC enable | HP ref enable
+
+    //HIGH POWER MODE
+    AD5940_SPIWriteReg(PMBW, 0x0000000D); // HS mode | Set cutooff frequency to 250kHz, -3 dB bandwidth
+    AD5940_SPIWriteReg(CLKSEL, 0x0000);
+    AD5940_SPIWriteReg(CLKCON0KEY, 0xA815); // !!!Write 0xA815 to this register before accessing the CLKCON0 register
+    AD5940_SPIWriteReg(CLKCON0, 0x0442);    //6bit system clock divider //set divider = 2
+    AD5940_SPIWriteReg(HSOSCCON, 0x00000000); // HP osc select 32MHz output
+    AD5940_SPIWriteReg(ADCFILTERCON, 0x00000311); // en DFT clk | en DAC wave clk | en SINC2 filter clk | 2 ADC samples used for average function |
+                                                  // SINC3 filter oversampling rate is 800kSPS |
+                                                  // SINC2 filter oversampling rate is 178 samples |
+                                                  // disable average | SINC3 filter enable |
+                                                  // Bypass 50/60Hz | ADC data rate 800kHz 
+    AD5940_SPIWriteReg(HSDACCON, 0x0000000E); // HSDAC gain = 2, DAC update rate = ACLK/HSDACCON = 32Mhz/7
+    AD5940_SPIWriteReg(ADCBUFCON, 0x005F3D0F); //recommended
+    SetEISHIGHZ(0);
+}
+
+static void setEIS_CV (void)
+{
+   //Clock and Ref
+    AD5940_SPIWriteReg(CLKSEL, 0x0);
+    AD5940_SPIWriteReg(HSOSCCON, 0x00000004); //16 MHz output
+    AD5940_SPIWriteReg(0x2180, 0x00000037); //0b110110
+
+    //Configure LPDAC LPTIA
+    AD5940_SPIWriteReg(LPREFBUFCON, 0x0); //enable lpref and lp 2.5V buffer
+    AD5940_SPIWriteReg(LPDACSW0, 0x00000034); // disconnect Vbias and Vzero
+
+    AD5940_SPIWriteReg(LPTIASW0, 0x00000034); // SW2 | SW4 | SW5
+
+    LPTIAGainCtrl(instru.gain_lv_lptia);
+    AD5940_SPIWriteReg(LPDACCON0, 0x00000001);
+
+    //Configure ADC | ADCDAT (0x2074)
+    AD5940_SPIWriteReg(ADCCON, 0x00010221); //PGA = 1.5 | LPTIA- | LPTIA_OUT
+
+    AD5940_SPIWriteReg(ADCFILTERCON, 0x00002011); // Sinc3 En | SINC3OSR2 | SINC2OSR22
+    AD5940_SPIWriteReg(DFTCON, 0x00000001); // Sinc2 to DFT | DFTNUM4
+
+    // mean function for calibration
+    AD5940_SPIWriteReg(RRR_AFE_STATSCON, 0x00000001);       // don't use mean function // dev | 128 samples | enable statistics
+
+    //AFE and PWMB
+    AD5940_SPIWriteReg(AFECON, 0x00098780); //ADC on //0b10011000011110000000
+    AD5940_SPIWriteReg(PMBW, 0x00000005); //fc 50kHz, low power mode
+}
+
+static void set_hs_only(void)
+{
+    AD5940_SPIWriteReg(LPDACCON0, 0x00000001); // Direct from LPDACDAT0 | Vzero(6bit) & Vbias(12bit) | LP 2.5v as ref
+    AD5940_SPIWriteReg(LPDACSW0, 0b111111); // orverride LPDACCON0[5] | LPDACSW0[0~5] close
+
+    AD5940_SPIWriteReg(HSRTIACON, 0x00000000); // CTIA=1pF | SW6 off(open) | RTIA=200R
+    AD5940_SPIWriteReg(HSTIACON, 0x00000001); // Vzero
+
+    AD5940_SPIWriteReg(ADCCON, 0x00000101); // PGA=1 | HSTIA neg input | HSTIA pos signal
+    AD5940_SPIWriteReg(DFTCON, 0x00000091); // DFTNUM=2048 | enable hanning window | SINC2
+    AD5940_SPIWriteReg(SWCON, 0x00026355); // D5 | P5 | N3 | T6 | T9 close
+
+    AD5940_SPIWriteReg(AFECON, 0x0031CFC0); // en dc DAC buf | HSDAC ref disable | LDO buf current limit enable | en SINC2 |
+                                            // DFT hardware accelerator enable | waveform generator enable | HSTIA enable |
+                                            // intru amplifier enable | excitation buf enable | ADC conversions enable |
+                                            // ADC power enable | HSDAC enable | HP ref enable
+
+    //HIGH POWER MODE
+    AD5940_SPIWriteReg(PMBW, 0x0000000D); // HS mode | Set cutooff frequency to 250kHz, -3 dB bandwidth
+    AD5940_SPIWriteReg(CLKSEL, 0x0000);
+    AD5940_SPIWriteReg(CLKCON0KEY, 0xA815); // !!!Write 0xA815 to this register before accessing the CLKCON0 register
+    AD5940_SPIWriteReg(CLKCON0, 0x0442);    //6bit system clock divider //set divider = 2
+    AD5940_SPIWriteReg(HSOSCCON, 0x00000000); // HP osc select 32MHz output
+    AD5940_SPIWriteReg(ADCFILTERCON, 0x00000311); // en DFT clk | en DAC wave clk | en SINC2 filter clk | 2 ADC samples used for average function |
+                                                  // SINC3 filter oversampling rate is 800kSPS |
+                                                  // SINC2 filter oversampling rate is 178 samples |
+                                                  // disable average | SINC3 filter enable |
+                                                  // Bypass 50/60Hz | ADC data rate 800kHz 
+    AD5940_SPIWriteReg(HSDACCON, 0x0000000E); // HSDAC gain = 2, DAC update rate = ACLK/HSDACCON = 32Mhz/7
+    AD5940_SPIWriteReg(ADCBUFCON, 0x005F3D0F); //recommended
+    SetEISHIGHZ(0);
+
+    return;
+}
+
+// static void AD5940_Initialize() {
+//     AD5940_SPIWriteReg(0x0908, 0x02C9);//initiation
+//     AD5940_SPIWriteReg(0x0C08, 0x206C);
+//     AD5940_SPIWriteReg(0x21F0, 0x0010);
+//     AD5940_SPIWriteReg(0x0410, 0x02C9);
+//     AD5940_SPIWriteReg(0x0A28, 0x0009);
+//     AD5940_SPIWriteReg(ADCBUFCON, 0x0104);
+//     AD5940_SPIWriteReg(0x0A04, 0x4859);
+//     AD5940_SPIWriteReg(0x0A04, 0xF27B);
+//     AD5940_SPIWriteReg(0x0A00, 0x8009);
+//     AD5940_SPIWriteReg(PMBW, 0x0000);
+// }
+
+// static void AD5940_sftreset(){
+//     AD5940_SPIWriteReg(0x0424, 0xA158);
+//     CPUdelay_us(200);
+// }
+
+#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/Elite.json

@@ -1,179 +0,0 @@
-{
-  "name": "Elite-ZM",
-  "version": "1.2.30",
-  "match_rule": {
-    "local_name_pattern": "Elite-ZM.+",
-    "major_product_number": 0,
-    "minor_product_number": 2,
-    "major_version_number": 1,
-    "minor_version_number": 2
-  },
-  "constant": {
-    "ADC_CHANNEL_NUMBER": [
-      12,
-      13,
-      14,
-      15
-    ],
-    "VOLT_MAX": 4095
-  },
-  "parameters": {
-    "CHANNEL": {
-      "description": "record channels",
-      "record_meta": true,
-      "domain": "property",
-      "value": [
-        0,
-        1,
-        2
-      ]
-    },
-    "SAMPLE_RATE": {
-      "description": "data sampling rate",
-      "record_meta": true,
-      "domain": "constant",
-      "value": 1
-    },
-    "AMP_GAIN": {
-      "description": "amp gain",
-      "record_meta": true,
-      "domain": "constant",
-      "value": 1
-    },
-    "MODE": {
-      "description": "working mode",
-      "value": [
-        "I-V Curve",
-        "Cyclic Voltammetry",
-        "Function Generator",
-        "Z-T Curve",
-        "V-T Curve",
-        "I-T Curve",
-        "ADC test"
-      ]
-    },
-    "VOLT_ORIGIN": {
-      "description": "Origin Voltage of Scan",
-      "domain": [
-        "VOLT_MAX"
-      ]
-    },
-    "VOLT_FINAL": {
-      "description": "The last Voltage of Scan",
-      "domain": [
-        "VOLT_MAX"
-      ],
-      "value": "1365 * VALUE"
-    },
-    "VOLT_STEP": {
-      "description": "Voltage Step",
-      "domain": [
-        5
-      ]
-    },
-    "STEP_TIME": {
-      "description": "How much time between two step",
-      "domain": [
-        4
-      ]
-    },
-    "DAC_VOLT": {
-      "description": "DAC output Voltage",
-      "domain": [
-        "VOLT_MAX"
-      ]
-    },
-    "ADC_CHANNEL": {
-      "description": "read ADC data",
-      "value": [
-        "ANA0",
-        "ANA1",
-        "ANA2",
-        "ANA3"
-      ]
-    }
-  },
-  "instruction": {
-    "start": [
-      {
-        "expression": "MODE",
-        "when": {
-          "0": "curve_iv",
-          "1": "curve_cv",
-          "2": "func_gen",
-          "6": "adc_test"
-        }
-      }
-    ],
-    "data_format": [
-      "_data_format('TDC4VAF2')"
-    ],
-    "curve_iv": [
-      "data_format",
-      "_notify(True)",
-      "curve_iv0",
-      "_sync(True)",
-      "VIS_STI"
-    ],
-    "curve_iv0": {
-      "type": "RIS",
-      "parameter": {
-        "va": "(VOLT_ORIGIN + 1) * 0x0010",
-        "vb": "(VOLT_FINAL + 1) * 0x0010",
-        "dv": "VOLT_STEP * 0x40",
-        "dt": "STEP_TIME * 0x12"
-      },
-      "data": [
-        "1X10;2B>va;2B>vb;B>dv;B>dt"
-      ]
-    },
-    "curve_cv": [
-      "data_format",
-      "_notify(True)",
-      "curve_cv0",
-      "_sync(True)",
-      "VIS_STI"
-    ],
-    "curve_cv0": {
-      "type": "RIS",
-      "parameter": {
-        "va": "(VOLT_ORIGIN + 1) * 0x0010",
-        "vb": "(VOLT_FINAL + 1) * 0x0010",
-        "dv": "VOLT_STEP * 0x40",
-        "dt": "STEP_TIME * 0x12"
-      },
-      "data": [
-        "1X20;2B>va;2B>vb;B>dv;B>dt"
-      ]
-    },
-    "func_gen": [
-      "data_format",
-      "func_gen0",
-      "VIS_STI"
-    ],
-    "func_gen0": {
-      "type": "RIS",
-      "parameter": {
-        "v": "(DAC_VOLT + 1) * 0x0010"
-      },
-      "data": [
-        "X30;X30;2B>v"
-      ]
-    },
-    "adc_test": [
-      "data_format",
-      "_notify(True)",
-      "adc_test0",
-      "_sync(True)",
-      "VIS_STI"
-    ],
-    "adc_test0": {
-      "type": "RIS",
-      "data": [
-        "X90;B>ADC_CHANNEL"
-      ]
-    }
-  }
-}
-
-

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/Elite15_PIN.h

@@ -1,246 +0,0 @@
-
-#ifndef Elite15_PIN
-#define Elite_15PIN
-
-#include "Elite_PIN.h"
-
-static void update_latch_status (uint32_t latch_num, uint32_t elite_pin, bool highlow) {
-    switch (latch_num) {
-        case LOAD0: {
-            switch (elite_pin) {
-                case D0: {
-                    LH.LATCH0[0] = highlow;
-                    break;
-                }
-                case D1: {
-                    LH.LATCH0[1] = highlow;
-                    break;
-                }
-                case D2: {
-                    LH.LATCH0[2] = highlow;
-                    break;
-                }
-                case D3: {
-                    LH.LATCH0[3] = highlow;
-                    break;
-                }
-                case D4: {
-                    LH.LATCH0[4] = highlow;
-                    break;
-                }
-                case D5: {
-                    LH.LATCH0[5] = highlow;
-                    break;
-                }
-                case D6: {
-                    LH.LATCH0[6] = highlow;
-                    break;
-                }
-                case D7: {
-                    LH.LATCH0[7] = highlow;
-                    break;
-                }
-                default: {
-                    break;
-                }
-            }
-            break;
-        }
-        case LOAD1: {
-            switch (elite_pin) {
-                case D0: {
-                    LH.LATCH1[0] = highlow;
-                    break;
-                }
-                case D1: {
-                    LH.LATCH1[1] = highlow;
-                    break;
-                }
-                case D2: {
-                    LH.LATCH1[2] = highlow;
-                    break;
-                }
-                case D3: {
-                    LH.LATCH1[3] = highlow;
-                    break;
-                }
-                case D4: {
-                    LH.LATCH1[4] = highlow;
-                    break;
-                }
-                case D5: {
-                    LH.LATCH1[5] = highlow;
-                    break;
-                }
-                case D6: {
-                    LH.LATCH1[6] = highlow;
-                    break;
-                }
-                case D7: {
-                    LH.LATCH1[7] = highlow;
-                    break;
-                }
-                default: {
-                    break;
-                }
-            }
-            break;
-        }
-        case LOAD2: {
-            switch (elite_pin) {
-                case D0: {
-                    LH.LATCH2[0] = highlow;
-                    break;
-                }
-                case D1: {
-                    LH.LATCH2[1] = highlow;
-                    break;
-                }
-                case D2: {
-                    LH.LATCH2[2] = highlow;
-                    break;
-                }
-                case D3: {
-                    LH.LATCH2[3] = highlow;
-                    break;
-                }
-                case D4: {
-                    LH.LATCH2[4] = highlow;
-                    break;
-                }
-                case D5: {
-                    LH.LATCH2[5] = highlow;
-                    break;
-                }
-                case D6: {
-                    LH.LATCH2[6] = highlow;
-                    break;
-                }
-                case D7: {
-                    LH.LATCH2[7] = highlow;
-                    break;
-                }
-                default: {
-                    break;
-                }
-            }
-             break;
-        }
-        default: {
-            break;
-        }
-    }
-}
-
-static void PIN15_setOutputValue (uint32_t latch_num, uint32_t pin_num, bool highlow) {
-    ELITE15_SPI_CLOSE();
-    add_elite_pin();
-    update_latch_status (latch_num, pin_num, highlow);
-//    PIN_setOutputValue(&ZM_rst, latch_num, 1);               // Turn on latch
-
-    switch (latch_num) {
-        case LOAD0: {
-//            PIN_setOutputValue(&ZM_rst, D0, LH.LATCH0[0]);
-//            PIN_setOutputValue(&ZM_rst, D1, LH.LATCH0[1]);
-//            PIN_setOutputValue(&ZM_rst, D2, LH.LATCH0[2]);
-//            PIN_setOutputValue(&ZM_rst, D3, LH.LATCH0[3]);
-            PIN_setOutputValue(pin_handle, D4, LH.LATCH0[4]);
-            PIN_setOutputValue(pin_handle, D5, LH.LATCH0[5]);
-            PIN_setOutputValue(pin_handle, D6, LH.LATCH0[6]);
-            PIN_setOutputValue(pin_handle, D7, LH.LATCH0[7]);
-            break;
-        }
-        case LOAD1: {
-            PIN_setOutputValue(pin_handle, D0, LH.LATCH1[0]);
-            PIN_setOutputValue(pin_handle, D1, LH.LATCH1[1]);
-            PIN_setOutputValue(pin_handle, D2, LH.LATCH1[2]);
-            PIN_setOutputValue(pin_handle, D3, LH.LATCH1[3]);
-            PIN_setOutputValue(pin_handle, D4, LH.LATCH1[4]);
-            PIN_setOutputValue(pin_handle, D5, LH.LATCH1[5]);
-            PIN_setOutputValue(pin_handle, D6, LH.LATCH1[6]);
-            PIN_setOutputValue(pin_handle, D7, LH.LATCH1[7]);
-            break;
-        }
-        case LOAD2: {
-            PIN_setOutputValue(pin_handle, D0, LH.LATCH2[0]);
-            PIN_setOutputValue(pin_handle, D1, LH.LATCH2[1]);
-            PIN_setOutputValue(pin_handle, D2, LH.LATCH2[2]);
-            PIN_setOutputValue(pin_handle, D3, LH.LATCH2[3]);
-            PIN_setOutputValue(pin_handle, D4, LH.LATCH2[4]);
-            PIN_setOutputValue(pin_handle, D5, LH.LATCH2[5]);
-            PIN_setOutputValue(pin_handle, D6, LH.LATCH2[6]);
-            PIN_setOutputValue(pin_handle, D7, LH.LATCH2[7]);
-            break;
-        }
-        default: {
-            break;
-        }
-    }
-    PIN_setOutputValue(&ZM_rst, latch_num, 1);               // Turn on latch
-//    CPUdelay(10);
-    PIN_setOutputValue(&ZM_rst, latch_num, 0);               // Turn off latch
-    remove_elite_pin();
-    ELITE15_SPI_HOLD();
-}
-
-static void Init_Elite15_PIN () {
-    InitLH();
-    add_elite_pin();
-
-    PIN_setOutputValue(pin_handle, D0, 0);
-    PIN_setOutputValue(pin_handle, D1, 0);
-    PIN_setOutputValue(pin_handle, D2, 0);
-    PIN_setOutputValue(pin_handle, D3, 0);
-    PIN_setOutputValue(pin_handle, D4, 0);
-    PIN_setOutputValue(pin_handle, D5, 0);
-    PIN_setOutputValue(pin_handle, D6, 0);
-    PIN_setOutputValue(pin_handle, D7, 0);
-    PIN_setOutputValue(pin_handle, LOAD0, 0);
-    PIN_setOutputValue(pin_handle, LOAD1, 1);
-    PIN_setOutputValue(pin_handle, LOAD2, 1);
-    CPUdelay(10);
-    PIN_setOutputValue(pin_handle, LOAD1, 0);
-    PIN_setOutputValue(pin_handle, LOAD2, 0);
-
-
-    PIN_setOutputValue(pin_handle, D0, 0);
-    PIN_setOutputValue(pin_handle, D1, 0);
-    PIN_setOutputValue(pin_handle, D2, 0);
-    PIN_setOutputValue(pin_handle, D3, 0);
-    PIN_setOutputValue(pin_handle, D4, 1);
-    PIN_setOutputValue(pin_handle, D5, 1);
-    PIN_setOutputValue(pin_handle, D6, 1);
-    PIN_setOutputValue(pin_handle, D7, 1);
-    CPUdelay(10);
-    PIN_setOutputValue(pin_handle, LOAD0, 1);
-    PIN_setOutputValue(pin_handle, LOAD0, 0);
-
-    remove_elite_pin();
-
-//    InitLH();
-//    add_elite_pin();
-//
-//    PIN_setOutputValue(pin_handle, LOAD0, 1);
-//    PIN_setOutputValue(pin_handle, LOAD1, 1);
-//    PIN_setOutputValue(pin_handle, LOAD2, 1);
-//    CPUdelay(10);
-//    PIN_setOutputValue(pin_handle, D0, 0);
-//    PIN_setOutputValue(pin_handle, D1, 0);
-//    PIN_setOutputValue(pin_handle, D2, 0);
-//    PIN_setOutputValue(pin_handle, D3, 0);
-//    PIN_setOutputValue(pin_handle, D4, 0);
-//    PIN_setOutputValue(pin_handle, D5, 0);
-//    PIN_setOutputValue(pin_handle, D6, 0);
-//    PIN_setOutputValue(pin_handle, D7, 0);
-//    CPUdelay(10);
-//    PIN_setOutputValue(pin_handle, LOAD0, 0);
-//    PIN_setOutputValue(pin_handle, LOAD1, 0);
-//    PIN_setOutputValue(pin_handle, LOAD2, 0);
-//
-//    remove_elite_pin();
-}
-
-
-
-
-#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteDAC.h

@@ -4,60 +4,203 @@
 
 static bool DACReset;
 
-#ifdef ELITE_VERSION_1_4
-#define DACCLS 0x02
-#define DACOUT 0x31
+#define VBIAS_LSB       107422          // 2200/4096 [mV] = 107422 [5nV]
+#define VZERO_LSB       6875008         // VBIAS_LSB * 64
+#define DAC12BIT_LSB    107422
 
-static uint16_t DAC_outputV(uint16_t voltLV) {
-    // C = command, X = don't care, D = data
-    // CCCC CCCC = command
-    // DDDD DDDD = v1
-    // DDDD DDDD = v2
+#define VOLT_MV_TO_5NV(_v)  (_v * 200000)
+#define V_5nV(_v)   VOLT_MV_TO_5NV(_v)
 
-    // command
-    // 0x02 = clear
-    // 0x31 = output voltage
 
-    uint8_t v1, v2 = 0;
-    v1 = (uint8_t) ((voltLV & 0xFF00) >> 8);
-    v2 = (uint8_t) (voltLV & 0x00FF);
+/* user code: 0 ~ 35000; LPDAC bias value: -1.5V ~ +1.5V */
+static int32_t DAC_outputV(int32_t voltLVraw) {   // LPDAC output, voltLV = Vbias-Vzero
+    /* new code*/
+    int32_t ret;
+    int32_t vscan;
+    int64_t v_z;
+    int64_t v_zero;
+    int64_t v_bias;
+    uint8_t n_zero;//6btit
+    uint16_t n_bias;//12bit
+    uint32_t DACOutCode;
 
-    spi_DACtxbuf[0] = DACOUT;
-    spi_DACtxbuf[1] = v1;
-    spi_DACtxbuf[2] = v2;
+    vscan = voltLVraw * (-1);
 
-    DAC_SPI(SPI_DAC_SIZE, spi_DACtxbuf, spi_rxbuf);
+    v_z = (V_5nV(2200) - (int64_t)vscan) * 200000 / 431579 + V_5nV(200);     // v_z = (V_5nV(2200) - vscan)/2.157895 + V_5nV(200);
+    n_zero = v_z * 100 / V_5nV(3438);                                        // n_zero = v_z / V_5nV(34.38);
+    v_zero = (int64_t)n_zero * V_5nV(3438) / 100;                            // v_zero = n_zero * V_5nV(34.38);
+                                                                             //
+    if (vscan < 0) {                                                         //
+        v_zero -= V_5nV(5372) / 10000;                                       // v_zero -= V_5nV(0.5372);
+    }                                                                        //
+                                                                             //
+    v_bias = vscan + v_zero;                                                 // v_bias = vscan + v_zero;
+    n_bias = v_bias * 10000 / V_5nV(5372);                                   // n_bias = v_bias / V_5nV(0.5372);
 
-    return voltLV;
+    while (n_bias > 4095) {
+        n_zero--;
+        v_zero = (int64_t)n_zero * V_5nV(3438) / 100;
+
+        if (vscan < 0) {
+            v_zero -= V_5nV(5372) / 10000;
+        }
+
+        v_bias = vscan + v_zero;
+        n_bias = v_bias * 10000 / V_5nV(5372);
+
+        if ((n_bias <= 4095) || ( n_bias > 4095 && n_zero > 63))
+            break;
+    }
+
+    if(n_bias > 4095) n_bias = 4095;
+    if(n_zero >   63) n_zero =   63;
+    DACOutCode = (0x0003FFFF & ((n_zero << 12) + n_bias));
+
+    AD5940_SPIWriteReg(LPDACDAT0, DACOutCode);
+
+    ret = (int32_t)(v_bias - v_zero);  //vscan
+
+
+    return ret;
+}
+
+/* user code: 0 ~ 50000: -2V ~ +2V */
+static void HSDAC_outputV(int32_t voltLVraw)
+{
+    uint8_t n_zero;//6btit
+    uint16_t n_bias;//12bit
+    uint32_t DACOutCode;
+    int64_t value = ((int64_t)voltLVraw * voltLVraw * CaliTable.ac_dcbais.up_a + voltLVraw * CaliTable.ac_dcbais.up_b + CaliTable.ac_dcbais.up_c + 5e11) / 1e12;
+    if ( value < 1920) 
+        value = ((int64_t)voltLVraw * voltLVraw * CaliTable.ac_dcbais.down_a + voltLVraw * CaliTable.ac_dcbais.down_b + CaliTable.ac_dcbais.down_c + 5e11) / 1e12;
+    n_zero = 30;
+    n_bias = (uint16_t)value;
+
+    if(n_bias > 4095) n_bias = 4095;
+    if(n_zero >   63) n_zero =   63;
+    DACOutCode = (0x0003FFFF & ((n_zero << 12) + n_bias));
+
+    AD5940_SPIWriteReg(LPDACDAT0, DACOutCode);
+
+    return;
+}
+
+/* user code: 0 ~ 50000; LPDAC bias value: -2V ~ +2V */
+static void set_lpdac_ce_1100mv(uint8_t z, uint16_t b) {   // LPDAC output, voltLV = Vbias-Vzero
+    /* new code*/
+    uint8_t n_zero = z;//6btit
+    uint16_t n_bias = b;//12bit
+    uint32_t DACOutCode;
+
+    DACOutCode = (0x0003FFFF & ((n_zero << 12) + n_bias));
+
+    AD5940_SPIWriteReg(LPDACDAT0, DACOutCode);
+
+    return;
+}
+
+static uint32_t DAC_outputF(uint32_t freq) {
+    AD5940_SPIWriteReg(WGFCW, freq);
+    return freq;
 }
 
 static void VoutGainControl(uint8_t VOUTLevel){
-    if(VOUTLevel == 0){
-        // VOUT gain level = 0, using 240K resister
-        PIN15_setOutputValue(Turnon_VOUT_SMALL, 0);
-    }
-    else if(VOUTLevel == 1){
-        // VOUT gain level = 1, using 15K resister
-        PIN15_setOutputValue(Turnon_VOUT_SMALL, 1);
-    }
-    else if(VOUTLevel == 2){
-        // VOUT gain level = 2, using 15K resister
-        PIN15_setOutputValue(Turnon_VOUT_SMALL, 1);
-    }
-    else{
-        // default using 15K resister
-        PIN15_setOutputValue(Turnon_VOUT_SMALL, 1);
-    }
-    volt_rec_en = false;
+    // if(VOUTLevel == 0){
+    //     // VOUT gain level = 0, using 240K resister
+    //     PIN_setOutputValue(pin_handle, Turon_VOUT_SMALL, 0);
+    // }
+    // else if(VOUTLevel == 1){
+    //     // VOUT gain level = 1, using 15K resister
+    //     PIN_setOutputValue(pin_handle, Turon_VOUT_SMALL, 1);
+    // }
+    // else if(VOUTLevel == 2){
+    //     // VOUT gain level = 2, using 15K resister
+    //     PIN_setOutputValue(pin_handle, Turon_VOUT_SMALL, 1);
+    // }
+    // else{
+    //     // default using 15K resister
+    //     PIN_setOutputValue(pin_handle, Turon_VOUT_SMALL, 1);
+    // }
+    // record_flag = false;
 }
 
-#endif
+static uint32_t CalcPeriod(uint32_t freq){ //One Second = 10000
 
-static int32_t User2Real(uint16_t UserCode){
-    /* transfer usercode to real voltage value (mV) */
-    return (int32_t)((UserCode - 25000) / 5);
+    uint32_t period;
+
+    if (freq == 1) {
+        period = 666667;
+    } else {
+        period = (1000000 + freq / 2) / freq; // [sec]
+    }
+
+    if (period < 20){
+        period = 20;
+    }
+
+    return period;
 }
 
+static uint32_t CalcDelayTime(uint32_t freq){  //freq[10mHz]
+    uint32_t delayTime, decadeSamplingTime;
+    delayTime = CalcPeriod(freq) * instru.delay;    //get delay time
+    if (delayTime < 20) {
+        delayTime = 20;
+    } else {
+        delayTime = (delayTime + 5) / 10;
+    }
+
+    // 10kHz
+    if (freq >= 1000000) {
+        decadeSamplingTime = 1025;
+    }
+
+    // 1kHz
+    else if (freq >= 100000) {
+        decadeSamplingTime = 1025;
+    }
+
+    // 100Hz
+    else if (freq >= 10000) {
+        decadeSamplingTime = 1025;
+    }
+
+    // 10Hz
+    else if (freq >= 1000) {
+        decadeSamplingTime = 11395;
+    }
+
+    // 1Hz
+    else if (freq >= 100) {
+        decadeSamplingTime = 56900;
+    }
+
+    //0.1Hz
+    else if (freq >= 10) {
+        decadeSamplingTime = 546000;
+    }
+
+    // 0.015Hz | 136s
+    else if (freq >= 1) {
+        decadeSamplingTime = 1364995;
+    }
+
+    delayTime += decadeSamplingTime; //delay+reading time
+
+    return delayTime;
+}
+
+static uint32_t User2Freq(uint32_t UserCode){
+    uint32_t freq;
+    freq = UserCode * 15 / 10;
+    return freq; //[10mHz]
+}
+
+static uint32_t Freq2DAC(uint32_t freq){
+    uint32_t code;
+    code = freq * 10 / 15;
+    return code; //return code
+}
 
 // DAC Vout theoretical boundary <300, 100~ (mV)
 #define DAC_VOUT_GAIN_SMALL_BOUNDARY           100000  // 25500(usercode) = 100 mV
@@ -70,25 +213,47 @@ static void AutoGainChangeVout(int32_t userCode){
     // switch to 1 level volt(small)   15K
     // switch to 2 level volt(large)   240K
 
-    if(instru.VoutGainLv == VOUT_GAIN_AUTO){
-        instru.VoutGainLv = VOUT_GAIN_15K;
-        VoutGainControl(instru.VoutGainLv);
+    if(instru.VoutGainLevel == VOUT_GAIN_AUTO){
+        instru.VoutGainLevel = VOUT_GAIN_15K;
+        VoutGainControl(instru.VoutGainLevel);
     }
 
-    if(instru.VoutGainLv == VOUT_GAIN_15K){
+    if(instru.VoutGainLevel == VOUT_GAIN_15K){
         if(RealVolt > DAC_VOUT_GAIN_LARGE_BOUNDARY || RealVolt < -1 * DAC_VOUT_GAIN_LARGE_BOUNDARY){
             // switch to 2 level volt(large)
-            instru.VoutGainLv = VOUT_GAIN_240K;
-            VoutGainControl(instru.VoutGainLv);
+            instru.VoutGainLevel = VOUT_GAIN_240K;
+            VoutGainControl(instru.VoutGainLevel);
         }
     }
-    else if(instru.VoutGainLv == VOUT_GAIN_240K){
+    else if(instru.VoutGainLevel == VOUT_GAIN_240K){
         if(RealVolt < DAC_VOUT_GAIN_SMALL_BOUNDARY && RealVolt > -1 * DAC_VOUT_GAIN_SMALL_BOUNDARY ){
             // switch to 1 level volt(small)
-            instru.VoutGainLv = VOUT_GAIN_15K;
-            VoutGainControl(instru.VoutGainLv);
+            instru.VoutGainLevel = VOUT_GAIN_15K;
+            VoutGainControl(instru.VoutGainLevel);
         }
     }
 }
 
+static void cali_SetWGAmp(uint32_t ampcode){
+    AD5940_SPIWriteReg(WGCON, 0x0); // 0x0: DC disable ac first
+    AD5940_SPIWriteReg(WGAMPLITUDE, ampcode);
+    AD5940_SPIWriteReg(WGCON, 0x00000004); //0x4: Sinusoid
+}
+
+static void SetWGAmp(uint16_t ampcode, uint32_t freq){
+    uint32_t amplitude = 0;
+    amplitude = Cali_HSAMP(ampcode, freq);
+
+    cali_SetWGAmp(amplitude);
+}
+
+static void SetEISHIGHZ(uint8_t ret){
+    uint32_t code;
+
+    // select_REG_RRR(LPTIASW0); //LPTIASW0
+    code = AD5940_SPIReadReg(LPTIASW0);
+    code = (code & (~(1 << 2))) | (ret << 2); //ret = 0 HighZ on | ret = 1 HighZ off
+    AD5940_SPIWriteReg(LPTIASW0, code);
+}
+
 #endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteFlagCTInit.h

@@ -1,32 +0,0 @@
-
-#ifndef ELITE_FLAG_CT_INIT
-#define ELITE_FLAG_CT_INIT
-
-// GPT counter
-struct _GPT{
-    uint32_t GptimerCounter;
-    uint32_t GptimerCounter0;
-    uint8_t  DeltaGptimerCounter;
-    uint32_t SampleRateCounter;
-    uint32_t NotifyCounter;
-    uint32_t VscanRateCounter;
-    uint32_t LeadTimeCounter;
-    uint32_t BatteryADCCounter;
-    uint32_t BatteryCheckCounter;
-    uint32_t GptimerMultiple;
-    uint32_t StiCounter;
-}GPT = {0};
-
-static void InitGPT(){
-    GPT.GptimerCounter      = 0;
-    GPT.GptimerCounter0     = 0;
-    GPT.DeltaGptimerCounter = 0;
-    GPT.SampleRateCounter   = 0;
-    GPT.NotifyCounter       = 0;
-    GPT.VscanRateCounter    = 0;
-    GPT.LeadTimeCounter     = 0;
-    GPT.BatteryADCCounter   = 0;
-    GPT.BatteryCheckCounter = 0;
-    GPT.StiCounter          = 0;
-}
-#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteGPTimer.h

@@ -1,38 +0,0 @@
-/* Copyright (c) 2019. BioPro. Scientific.
- */
-#ifndef HEADSTAGE_GPTIMER_H
-#define HEADSTAGE_GPTIMER_H
-
-#include <Board.h>
-#include <ti/drivers/timer/GPTimerCC26XX.h>
-#include <ti/sysbios/BIOS.h>
-#include <xdc/runtime/Types.h>
-
-#define EVT_PERIODIC_GPTIMER EVT_PERIODIC_0
-
-static GPTimerCC26XX_Handle gptimer_handle;
-
-static void elite_gptimer_callback(GPTimerCC26XX_Handle handle, GPTimerCC26XX_IntMask interruptMask);
-
-#define elite_gptimer_start() GPTimerCC26XX_start(gptimer_handle)
-#define elite_gptimer_stop() GPTimerCC26XX_stop(gptimer_handle)
-#define elite_gptimer_close() GPTimerCC26XX_close(gptimer_handle)
-#define CLOCK_FREQ 4769  // clock freq = 0.1 ms(4800), Measured(4769)
-
-#define elite_gptimer_open()                                                                          \
-    do {                                                                                              \
-        GPTimerCC26XX_Params params;                                                                  \
-        GPTimerCC26XX_Params_init(&params);                                                           \
-        params.width          = GPT_CONFIG_16BIT;                                                     \
-        params.mode           = GPT_MODE_PERIODIC_UP;                                               \
-        params.debugStallMode = GPTimerCC26XX_DEBUG_STALL_OFF;                                        \
-        gptimer_handle        = GPTimerCC26XX_open(Board_GPTIMER0A, &params);                         \
-        Types_FreqHz  freq;                                                                           \
-        BIOS_getCpuFreq(&freq);                                                                       \
-        GPTimerCC26XX_Value loadVal = freq.lo / 1000 - 1; /*47999*/                                   \
-        GPTimerCC26XX_setLoadValue(gptimer_handle, loadVal);                                          \
-        GPTimerCC26XX_setLoadValue(gptimer_handle, CLOCK_FREQ); /* 0.1 ms*/                           \
-        GPTimerCC26XX_registerInterrupt(gptimer_handle, elite_gptimer_callback, GPT_INT_TIMEOUT);     \
-    } while (0)
-
-#endif  // HEADSTAGE_GPTIMER_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteI2C.h

@@ -1,95 +0,0 @@
-
-#ifndef ELITE_I2C
-#define ELITE_I2C
-
-/*
-* Read I2C example in
-* http://software-dl.ti.com/dsps/dsps_public_sw/sdo_sb/targetcontent/tirtos/2_14_02_22/
-*        exports/tirtos_full_2_14_02_22/docs/doxygen/html/_i2_c_c_c26_x_x_8h.html
-*
-*/
-
-#include <ti/drivers/I2C.h>
-#include <ti/drivers/Power.h>
-#include <stdint.h>
-#include <stdbool.h>
-#include <stddef.h>
-
-// I2C
-static I2C_Handle I2Chandle;
-static I2C_Params I2Cparams;
-static I2C_Transaction i2cTrans;
-
-#define I2CBufSize 4
-static uint8_t I2CtxBuf[I2CBufSize];      // Transmit buffer
-static uint8_t I2CrxBuf[I2CBufSize];      // Receive buffer
-bool transferDone = false;
-
-static void I2CCallbackFunction(I2C_Handle handle, I2C_Transaction *msg, bool transfer) {
-    if(transfer){
-        transferDone = true;
-    }
-}
-
-static void I2Cinit(){
-    I2C_init();
-
-    // Configure I2C parameters.
-    I2C_Params_init(&I2Cparams);
-
-    I2Cparams.transferMode  = I2C_MODE_CALLBACK;
-    I2Cparams.transferCallbackFxn = I2CCallbackFunction;
-    I2Cparams.bitRate  = I2C_100kHz;
-
-    // Initialize master I2C transaction structure
-    i2cTrans.writeCount   = I2CBufSize;
-    i2cTrans.writeBuf     = I2CtxBuf;
-    i2cTrans.readCount    = I2CBufSize;
-    i2cTrans.readBuf      = I2CrxBuf;
-    i2cTrans.slaveAddress = 0xA0;
-
-    for(int i=0 ; i<10 ; i++){
-        I2CtxBuf[i] = 0;
-        I2CrxBuf[i] = 0;
-    }
-
-    // Open I2C
-    I2Chandle = I2C_open(Board_I2C, &I2Cparams);
-
-}
-#define WriteMem 0b10100001
-#define ReadMem  0b10100000
-
-static void I2CWrite(uint8_t addr, uint8_t data){
-    for(int i=0 ; i<I2CBufSize ; i++){
-        I2CtxBuf[i] = 0;
-        I2CrxBuf[i] = 0;
-    }
-
-    I2CtxBuf[0] = WriteMem;
-    I2CtxBuf[1] = addr;
-    I2CtxBuf[2] = data;
-
-//    I2Chandle = I2C_open(Board_I2C, &I2Cparams);
-    I2C_transfer(I2Chandle, &i2cTrans);
-//    I2C_close(I2Chandle);
-}
-
-
-static void I2CRead(uint8_t addr){
-    for(int i=0 ; i<I2CBufSize ; i++){
-        I2CtxBuf[i] = 0;
-        I2CrxBuf[i] = 0;
-    }
-
-    I2CtxBuf[0] = ReadMem;
-    I2CtxBuf[1] = addr;
-
-//    I2Chandle = I2C_open(Board_I2C, &I2Cparams);
-    I2C_transfer(I2Chandle, &i2cTrans);
-//    I2C_close(I2Chandle);
-}
-
-
-#endif  // ELITE_I2C
-

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteInstruction.h

@@ -1,8 +1,5 @@
-/*=============================================================================
- =                          instr.h                                              =
- =============================================================================*/
-#ifndef ELITE_INSTR_H
-#define ELITE_INSTR_H
+#ifndef __INSTR_H__
+#define __INSTR_H__
 
 #ifdef __cpulsplus
 extern "C" {
@@ -15,13 +12,9 @@ struct HEADSTAGE_INSTRUCTION {
     uint8_t  chip_id;
     uint8_t  eliteFxn;
 
-    // time relation
+    /** DAC parameter **/
     uint8_t  VsetRateIndex;
     uint32_t VsetRate;
-    uint32_t sampleRate;
-    uint32_t notifyRate;
-    uint32_t period;
-
     int32_t  Vset;
     uint16_t VoltConstant;
     uint8_t  directionInit;
@@ -32,40 +25,46 @@ struct HEADSTAGE_INSTRUCTION {
     int32_t  Vmax;
     int32_t  Vmin;
 
-    uint32_t steptime;
+    /** EIS **/
+    uint32_t f1;
+    uint32_t f2;
+    uint32_t fmax;
+    uint32_t fmin;
+    uint32_t fset;
+    uint16_t dcbias;
+    uint16_t delay;
+    uint16_t acamp;
+    uint8_t  avgnum;
+    uint8_t  rtia;
+    uint16_t ppd;
+    uint8_t  scale;
+    int32_t  real;
+    int32_t  imag;
+    uint8_t  periodIndex;
+    uint32_t delayTime;
+    uint8_t  settingIndex;
 
-    uint8_t  IinADCAutoGainEn;
-    uint8_t  VinADCAutoGainEn;
-    uint8_t  VoutAutoGainEn;
-    uint8_t  IinADCGainLv;
+
+    /** ADC parameter **/
+    uint8_t  notifyRateIndex;
+    uint32_t sampleRate;
+    uint8_t  VoViSwitch;
+    uint8_t  VinAutoGainEnable;
+    uint8_t  VoutAutoGainEnable;
+    uint8_t  ADCGainLv;
+
+     // voltage output gain
+    uint16_t VoutGainLevel;
     uint8_t  VinADCGainLv;
-    uint16_t VoutGainLv;
-    uint8_t  gain_switch_on;
-    uint8_t  AdcChannel;
-    bool     hign_z_en;
 
+    /** Notify parameter **/
+    uint32_t notifyRate;
+
+    /** mode parameter **/
     uint16_t cycleNumber;
     uint8_t  charge;
     int32_t  constantCurrent;
-
-    // uni pulse mode
-    int32_t  v0;
-    uint32_t t_pulse[4];
-    int32_t  v_initial[4];
-    int32_t  v_slope[4];
-    int32_t  v_step[4];
-    uint32_t t_pulse_min[4];
-    uint32_t t_pulse_max[4];
-    int32_t  v_stop;
-    int32_t  v_up;
-    int32_t  v_low;
-    bool     v_invert_option;
-    bool     v_stop_direction;
-    int32_t  v_1;
-    int32_t  v_2;
-
-
-    // pulse mode
+    int32_t  Currentmax;
     int32_t  sti_v1;
     int32_t  sti_v2;
     int32_t  sti_v3;
@@ -83,51 +82,118 @@ struct HEADSTAGE_INSTRUCTION {
     uint16_t sti_cy;
     uint16_t sti_loop;
 
-    int32_t Vout;
-
-    // not use
-    int32_t  Currentmax;
-    uint8_t  VoViSwitch;
-
+    uint16_t StepTime;
 
+    uint8_t AdcChannel;
 
+    /* EIS DAC parameter */
+    uint8_t DAC_type;
+    uint16_t VAmpSet;          // DAC Voltage Amplitude
 
+    /* EIS ADC parameter */
+    uint8_t  gain_lv_hstia;
+    uint8_t  HSTIAAutoGainEnable;
+    uint8_t  gain_lv_lptia;
+    uint8_t  LPTIAAutoGainEnable;
 
+    //VT mode
+    uint8_t measure_vin_range;
 } instru = {0};
 
-/** Iin, Vin, Vout **/
-#define RIS_ADC_IIN         0x00
-#define RIS_ADC_VIN         0x01
-#define RIS_DAC_VOUT        0x02
-#define RIS_HIGH_Z          0x03
-#define RIS_ADC_VOUT        0x04
-#define RIS_ADC_BAT         0x05
+/** ADC Iin gain level **/
+#define I_GAIN_3M           0x07    // largest gain
+#define I_GAIN_100K         0x08
+#define I_GAIN_3K           0x09
+#define I_GAIN_100R         0x0A    // the least gain
+#define I_GAIN_AUTO         0x04
 
-// ADC Iin gain level !!! move to ADC.h in future
-#define I_GAIN_3M       0x00    // lv0,largest gain
-#define I_GAIN_100K     0x01    // lv1
-#define I_GAIN_3K       0x02    // lv2
-#define I_GAIN_100R     0x03    // lv3,the least gain
-#define I_GAIN_AUTO     0x04
+// EIS LPTIA Iin Gain Level //
+//#define LPRTIA_512K         0x00
+#define LPRTIA_64K          0x00
+#define LPRTIA_8K           0x01
+#define LPRTIA_1K           0x02
+#define LPRTIA_200R         0x03
+#define LPRTIA_GAIN_AUTO    0x04
+#define DISCONNECT_RTIA     0x05
 
-// ADC Vin gain level !!! move to ADC.h in future
-#define VIN_GAIN_1M     0x00
-#define VIN_GAIN_30K    0x01
-#define VIN_GAIN_1K     0x02
-#define VIN_GAIN_AUTO   0x03
+// EIS HSTIA Iin Gain Level
+enum hsrtia_gain_e {
+    HSRTIA_160K = 0,
+    HSRTIA_80K,
+    HSRTIA_40K,
+    HSRTIA_20K,
+    HSRTIA_10K,
+    HSRTIA_5K,
+    HSRTIA_1K,
+    HSRTIA_200R,
+    
+    HSRTIA_MAX,
+};
 
-// DAC Vout gain level !!! move to DAC.h in future
-#define VOUT_GAIN_240K  0x00
-#define VOUT_GAIN_15K   0x01
-#define VOUT_GAIN_AUTO  0x02
+/** ADC Vin gain level **/
+#define VIN_GAIN_1M         0x00
+#define VIN_GAIN_30K        0x01
+#define VIN_GAIN_1K         0x02
+#define VIN_GAIN_AUTO       0x03
+
+/** Vout gain level **/
+#define VOUT_GAIN_240K      0x00
+#define VOUT_GAIN_15K       0x01
+#define VOUT_GAIN_AUTO      0x02
 
 /* DAC reset parameter */
-#define DAC_ZERO    25000 // DAC_ZERO is about 0V
+#define DAC_ZERO            25000
+#define EIS_HSDAC_ZERO      0x0800
 
 // Step time macro
-#define STEPTIME_HALF_SEC 5000
-#define STEPTIME_ONE_SEC 10000
-#define STEPTIME_TWO_SEC 20000
+#define STEPTIME_HALF_SEC   5000
+#define STEPTIME_ONE_SEC    10000
+#define STEPTIME_TWO_SEC    20000
+
+/* AVG Number */
+#define AVG2               0
+#define AVG4               1
+#define AVG8               2
+#define AVG16              3
+
+#define ADC1M6sps          0
+#define ADC800Ksps         1
+
+#define Sinc3OSR5          0
+#define Sinc3OSR4          1
+#define Sinc3OSR2          2
+
+#define Sinc2OSR22         0
+#define Sinc2OSR44         1
+#define Sinc2OSR89         2
+#define Sinc2OSR178        3
+#define Sinc2OSR267        4
+#define Sinc2OSR533        5
+#define Sinc2OSR640        6
+#define Sinc2OSR667        7
+#define Sinc2OSR800        8
+#define Sinc2OSR889        9
+#define Sinc2OSR1067      10
+#define Sinc2OSR1333      11
+
+#define DFTNUM4            0
+#define DFTNUM8            1
+#define DFTNUM16           2
+#define DFTNUM32           3
+#define DFTNUM64           4
+#define DFTNUM128          5
+#define DFTNUM256          6
+#define DFTNUM512          7
+#define DFTNUM1024         8
+#define DFTNUM2048         9
+#define DFTNUM4096        10
+#define DFTNUM8192        11
+#define DFTNUM16384       12
+
+#define AD5940_SYS_CLOCK    16000000
+#define Cutoff_Freq         37000000  // 210kHz
+
+static uint32_t HSRTIATable[4] = {160000, 20000, 5000, 200};
 
 /*********************************************************************
  * @fn      InitEliteInstruction
@@ -138,72 +204,51 @@ struct HEADSTAGE_INSTRUCTION {
  *
  * @return  None.
  */
-static void InitEliteInstruction(void)
-{
-    instru.chip_id         = 0;
-    instru.eliteFxn        = 0;         //default is a null event
+static void InitEliteInstruction(){
+    instru.chip_id              = 0;
+    instru.eliteFxn             = 0;         //default is a null event
+    instru.VsetRateIndex        = 0;
+    instru.VsetRate             = 2;
+    instru.Vset                 = 0;
+    instru.VoltConstant         = DAC_ZERO; //DAC_ZERO is about 0V
+    instru.directionInit        = 1;        //0:reverse        1:forward
+    instru.step                 = 0;
+    instru.Ve1                  = DAC_ZERO;
+    instru.Ve2                  = DAC_ZERO;
+    instru.Vinit                = 0;
+    instru.Vmax                 = 0;
+    instru.Vmin                 = 0;
+    instru.notifyRateIndex      = 100;
+    instru.sampleRate           = 15;
+    instru.VoViSwitch           = 0x01;    //0:user see Vo     1: user see Vi
+    instru.VinAutoGainEnable    = 1;
+    instru.VoutAutoGainEnable   = 1;
+    instru.VoutGainLevel        = VOUT_GAIN_AUTO;
+    instru.VinADCGainLv         = VIN_GAIN_AUTO;
+    instru.notifyRate           = STEPTIME_ONE_SEC;
+    instru.cycleNumber          = 1;
+    instru.charge               = 1;      //0:discharge        1:charge
+    instru.constantCurrent      = 0;
+    instru.Currentmax           = 0;
+    instru.StepTime             = STEPTIME_ONE_SEC;
+    instru.AdcChannel           = 0;
 
-    instru.VsetRateIndex   = 0;         // vscan rate
-    instru.VsetRate        = 2;
-    instru.sampleRate      = 20;        // ADC's sample rate
-    instru.notifyRate      = CLOCK_ONE_SECOND;   // send data's rate
-    instru.period          = CLOCK_ONE_SECOND;
+    //EIS
+    instru.f1                   = 0;
+    instru.f2                   = 0;
+    instru.fset                 = 0;
+    instru.fmax                 = 0;
+    instru.fmin                 = 0;
+    instru.delay                = 0;
+    instru.scale                = 0;
+    instru.avgnum               = 0;
+    instru.dcbias               = 0;
+    instru.acamp                = 0;
+    instru.ppd                  = 1;
+    instru.periodIndex          = 0;
+    instru.delayTime            = 0;
+    instru.settingIndex         = 0;
 
-    instru.Vset            = 0;         // vscan's volt[5nv]
-    instru.VoltConstant    = DAC_ZERO;  // DAC's volt[UC]
-    instru.directionInit   = 1;         // 0:reverse, 1:forward
-    instru.step            = 0;
-    instru.Ve1             = DAC_ZERO;  // user set volt[UC]
-    instru.Ve2             = DAC_ZERO;  // user set volt[UC]
-    instru.Vinit           = 0;         // user set init volt[5nv]
-    instru.Vmax            = 0;         // user set max volt[5nv]
-    instru.Vmin            = 0;         // user set min voit[5nv]
-
-    instru.IinADCAutoGainEn = 1;
-    instru.VinADCAutoGainEn = 1;
-    instru.VoutAutoGainEn   = 1;
-    instru.IinADCGainLv     = I_GAIN_AUTO;
-    instru.VinADCGainLv     = VIN_GAIN_AUTO;
-    instru.VoutGainLv       = VOUT_GAIN_AUTO;
-    instru.gain_switch_on   = 0b11110000;   // cur auto gain switch, |lv0|lv1|lv2|lv3|none|none|none|none|
-    instru.AdcChannel       = 0;         // RIS_ADC_IIN: 0x00, RIS_ADC_VIN: 0x01, RIS_DAC_VOUT: 0x02, RIS_HIGH_Z: 0x03
-    instru.hign_z_en        = 1;
-
-    instru.cycleNumber     = 1;
-    instru.charge          = 1;         // 0:discharge, 1:charge
-    instru.constantCurrent = 0;
-
-    // uni pulse mode
-    instru.v0              = DAC_ZERO;  // t < 0, volt is 0v
-    instru.v_stop          = 0;
-    instru.t_pulse[0]      = 0;
-    instru.t_pulse[1]      = 0;
-    instru.t_pulse[2]      = 0;
-    instru.t_pulse[3]      = 0;
-    instru.v_initial[0]    = 0;
-    instru.v_initial[1]    = 0;
-    instru.v_initial[2]    = 0;
-    instru.v_initial[3]    = 0;
-    instru.v_slope[0]      = 0;
-    instru.v_slope[1]      = 0;
-    instru.v_slope[2]      = 0;
-    instru.v_slope[3]      = 0;
-    instru.v_step[0]       = 0;
-    instru.v_step[1]       = 0;
-    instru.v_step[2]       = 0;
-    instru.v_step[3]       = 0;
-    instru.t_pulse_min[0]  = 0;
-    instru.t_pulse_min[1]  = 0;
-    instru.t_pulse_min[2]  = 0;
-    instru.t_pulse_min[3]  = 0;
-    instru.t_pulse_max[0]  = 0;
-    instru.t_pulse_max[1]  = 0;
-    instru.t_pulse_max[2]  = 0;
-    instru.t_pulse_max[3]  = 0;
-    instru.v_invert_option = false;
-    instru.v_stop_direction = true;
-    instru.v_1              = 0;
-    instru.v_2              = 0;
 
     //pulse mode
     instru.sti_t1          = 0;
@@ -223,13 +268,19 @@ static void InitEliteInstruction(void)
     instru.sti_loop        = 1;
     instru.sti_cy          = 0;
 
-    instru.Vout            = 0;
+    //General
+    // EIS DAC
+    instru.VAmpSet              = EIS_HSDAC_ZERO;
+    instru.DAC_type             = 0;
 
-    // not use
-    instru.Currentmax      = 0;
-    instru.VoViSwitch      = 0x01;
+    // EIS ADC
+    instru.gain_lv_hstia          = HSRTIA_200R;
+    instru.HSTIAAutoGainEnable    = 1;
+    instru.gain_lv_lptia          = LPRTIA_200R;
+    instru.LPTIAAutoGainEnable    = 1;
 
-    return;
+    // VT mode
+    instru.measure_vin_range = 0;
 }
 
 #ifdef __cpulsplus

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteKeyDetect.h

@@ -1,74 +0,0 @@
-
-#ifndef ELITEKEYDETECT
-#define ELITEKEYDETECT
-
-static bool TurnOnElite(uint8_t key) {
-    static uint16_t TurnOnCounter = 0;
-
-    if (key == 0) {
-        // press 1 sec, power on LED, read bat power
-        if (TurnOnCounter >= CLOCK_ONE_SECOND) {
-            headstage_battery_volt();
-            uint16_t bat = NotifyVoltBat;
-            if( bat < 768 && bat > 20){
-                PIN15_setOutputValue(enable_5v, 0);
-                return false;
-            }else{
-                PIN15_setOutputValue(enable_5v, 1);  // enable 5V
-                TurnOn10V();
-                ModeLED(BT_WAIT);
-                return true;
-            }
-        } else {
-            TurnOnCounter++;
-            return false;
-        }
-    } else {
-        TurnOnCounter = 0;
-        PIN15_setOutputValue(enable_5v, 0);  // disable 5V
-        return false;
-    }
-}
-
-static void EliteKeyPress(uint8_t key) {
-    static uint16_t ShutDownCounter = 0;
-    static uint8_t OriginEliteFxn  = 0;
-
-    if (key == 0) {
-        // key = 0 if press
-        // press key => bight LED
-
-        if (ShutDownCounter == CLOCK_ONE_SECOND) {
-            KEYLED();
-        }
-
-        // press 3~4 sec, shutdown 2650
-        else if (ShutDownCounter > (CLOCK_ONE_SECOND*3) ) {
-            LED_color(DARKLED, 0xFF, 0xFF, 0x00);
-            PIN15_setOutputValue(enable_5v, 0);  // disable 5V
-        }
-        ShutDownCounter ++;
-    } else {
-        if (OriginEliteFxn == instru.eliteFxn) {  // old function == currunt instruction
-            if (ShutDownCounter != 0) {
-                // dark LED
-                checkFlafLED();
-                ShutDownCounter = 0;
-            }
-        } else {  // old function != currunt instruction
-            OriginEliteFxn = instru.eliteFxn;
-            if (ShutDownCounter != 0) {
-                ShutDownCounter = 0;
-            }
-            checkFlafLED();
-        }
-    }
-}
-
-static void TurnOn10V() {
-    If10Von = true;
-    PIN15_setOutputValue(enable_10v, 1);
-    CPUdelay(8000);
-}
-
-#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteLED.h

@@ -2,9 +2,6 @@
 #ifndef ELITELED
 #define ELITELED
 
-#define DARKLED                  0xE1
-#define LIGHTLED                 0xE8
-
 static bool     btWaitLedFlag   = 0;
 static bool     noEventLedFlag  = 0;
 static bool     preWorkLedFlag  = 0;
@@ -13,93 +10,6 @@ static bool     postWorkLedFlag = 0;
 
 static void WorkModeLED();
 
-static void LED_color(uint8_t bright, uint8_t red, uint8_t green, uint8_t blue) {
-    spi_LEDtxbuf[0] = 0x0000;
-    spi_LEDtxbuf[1] = 0x0000;
-    for (int i = 2; i < SPI_LED_SIZE - 2; i += 2) {
-        spi_LEDtxbuf[i]     = 0xE000 | ((uint16_t)bright << 8) | blue;
-        spi_LEDtxbuf[i + 1] = ((uint16_t)green << 8) | red;
-    }
-
-    spi_LEDtxbuf[SPI_LED_SIZE - 2] = 0xffff;
-    spi_LEDtxbuf[SPI_LED_SIZE - 1] = 0xffff;
-
-    LED_SPI(SPI_LED_SIZE, spi_LEDtxbuf, spi_LEDrxbuf);
-}
-
-static void Elite_led_color(uint16_t color){
-    switch (color) {
-        case COLOR_RED: {
-            LED_color(DARKLED, 0xFF, 0x00, 0x00);
-            break;
-        }
-        case COLOR_ORANGE: {
-            LED_color(DARKLED, 0xFF, 0x58, 0x09);
-            break;
-        }
-        case COLOR_YELLOW: {
-            LED_color(LIGHTLED, 0xFF, 0x80, 0x00);
-            break;
-        }
-        case COLOR_GREEN: {
-            LED_color(DARKLED, 0x00, 0xFA, 0x00);
-            break;
-        }
-        case COLOR_YELLOWGREEN: {
-            LED_color(DARKLED, 0x64, 0xA6, 0x00);
-            break;
-        }
-        case COLOR_BLUE: {
-            LED_color(DARKLED, 0x00, 0x00, 0xAA);
-            break;
-        }
-        case COLOR_CYAN: {
-            LED_color(DARKLED, 0x00, 0x40, 0x40);
-            break;
-        }
-        case COLOR_MAGENTA: {
-            LED_color(DARKLED, 0xFF, 0x00, 0x80);
-            break;
-        }
-        case COLOR_PURPLE: {
-            LED_color(DARKLED, 0xFF, 0x00, 0xFF);
-            break;
-        }
-        case COLOR_WHITE: {
-            LED_color(DARKLED, 0xCA, 0xFF, 0xFF);
-            break;
-        }
-        case COLOR_BLACK: {
-            LED_color(0x00, 0x00, 0x00, 0x00);
-            break;
-        }
-        //dark LED
-        case COLOR_YELLOW_DARK: {
-            LED_color(DARKLED, 0xFF, 0x80, 0x00);
-            break;
-        }
-        case COLOR_GREEN_DARK: {
-            LED_color(DARKLED, 0x00, 0x33, 0x00);
-            break;
-        }
-        case COLOR_BLUE_DARK: {
-            LED_color(DARKLED, 0x00, 0x00, 0x33);
-            break;
-        }
-        case COLOR_CYAN_DARK: {
-            LED_color(DARKLED, 0x00, 0x10, 0x10);
-            break;
-        }
-        case COLOR_PURPLE_DARK: {
-            LED_color(DARKLED, 0x55, 0x00, 0x55);
-            break;
-        }
-        default: {
-            break;
-        }
-    }
-}
-
 static void ModeLED(uint16_t modeStatus) {
     btWaitLedFlag   = 0;
     noEventLedFlag  = 0;
@@ -108,53 +18,47 @@ static void ModeLED(uint16_t modeStatus) {
     postWorkLedFlag = 0;
 
     switch (modeStatus) {
-    case BT_WAIT: {
-        btWaitLedFlag = 1;
-        BT_WAIT_LED();
-        break;
-    }
-    case NO_EVENT: {
-        noEventLedFlag = 1;
-        LEDPowerON();
-        break;
-    }
-    case PRE_WORK: {
-        preWorkLedFlag = 1;
-        Elite_led_color(COLOR_BLUE);
-        break;
-    }
-    case WORKING: {
-        workingLedFlag = 1;
-        WorkModeLED();
-        break;
-    }
-    case POST_WORK: {
-        postWorkLedFlag = 1;
-        Elite_led_color(COLOR_BLUE);
-        break;
-    }
-    default: {
-        LEDPowerON();
-        break;
-    }
+        case BT_WAIT:
+            btWaitLedFlag = 1;
+            led_color_set(LED_NB_MAX, LED_BR_LV1, LED_CLR_YELLOWGREEN);
+            break;
+
+        case NO_EVENT:
+            noEventLedFlag = 1;
+            led_color_set(LED_NB_MAX, LED_BR_LV1, LED_CLR_GREEN);
+            break;
+
+        case PRE_WORK:
+            preWorkLedFlag = 1;
+            led_color_set(LED_NB_MAX, LED_BR_LV1, LED_CLR_BLUE);
+            break;
+
+        case WORKING:
+            workingLedFlag = 1;
+            WorkModeLED();
+            break;
+
+        case POST_WORK:
+            postWorkLedFlag = 1;
+            led_color_set(LED_NB_MAX, LED_BR_LV1, LED_CLR_BLUE);
+            break;
+
+        default:
+            break;
     }
 }
 
 static void checkFlafLED()
 {
-    if(btWaitLedFlag == 1){
+    if(btWaitLedFlag == 1) {
         ModeLED(BT_WAIT);
-    }
-    else if(noEventLedFlag == 1){
+    } else if(noEventLedFlag == 1) {
         ModeLED(NO_EVENT);
-    }
-    else if(preWorkLedFlag == 1){
+    } else if(preWorkLedFlag == 1) {
         ModeLED(PRE_WORK);
-    }
-    else if(workingLedFlag == 1){
+    } else if(workingLedFlag == 1) {
         ModeLED(WORKING);
-    }
-    else if(postWorkLedFlag == 1){
+    } else if(postWorkLedFlag == 1) {
         ModeLED(POST_WORK);
     }
 }
@@ -162,34 +66,13 @@ static void checkFlafLED()
 static void WorkModeLED()
 {
     switch (instru.eliteFxn) {
-        case CURVE_IV:
-        case CURVE_VO:
-        case CURVE_RT:
-        case CURVE_VT:
-        case CURVE_IT:
+        case CURVE_EIS:
         case CURVE_CV:
         case CURVE_CA:
-        case CURVE_CC:
-        case CURVE_OCP:
-        case CURVE_LSV:
-        case CURVE_IV_CY:
-        case CURVE_PULSE:
-        case CURVE_UNI_PULSE:
-        case CURVE_DPV:
-        case CURVE_DPV_SMPRATE:
-        case CURVE_DPV_ADVANCE:
-        case CURVE_DPV_ADVANCE_SMPRATE:
-            WORKLED();
-            break;
-
-        case CURVE_CALI_ADC:
-            if (instru.AdcChannel == RIS_ADC_IIN) {
-                Elite_led_color(COLOR_RED);
-            } else if (instru.AdcChannel == RIS_ADC_VIN) {
-                Elite_led_color(COLOR_ORANGE);
-            } else if (instru.AdcChannel == RIS_DAC_VOUT) {
-                Elite_led_color(COLOR_BLUE);
-            }
+        case CURVE_VT:
+        case CURVE_RT:
+        case CURVE_CF:
+            led_color_set(LED_NB_MAX, LED_BR_LV1, LED_CLR_CYAN);
             break;
 
         default:

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteLatchInit.h

@@ -1,16 +0,0 @@
-
-#ifndef ELITE_LATCH_INIT
-#define ELITE_LATCH_INIT
-
-static void InitLH() {
-    for (int i=0; i<LATCH_BUFF_SIZE; i++) {
-        LH.LATCH0[i]       = 0;
-        LH.LATCH1[i]       = 0;
-        LH.LATCH2[i]       = 0;
-    }
-    LH.LoadState    = 0;
-}
-
-
-#endif
-

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteNotify.h

@@ -8,25 +8,59 @@
 #define ELITENOTIFY
 
 #include "headstage.h"
-#include <string.h>
 
 /*notify's input type*/
-#define NOTIFY_CURRENT      0
-#define NOTIFY_VOLT         1
-#define NOTIFY_IMPEDANCE    2
-#define NOTIFY_VOLT_BAT     3
-#define NOTIFY_TEMPERATURE  4
+#define NOTIFY_CURRENT   0
+#define NOTIFY_VOLT      1
+#define NOTIFY_IMPEDANCE 2
+#define NOTIFY_VOLT_BAT  3
 
-#define FINISH_MODE_INS 0b10100000
 
 static uint32_t not_time_stamp;
-static uint8_t  NotifyCurrent[4]   = {0};
-static uint8_t  NotifyVolt[4]      = {0};
-static uint8_t  NotifyImpedance[4] = {0};
-static uint16_t NotifyVoltBat      = 0;
-static uint16_t NotifyTemperature  = 0;
+
+static uint8_t  NotifyCh1[4] = {0};
+static uint8_t  NotifyCh2[4] = {0};
+static uint8_t  NotifyCh3[4] = {0};
+static uint8_t  NotifyVoltBat[4]   = {0};
 static uint16_t NotifyCycleNumber  = 0;
-static bool  finishMode         = false;
+static uint8_t  finishMode         = 0;
+static uint8_t  gain = 0;
+static int32_t notify_one = 0;
+static int32_t notify_two = 0;
+static int32_t notify_three = 0;
+static uint32_t NotifyCh4 = 0;
+
+// ****************** New Notify Format ******************************** //
+/*
+ * Notify format
+ *
+ *
+         |               |   1           |       2       |           3   |
+         0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2
+         -----------------------------------------------------------------
+         |    header     |
+         |    current                                                    |
+         | voltage or impedance                                          |
+         |  mode & gain  |
+         |    time stamp                                                 |
+         |  cycle number |
+
+
+    mode & gain
+        this byte include Elite working mode and ADC gain level
+        we use "(mode & 0xF0) | (gain & 0x0F)" to encode these two information
+
+     cycle number
+         for cyclic voltammetry use, we save it as channel number.
+         0xFF
+
+  * header = device ID
+  * I = current (0.001nA), V = voltage (mV),
+  * Z = impedance (k ohm), T = time (ms)
+  *
+  *
+*/
+// ********* End New Format Notify ***************************************** //
 
 /*
  * Notify format
@@ -52,67 +86,75 @@ static bool  finishMode         = false;
   *
   *
 */
-static void SendNotify() {
-    static uint8_t notify_times = 0;
-    uint32_t bat = NotifyVoltBat;
+static void initDATBuf(void)
+{
+    memset(not_buf, 0, BLE_DAT_BUFF_SIZE);
+    
+    return;
+}
 
+static void initINSBuf(void)
+{
+    memset(ins_buf, 0, BLE_INS_BUFF_SIZE);
+    
+    return;
+}
+
+static void initCISBuf(void)
+{
+    memset(cis_buf, 0, BLE_CIS_BUFF_SIZE);
+
+    return;
+}
+
+static void SendNotify() {
     initDATBuf();
 
+    not_buf[0] = instru.chip_id;
+
+    for (int i = 0; i < 4; i++) {
+        not_buf[i + 1] = NotifyCh1[i]; // 1 2 3 4
+        not_buf[i + 5] = NotifyCh2[i]; // 5 6 7 8
+        not_buf[i + 9] = NotifyCh3[i]; //9 10 11 12
+    }
+
     // 1 Timestamp = 32 usec;  31 Timestamp ~= 1 msec
     not_time_stamp = (Timestamp_get32()) / 31;  // msec
 
-    not_buf[0] = instru.chip_id;
+    not_buf[13] = not_time_stamp & 0xff;
+    not_buf[14] = (not_time_stamp >> 8) & 0xff;
+    not_buf[15] = (not_time_stamp >> 16) & 0xff;
+    not_buf[16] = (not_time_stamp >> 24) & 0xff;
 
-    memcpy(not_buf+1, (uint8_t *)&not_time_stamp, sizeof(not_time_stamp));
-    memcpy(not_buf+5, NotifyCurrent, sizeof(NotifyCurrent));
-    memcpy(not_buf+9, NotifyVolt, sizeof(NotifyVolt));
-    memcpy(not_buf+13, NotifyImpedance, sizeof(NotifyImpedance));
-    memcpy(not_buf+17, (uint8_t *)&NotifyCycleNumber, sizeof(NotifyCycleNumber));
+    not_buf[17] = (NotifyCycleNumber >> 8) & 0xff;
+    not_buf[18] = NotifyCycleNumber & 0xff;
 
-    if (finishMode) {
-        not_buf[19] = (FINISH_MODE_INS) & 0b11110000;
-    } else {
-        not_buf[19] = 0 & 0b11110000;
-    }
+    not_buf[19] = (finishMode << 7) & 0x80;
+    not_buf[20] = gain;
 
-    memcpy(not_buf+20, (uint8_t *)&bat, sizeof(bat));
-    memcpy(not_buf+24, &notify_times, sizeof(notify_times));
+    memcpy(not_buf+21, (uint8_t *)&NotifyCh4, sizeof(NotifyCh4));
+    memcpy(not_buf+25, (uint8_t *)&notify_one, sizeof(notify_one));
+    memcpy(not_buf+29, (uint8_t *)&notify_two, sizeof(notify_two));
+    memcpy(not_buf+33, (uint8_t *)&notify_three, sizeof(notify_three));
 
-    for (int i = 25; i < BLE_DAT_BUFF_SIZE; i++){
+    for (int i = 37; i < BLE_DAT_BUFF_SIZE; i++){
         not_buf[i] = 0;
     }
 
     SimpleProfile_SetParameter(BLE_DAT_BUFF_CHAR, BLE_DAT_BUFF_SIZE, not_buf);
-    notify_times++;
 }
 
-static void initDATBuf(){
-    for (int i = 0; i < BLE_DAT_BUFF_SIZE; i++){
-        not_buf[i] = 0;
-    }
-}
 
-static void initINSBuf(){
-    for (int i = 0; i < BLE_INS_BUFF_SIZE; i++){
-        ins_buf[i] = 0;
-    }
-}
-
-static void initCISBuf(){
-    for (int i = 0; i < BLE_CIS_BUFF_SIZE; i++){
-        cis_buf[i] = 0;
-    }
-}
 
 static void initRawDataBuf(){
     not_time_stamp    = 0;
     NotifyCycleNumber = 0;
-    finishMode        = false;
+    finishMode        = 0;
 
     for (int i = 0; i < 4; i++){
-        NotifyCurrent[i]   = 0;
-        NotifyVolt[i]      = 0;
-        NotifyImpedance[i] = 0;
+        NotifyCh1[i]   = 0;
+        NotifyCh2[i]      = 0;
+        NotifyCh3[i] = 0;
     }
 }
 
@@ -129,22 +171,31 @@ static void InputNotify(int NotifyType, int32_t Data){
 
     switch (NotifyType) {
         case NOTIFY_CURRENT:
-            memcpy(NotifyCurrent, (uint8_t *)&Data, sizeof(Data));
+            NotifyCh1[0] = (uint8_t)((Data & 0xFF000000) >> 24);
+            NotifyCh1[1] = (uint8_t)((Data & 0x00FF0000) >> 16);
+            NotifyCh1[2] = (uint8_t)((Data & 0x0000FF00) >> 8);
+            NotifyCh1[3] = (uint8_t)(Data & 0x000000FF);
             break;
 
         case NOTIFY_IMPEDANCE:
-            memcpy(NotifyImpedance, (uint8_t *)&Data, sizeof(Data));
+            NotifyCh3[0] = (uint8_t)((Data & 0xFF000000) >> 24);
+            NotifyCh3[1] = (uint8_t)((Data & 0x00FF0000) >> 16);
+            NotifyCh3[2] = (uint8_t)((Data & 0x0000FF00) >> 8);
+            NotifyCh3[3] = (uint8_t)(Data & 0x000000FF);
             break;
 
         case NOTIFY_VOLT :
-            memcpy(NotifyVolt, (uint8_t *)&Data, sizeof(Data));
+            NotifyCh2[0] = (uint8_t)((Data & 0xFF000000) >> 24);
+            NotifyCh2[1] = (uint8_t)((Data & 0x00FF0000) >> 16);
+            NotifyCh2[2] = (uint8_t)((Data & 0x0000FF00) >> 8);
+            NotifyCh2[3] = (uint8_t)(Data & 0x000000FF);
             break;
 
         case NOTIFY_VOLT_BAT :
-            NotifyVoltBat = (uint16_t)Data;
-            break;
-        case NOTIFY_TEMPERATURE :
-            NotifyTemperature = (uint16_t)Data;
+            NotifyVoltBat[0] = (uint8_t)((Data & 0xFF000000) >> 24);
+            NotifyVoltBat[1] = (uint8_t)((Data & 0x00FF0000) >> 16);
+            NotifyVoltBat[2] = (uint8_t)((Data & 0x0000FF00) >> 8);
+            NotifyVoltBat[3] = (uint8_t)(Data & 0x000000FF);
             break;
     }
 }

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteReset.h

@@ -3,71 +3,20 @@
 #define ELITERESET
 
 static void reset() {
+    mode_init = true;
     megaStiEnable = false;
     PeriodicEvent = false;     // is there an PeriodicEvent?
     Free_Work_Mode = true;      // Free(WorkModeData)
+    InitPeriodicEvent = true;      // need to create a WorkModeData?
 
     initINSBuf();
     initDATBuf();
 
-    PIN15_setOutputValue(HIGH_Z_MODE, 0); // HIGH Z MODE // 1: close; 0: open;
-
-    VinADCGainCtrl(VIN_GAIN_AUTO);
-    IinADCGainCtrl(I_GAIN_AUTO);
-
-    instru.VoutGainLv = VOUT_GAIN_15K;
-    VoutGainControl(instru.VoutGainLv);
-    DAC_outputV(Usercode_Correction_to_DAC(instru.VoutGainLv, 25000));
-
-    for (int i = 0; i < SPI_LED_SIZE; i++) {
-        spi_LEDtxbuf[i] = 0;
-        spi_LEDrxbuf[i] = 0;
-    }
-
-    for (int i = 0; i < SPI_DAC_SIZE; i++) {
-        spi_DACtxbuf[i] = 0;
-        spi_rxbuf[i]    = 0;
-    }
-
-    for (int i = 0; i < SPI_ADC_SIZE; i++) {
-        spi_ADC_txbuf[i] = 0;
-        spi_ADC_rxbuf[i] = 0;
-    }
+    AD5940_HWReset();
+    AD5940_Initialize();
 
     ModeLED(NO_EVENT);
-    CPUdelay(1600);
+    CPUdelay_us(500);
 }
 
-static void Eliteinterrupt() {
-    megaStiEnable = false;
-    PeriodicEvent = false;     // is there an PeriodicEvent?
-    Free_Work_Mode = true;      // Free(WorkModeData)
-
-    initINSBuf();
-    initDATBuf();
-
-    PIN15_setOutputValue(HIGH_Z_MODE, 0); // HIGH Z MODE // 1: close; 0: open;
-
-    instru.VoutGainLv = VOUT_GAIN_15K;
-    VoutGainControl(instru.VoutGainLv);
-    DAC_outputV(Usercode_Correction_to_DAC(instru.VoutGainLv, 25000));
-
-    for (int i = 0; i < SPI_LED_SIZE; i++) {
-        spi_LEDtxbuf[i] = 0;
-        spi_LEDrxbuf[i] = 0;
-    }
-
-    for (int i = 0; i < SPI_DAC_SIZE; i++) {
-        spi_DACtxbuf[i] = 0;
-        spi_rxbuf[i]    = 0;
-    }
-
-    for (int i = 0; i < SPI_ADC_SIZE; i++) {
-        spi_ADC_txbuf[i] = 0;
-        spi_ADC_rxbuf[i] = 0;
-    }
-
-    ModeLED(NO_EVENT);
-    CPUdelay(8000);
-}
 #endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteSPI.h

@@ -8,130 +8,59 @@
 *        exports/tirtos_full_2_14_02_22/docs/doxygen/html/_s_p_i_c_c26_x_x_d_m_a_8h.html
 */
 
-#include <Board.h>
+#include "board.h"
 #include <ti/drivers/SPI.h>
 #include <ti/drivers/dma/UDMACC26XX.h>
 #include <ti/drivers/spi/SPICC26XXDMA.h>
-#include "Elite_PIN.h"
 
-/* application use SPI parameters and buffers */
-#define SPI_LED_SIZE 28
-#define SPI_DAC_SIZE 3
-#define SPI_ADC_SIZE 4
+#define ELITE_VERSION_EIS
 
-static uint16_t spi_LEDtxbuf[SPI_LED_SIZE] = {0};
-static uint16_t spi_LEDrxbuf[SPI_LED_SIZE] = {0};
+#ifdef ELITE_VERSION_EIS
+/* define SPI command */
+// datasheet page 98
+//#define SPICMD_SETADDR  0x20
+//#define SPICMD_WRITEREG 0x2D
+//#define SPICMD_READREG  0x6D
 
-static uint8_t spi_DACtxbuf[SPI_DAC_SIZE] = {0};
-static uint8_t spi_rxbuf[SPI_DAC_SIZE]    = {0};
+//define REG
+#define LPDACCON0       0x2128
+#define LPDACSW0        0x2124
+#define LPDACDAT0       0x2120
+#define LPREFBUFCON     0x2050
+#define SWMUX           0x235C
+#define LPTIASW0        0x20E4
+#define SWCON           0x200C
+#define HSDACCON        0x2010
+#define HSDACDAT        0x2048
+#define LPTIACON0       0x20EC
+#define HSTIACON        0x20FC
+#define AFECON          0x2000
+#define DSWFULLCON      0x2150
+#define NSWFULLCON      0x2154
+#define PSWFULLCON      0x2158
+#define TSWFULLCON      0x215C
+#define WGFCW           0x2030
+#define WGPHASE         0x2034
+#define WGOFFSET        0x2038
+#define WGAMPLITUDE     0x203C
+#define WGCON           0x2014
+#define DE0RESCON       0x20F8
+#define ADCCON          0x21A8
+#define DFTCON          0x20D0
+#define ADCFILTERCON    0x2044
+#define PMBW            0x22F0
+#define CLKSEL          0x0414
+#define CLKCON0         0x0408
+#define CLKCON0KEY      0x0420
+#define HSOSCCON        0x20BC
+#define ADCBUFCON       0x238C
+#define HSRTIACON       0x20F0
 
-static uint8_t spi_ADC_txbuf[SPI_ADC_SIZE] = {0};
-static uint8_t spi_ADC_rxbuf[SPI_ADC_SIZE] = {0};
+#define DFTREAL         0x2078
+#define DFTIMAG         0x207C
+#define ADCDAT                               0x2074
+#define RRR_AFE_STATSCON                     0x21C4            /*  AFE Statistics Control */
 
-/* system use SPI parameters */
-static SPI_Handle      spiHandle0 = NULL;  // SPI0  = LED
-static SPI_Handle      spiHandle1 = NULL;  // SPI1  = ADC +DAC
-static SPI_Params      spiParams0;
-static SPI_Params      spiParams1;
-static SPI_Transaction LED_transaction;
-static SPI_Transaction ADC_DAC_transaction;
-
-static void ELITE15_SPI_HOLD();
-static void ELITE15_SPI_CLOSE();
-
-static void Elite_SPI_init(){
-    SPI_init();
-    SPI_Params_init(&spiParams0);
-    spiParams0.bitRate     = 10000000;  // 10M
-    spiParams0.mode        = SPI_MASTER;
-    spiParams0.dataSize    = 16;
-    spiParams0.frameFormat = SPI_POL0_PHA1;
-    spiHandle0 = SPI_open(Board_SPI0, &spiParams0);  // LED SPI
-
-    SPI_Params_init(&spiParams1);
-    spiParams1.bitRate     = 10000000;  // 10M
-    spiParams1.mode        = SPI_MASTER;
-    spiParams1.dataSize    = 8;
-    spiParams1.frameFormat = SPI_POL0_PHA1;
-    spiHandle1 = SPI_open(Board_SPI1, &spiParams1);  // ADC DAC SPI
-}
-
-static void LED_SPI(uint8_t length, uint16_t *spi_txbuf, uint16_t *spi_rxbuf) {
-    LED_transaction.count = length;
-    LED_transaction.txBuf = spi_txbuf;
-    LED_transaction.rxBuf = spi_rxbuf;
-
-    SPI_transfer(spiHandle0, &LED_transaction);
-}
-
-static void ADC_SPI(uint8_t length, uint8_t *spi_txbuf, uint8_t *spi_rxbuf) {
-//    PIN15_setOutputValue(ADC_CS, 0);  // ADC_CS LOW
-    PIN_setOutputValue(pin_handle, LOAD0, 1);
-    PIN_setOutputValue(pin_handle, D6, 0); // ADC_CS LOW
-
-    ADC_DAC_transaction.count = length;
-    ADC_DAC_transaction.txBuf = spi_txbuf;
-    ADC_DAC_transaction.rxBuf = spi_rxbuf;
-
-    SPI_transfer(spiHandle1, &ADC_DAC_transaction);
-
-    PIN_setOutputValue(pin_handle, D6, 1); // ADC_CS HIGH
-    update_latch_status (ADC_CS, 1);
-//    PIN15_setOutputValue(ADC_CS, 1);  // ADC_CS HIGH
-}
-
-static void DAC_SPI(uint8_t length, uint8_t *spi_txbuf, uint8_t *spi_rxbuf) {
-//    PIN15_setOutputValue(DAC_CS, 0);            // DAC_CS LOW
-    PIN_setOutputValue(pin_handle, LOAD0, 1);
-    PIN_setOutputValue(pin_handle, D7, 0); // DAC_CS LOW
-
-    ADC_DAC_transaction.count = length;
-    ADC_DAC_transaction.txBuf = spi_txbuf;
-    ADC_DAC_transaction.rxBuf = spi_rxbuf;
-
-    SPI_transfer(spiHandle1, &ADC_DAC_transaction);
-
-    PIN_setOutputValue(pin_handle, D7, 1); // DAC_CS HIGH
-    update_latch_status (DAC_CS, 1);
-//    PIN15_setOutputValue(DAC_CS, 1);            // DAC_CS HIGH
-}
-
-static void ELITE15_SPI_HOLD() {
-    Elite_SPI_init();
-    #ifdef ELITE_PIN_1_5_RE
-    PIN_setOutputValue(pin_handle, D6, LH.LATCH0[6]);   // ADC_CS
-    PIN_setOutputValue(pin_handle, D7, LH.LATCH0[7]);   // DAC_CS
-    PIN_setOutputValue(pin_handle, D4, LH.LATCH0[4]);   // update HIGH_Z_MODE
-    #endif
-
-    PIN_setOutputValue(pin_handle, LOAD0, 1);
-    PIN_setOutputValue(pin_handle, LOAD1, 0);
-    PIN_setOutputValue(pin_handle, LOAD2, 0);
-}
-static void ELITE15_SPI_CLOSE() {
-    PIN_setOutputValue(pin_handle, LOAD0, 0);
-    PIN_setOutputValue(pin_handle, LOAD1, 0);
-    PIN_setOutputValue(pin_handle, LOAD2, 0);
-
-    SPI_close(spiHandle0);
-    SPI_close(spiHandle1);
-}
-
-/* Elite1.5 Calibration SPI */
-static void CAL_ADC_SPI(uint8_t length, uint8_t *spi_txbuf, uint8_t *spi_rxbuf) {
-//    PIN15_setOutputValue(ADC_CS, 0);  // ADC_CS LOW
-    PIN_setOutputValue(pin_handle, LOAD0, 1);
-    PIN_setOutputValue(pin_handle, D6, 0); // ADC_CS LOW
-
-    ADC_DAC_transaction.count = length;
-    ADC_DAC_transaction.txBuf = spi_txbuf;
-    ADC_DAC_transaction.rxBuf = spi_rxbuf;
-
-    SPI_transfer(spiHandle1, &ADC_DAC_transaction);
-
-    PIN_setOutputValue(pin_handle, D6, 1); // ADC_CS HOGH
-    update_latch_status (ADC_CS, 1);
-//    PIN15_setOutputValue(ADC_CS, 1);  // ADC_CS HIGH
-}
+#endif // ELITE_EIS
 
 #endif // ELITE_SPI

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/EliteWorkData.h

@@ -1,12 +1,10 @@
 /*=============================================================================
  =                          wm.h                                              =
  =============================================================================*/
-#ifndef ELITE_WORK_DATA_H
-#define ELITE_WORK_DATA_H
+#ifndef ELITE_WORK_DATA
+#define ELITE_WORK_DATA
 
-#ifdef  __cplusplus
-extern "C" {
-#endif
+#define CLOCK_ONE_SECOND 10000 // 1s
 
 #include "EliteInstruction.h"
 
@@ -21,62 +19,61 @@ extern "C" {
     bool     _current_direction_up;  \
     uint16_t _cycleNumber
 
-#define MEAS_CURR(_m)      (((struct wm_meas_t *)(_m))->_measureCurrent)
-#define MEAS_VIN(_m)       (((struct wm_meas_t *)(_m))->_measureVin)
-#define MEAS_VOUT(_m)      (((struct wm_meas_t *)(_m))->_measureVout)
-#define MEAS_BAT(_m)       (((struct wm_meas_t *)(_m))->_measureBat)
-#define VOLT_SW(_m)        (((struct wm_meas_t *)(_m))->_VoViSwitch)
-
-struct wm_meas_t {
-    int32_t  _measureCurrent;
-    int32_t  _measureVin;
-    int32_t  _measureVout;
-    int32_t  _measureBat;
-    uint8_t  _VoViSwitch;
+/* member of mode */
+struct wm_eis_ctx_t {
+    uint32_t _f1;
+    uint32_t _f2;
+    uint32_t _fd1;
+    uint32_t _fd2;
+    uint32_t _fmax;
+    uint32_t _fmin;
+    uint8_t  _decades;                 //num of decades in whole
+    uint16_t _ppd;
+    int8_t   _decadeIndex;             //index of decade max is 8
+    int16_t  _sweepIndex;              //index of smaller decade max is 10
+    bool     _direction_up;
+    bool     _in_reset_flag;
+    uint16_t _amp;
+};
+
+struct wm_cf_ctx_t {
+    uint32_t _f1;
+    bool     _in_reset_flag;
+    uint16_t _amp;
 };
 
-/* member of mode */
 struct wm_vo_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
     int32_t _Vset;
     int32_t _Vinit;
 };
 
 struct wm_it_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
-    int32_t _Vset;
-    int32_t _Vinit;
 };
 
 struct wm_vt_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
 };
 
 struct wm_rt_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
     int32_t _Vset;
     int32_t _Vinit;
 };
 
 struct wm_iv_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
     VOUT_PARA;
 };
 
 struct wm_iv_cy_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
     VOUT_PARA;
 };
 
 struct wm_cc_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
     int32_t _Vmax;
     int32_t _Vmin;
     int32_t _Vset;
@@ -86,26 +83,23 @@ struct wm_cc_ctx_t {
 
 struct wm_cv_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
     VOUT_PARA;
+    int32_t _LPRtia;
 };
 
 struct wm_lsv_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
     VOUT_PARA;
 };
 
 struct wm_ca_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
     int32_t _Vinit;
     int32_t _Vset;
 };
 
 struct wm_pulse_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
     int32_t  _Vset;
     int32_t  _sti_v1;
     int32_t  _sti_v2;
@@ -128,84 +122,11 @@ struct wm_pulse_ctx_t {
     uint16_t _sti_lp;
 };
 
-struct wm_uni_pulse_ctx_t {
-    /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
-    int32_t  _Vset;
-
-    int32_t _v0;
-    uint32_t _t_pulse[4];
-    int32_t _v_initial[4];
-    int32_t _v_slope[4];
-    int32_t _v_step[4];
-
-    uint32_t _t_period;
-    uint32_t _t_pa[4];
-
-    uint32_t _t_pulse_min[4];
-    uint32_t _t_pulse_max[4];
-};
-
-struct wm_dpv_ctx_t {
-    /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
-    int32_t  _Vset;
-
-    int32_t _v0;
-    uint32_t _t_pulse[4];
-    int32_t _v_initial[4];
-    int32_t _v_slope[4];
-    int32_t _v_step[4];
-
-    uint32_t _t_period;
-    uint32_t _t_pa[4];
-    int32_t _v_stop;
-    bool _v_curr_direc;
-    int32_t _v_amp;
-
-    uint32_t _t_pulse_min[4];
-    uint32_t _t_pulse_max[4];
-
-    bool _v_direc_init;
-};
-
-struct wm_dpv_advance_ctx_t {
-    /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
-    int32_t  _Vset;
-
-    int32_t _v0;
-    uint32_t _t_pulse[4];
-    int32_t _v_initial[4];
-    int32_t _v_slope[4];
-    int32_t _v_step[4];
-
-    uint32_t _t_period;
-    uint32_t _t_pa[4];
-    int32_t _v_stop;
-    int32_t _v_up;
-    int32_t _v_low;
-    int32_t _v_amp;
-    int32_t _v_1;
-    int32_t _v_2;
-
-    uint32_t _t_pulse_min[4];
-    uint32_t _t_pulse_max[4];
-
-    uint16_t _cycleNumber;
-
-    bool _v_curr_direc;
-    bool _v_direc_init;
-    bool _v_invert_option;
-    bool _v_stop_direction;
-};
-
 struct wm_ocp_ctx_t {
     /* WARNING: please keep MEASURE at first!! */
-    struct wm_meas_t measure;
 };
 
-int wm_init(void);
+int wm_init(void); //(void *instr_ctx);
 int wm_deinit(void);
 void *wm_get(void);
 
@@ -217,22 +138,74 @@ static void *workMode_p = NULL;
 static bool Free_Work_Mode = false;
 
 /* init mode func */
+static int __eis_create(void)
+{
+    struct wm_eis_ctx_t *p;
+    void **wm = &workMode_p;
+
+    p = malloc(sizeof(struct wm_eis_ctx_t));
+    if (!p) return -1;
+
+    p->_f1             = instru.f1;
+    p->_f2             = instru.f2;
+    p->_fmax           = instru.fmax;
+    p->_fmin           = instru.fmin;
+    p->_fd1            = 0; //decade freq 1
+    p->_fd2            = 0; //decade freq 2
+    p->_ppd            = instru.ppd; //points per decade
+    p->_decades        = 0;
+    p->_sweepIndex     = 0;
+    p->_decadeIndex    = 0;
+    p->_direction_up   = true;
+    p->_in_reset_flag  = false;
+    p->_amp            = instru.acamp;
+
+    *wm = p;
+
+    return 0;
+}
+
+static int __cf_create(void)
+{
+    struct wm_cf_ctx_t *p;
+    void **wm = &workMode_p;
+
+    p = malloc(sizeof(struct wm_cf_ctx_t));
+    if (!p) return -1;
+
+    p->_f1             = instru.f1;  //[reg's value]
+    p->_in_reset_flag  = false;
+    p->_amp            = instru.acamp;
+
+    *wm = p;
+
+    return 0;
+}
+
+static int __ca_create(void)
+{
+    struct wm_ca_ctx_t *p;
+    void **wm = &workMode_p;
+
+    p = malloc(sizeof(struct wm_ca_ctx_t));
+    if (!p) return -1;
+
+    p->_Vinit          = (instru.Vinit - 25000) * 4 * 4000; //[5nV]
+    p->_Vset           = 0;
+
+    *wm = p;
+
+    return 0;
+}
+
 static int __vo_create(void)
 {
-    struct wm_meas_t *m;
     struct wm_vo_ctx_t *p;
     void **wm = &workMode_p;
 
     p = malloc(sizeof(struct wm_vo_ctx_t));
     if (!p) return -1;
 
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
     p->_Vinit          = (instru.Vinit - 25000) * 4 * 10000; //[5nV]
     p->_Vset           = 0;
 
@@ -243,23 +216,12 @@ static int __vo_create(void)
 
 static int __it_create(void)
 {
-    struct wm_meas_t *m;
     struct wm_it_ctx_t *p;
     void **wm = &workMode_p;
 
     p = malloc(sizeof(struct wm_it_ctx_t));
     if (!p) return -1;
 
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
-    p->_Vinit          = (instru.Vinit - 25000) * 4 * 10000; //[5nV]
-    p->_Vset           = 0;
-
     *wm = p;
 
     return 0;
@@ -267,20 +229,12 @@ static int __it_create(void)
 
 static int __vt_create(void)
 {
-    struct wm_meas_t *m;
     struct wm_vt_ctx_t *p;
     void **wm = &workMode_p;
 
     p = malloc(sizeof(struct wm_vt_ctx_t));
     if (!p) return -1;
 
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
     *wm = p;
 
     return 0;
@@ -288,21 +242,13 @@ static int __vt_create(void)
 
 static int __rt_create(void)
 {
-    struct wm_meas_t *m;
     struct wm_rt_ctx_t *p;
     void **wm = &workMode_p;
 
     p = malloc(sizeof(struct wm_rt_ctx_t));
     if (!p) return -1;
 
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
-    p->_Vinit          = (instru.Vinit - 25000) * 4 * 10000; //[5nV]
+    p->_Vinit          = (instru.Vinit - 25000) * 4 * 4000; //[5nV]
     p->_Vset           = 0;
 
     *wm = p;
@@ -312,23 +258,15 @@ static int __rt_create(void)
 
 static int __iv_create(void)
 {
-    struct wm_meas_t *m;
     struct wm_iv_ctx_t *p;
     void **wm = &workMode_p;
 
     p = malloc(sizeof(struct wm_iv_ctx_t));
     if (!p) return -1;
 
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
-    p->_Vinit          = (instru.Vinit - 25000) * 4 * 10000; //[5nV]
-    p->_Vmax           = (instru.Vmax  - 25000) * 4 * 10000; //[5nV]
-    p->_Vmin           = (instru.Vmin  - 25000) * 4 * 10000; //[5nV]
+    p->_Vinit          = instru.Vinit; //(instru.Vinit - 25000) * 4 * 10000; //[5nV]
+    p->_Vmax           = instru.Vmax; //(instru.Vmax  - 25000) * 4 * 10000; //[5nV]
+    p->_Vmin           = instru.Vmin; //(instru.Vmin  - 25000) * 4 * 10000; //[5nV]
     p->_Vset           = 0;
     p->_Vstep          = 0;
     p->_direction_up   = true;
@@ -342,20 +280,12 @@ static int __iv_create(void)
 
 static int __iv_cy_create(void)
 {
-    struct wm_meas_t *m;
     struct wm_iv_cy_ctx_t *p;
     void **wm = &workMode_p;
 
     p = malloc(sizeof(struct wm_iv_cy_ctx_t));
     if (!p) return -1;
 
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
     p->_Vinit          = (instru.Vinit - 25000) * 4 * 10000; //[5nV]
     p->_Vmax           = (instru.Vmax  - 25000) * 4 * 10000; //[5nV]
     p->_Vmin           = (instru.Vmin  - 25000) * 4 * 10000; //[5nV]
@@ -372,20 +302,12 @@ static int __iv_cy_create(void)
 
 static int __cc_create(void)
 {
-    struct wm_meas_t *m;
     struct wm_cc_ctx_t *p;
     void **wm = &workMode_p;
 
     p = malloc(sizeof(struct wm_cc_ctx_t));
     if (!p) return -1;
 
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
     p->_Vmax           = (instru.Vmax  - 25000) * 4 * 10000; //[5nV]
     p->_Vmin           = (instru.Vmin  - 25000) * 4 * 10000; //[5nV]
     p->_Vset           = 0;
@@ -400,23 +322,18 @@ static int __cc_create(void)
 
 static int __cv_create(void)
 {
-    struct wm_meas_t *m;
     struct wm_cv_ctx_t *p;
     void **wm = &workMode_p;
 
     p = malloc(sizeof(struct wm_cv_ctx_t));
     if (!p) return -1;
 
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
-	p->_Vinit          = (instru.Vinit - 25000) * 4 * 10000; //[5nV]
-    p->_Vmax           = (instru.Vmax  - 25000) * 4 * 10000; //[5nV]
-    p->_Vmin           = (instru.Vmin  - 25000) * 4 * 10000; //[5nV]
+    p->_Vinit          = (instru.Vinit - 25000) * 4 * 4000; //[5nV]
+    p->_Vmax           = (instru.Vmax - 25000) * 4 * 4000; //[5nV]
+    p->_Vmin           = (instru.Vmin - 25000) * 4 * 4000; //[5nV]
+//    p->_Vinit          = (instru.Vinit - 25000) * 4 * 10000; //[5nV]
+//    p->_Vmax           = (instru.Vmax  - 25000) * 4 * 10000; //[5nV]
+//    p->_Vmin           = (instru.Vmin  - 25000) * 4 * 10000; //[5nV]
     p->_Vset           = 0;
     p->_Vstep          = 0;
     p->_direction_up   = true;
@@ -430,20 +347,12 @@ static int __cv_create(void)
 
 static int __lsv_create(void)
 {
-    struct wm_meas_t *m;
     struct wm_lsv_ctx_t *p;
     void **wm = &workMode_p;
 
     p = malloc(sizeof(struct wm_lsv_ctx_t));
     if (!p) return -1;
 
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
 	p->_Vinit          = (instru.Vinit - 25000) * 4 * 10000; //[5nV]
     p->_Vmax           = (instru.Vmax  - 25000) * 4 * 10000; //[5nV]
     p->_Vmin           = (instru.Vmin  - 25000) * 4 * 10000; //[5nV]
@@ -458,46 +367,14 @@ static int __lsv_create(void)
     return 0;
 }
 
-static int __ca_create(void)
-{
-    struct wm_meas_t *m;
-    struct wm_ca_ctx_t *p;
-    void **wm = &workMode_p;
-
-    p = malloc(sizeof(struct wm_ca_ctx_t));
-    if (!p) return -1;
-
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
-    p->_Vinit          = (instru.Vinit - 25000) * 4 * 10000; //[5nV]
-    p->_Vset           = 0;
-
-    *wm = p;
-
-    return 0;
-}
-
 static int __pulse_create(void)
 {
-    struct wm_meas_t *m;
     struct wm_pulse_ctx_t *p;
     void **wm = &workMode_p;
 
     p = malloc(sizeof(struct wm_pulse_ctx_t));
     if (!p) return -1;
 
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
     p->_Vset           = 0;
     p->_sti_v1         = instru.sti_v1;
     p->_sti_v2         = instru.sti_v2;
@@ -524,217 +401,14 @@ static int __pulse_create(void)
     return 0;
 }
 
-static int __uni_pulse_create(void)
-{
-    struct wm_meas_t *m;
-    struct wm_uni_pulse_ctx_t *p;
-    void **wm = &workMode_p;
-    uint32_t pul_acc = 0;
-    int i;
-
-    p = malloc(sizeof(struct wm_uni_pulse_ctx_t));
-    if (!p) return -1;
-
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
-    p->_Vset           = 0;
-
-    p->_v0             = UC_TO_5NV(instru.v0); //[5nV]
-
-    p->_t_pulse[0]     = instru.t_pulse[0];
-    p->_t_pulse[1]     = instru.t_pulse[1];
-    p->_t_pulse[2]     = instru.t_pulse[2];
-    p->_t_pulse[3]     = instru.t_pulse[3];
-
-    p->_v_initial[0]   = UC_TO_5NV(instru.v_initial[0]); //[5nv]
-    p->_v_initial[1]   = UC_TO_5NV(instru.v_initial[1]); //[5nv]
-    p->_v_initial[2]   = UC_TO_5NV(instru.v_initial[2]); //[5nv]
-    p->_v_initial[3]   = UC_TO_5NV(instru.v_initial[3]); //[5nv]
-
-    p->_v_slope[0]     = instru.v_slope[0];
-    p->_v_slope[1]     = instru.v_slope[1];
-    p->_v_slope[2]     = instru.v_slope[2];
-    p->_v_slope[3]     = instru.v_slope[3];
-
-    p->_v_step[0]      = UC_TO_5NV(instru.v_step[0]); //[5nv]
-    p->_v_step[1]      = UC_TO_5NV(instru.v_step[1]); //[5nv]
-    p->_v_step[2]      = UC_TO_5NV(instru.v_step[2]); //[5nv]
-    p->_v_step[3]      = UC_TO_5NV(instru.v_step[3]); //[5nv]
-
-    p->_t_period = 0;
-
-    for (i=0; i<4; i++) {
-        p->_t_pa[i] = pul_acc + p->_t_pulse[i];
-        pul_acc = p->_t_pa[i];
-        p->_t_period += p->_t_pulse[i];
-    }
-
-    instru.period = p->_t_period;
-
-    p->_t_pulse_min[0]     = (instru.t_pulse[0] - 100) * instru.t_pulse_min[0] / 100 + 50;
-    p->_t_pulse_min[1]     = (instru.t_pulse[1] - 100) * instru.t_pulse_min[1] / 100 + 50;
-    p->_t_pulse_min[2]     = (instru.t_pulse[2] - 100) * instru.t_pulse_min[2] / 100 + 50;
-    p->_t_pulse_min[3]     = (instru.t_pulse[3] - 100) * instru.t_pulse_min[3] / 100 + 50;
-
-    p->_t_pulse_max[0]     = (instru.t_pulse[0] - 100) * instru.t_pulse_max[0] / 100 + 50;
-    p->_t_pulse_max[1]     = (instru.t_pulse[1] - 100) * instru.t_pulse_max[1] / 100 + 50;
-    p->_t_pulse_max[2]     = (instru.t_pulse[2] - 100) * instru.t_pulse_max[2] / 100 + 50;
-    p->_t_pulse_max[3]     = (instru.t_pulse[3] - 100) * instru.t_pulse_max[3] / 100 + 50;
-
-    *wm = p;
-
-    return 0;
-}
-
-static int __dpv_create(void)
-{
-    struct wm_meas_t *m;
-    struct wm_dpv_ctx_t *p;
-    void **wm = &workMode_p;
-    uint32_t pul_acc = 0;
-    int i;
-
-    p = malloc(sizeof(struct wm_dpv_ctx_t));
-    if (!p) return -1;
-
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
-    p->_Vset           = 0;
-
-    p->_v0             = instru.v0; //[5nV]
-    p->_v_stop         = instru.v_stop; //[5nV]
-
-    p->_t_pulse[0]     = instru.t_pulse[0];
-    p->_t_pulse[1]     = instru.t_pulse[1];
-
-    p->_v_initial[0]   = instru.v_initial[0]; //[5nv]
-    p->_v_initial[1]   = instru.v_initial[1]; //[5nv]
-
-    p->_v_slope[0]     = instru.v_slope[0];
-    p->_v_slope[1]     = instru.v_slope[1];
-
-    p->_v_step[0]      = instru.v_step[0]; //[5nv]
-    p->_v_step[1]      = instru.v_step[1]; //[5nv]
-
-    p->_t_period = 0;
-
-    for (i=0; i<4; i++) {
-        p->_t_pa[i] = pul_acc + p->_t_pulse[i];
-        pul_acc = p->_t_pa[i];
-        p->_t_period += p->_t_pulse[i];
-    }
-
-    instru.period = p->_t_period;
-
-    p->_v_direc_init   = instru.directionInit;
-    p->_v_curr_direc = instru.directionInit;
-    p->_v_amp = instru.v_initial[1] - instru.v_initial[0];
-
-    p->_t_pulse_min[0]     = (instru.t_pulse[0] - 100) * instru.t_pulse_min[0] / 100 + 50;
-    p->_t_pulse_min[1]     = (instru.t_pulse[1] - 100) * instru.t_pulse_min[1] / 100 + 50;
-
-    p->_t_pulse_max[0]     = (instru.t_pulse[0] - 100) * instru.t_pulse_max[0] / 100 + 50;
-    p->_t_pulse_max[1]     = (instru.t_pulse[1] - 100) * instru.t_pulse_max[1] / 100 + 50;
-
-    *wm = p;
-
-    return 0;
-}
-
-static int __dpv_advance_create(void)
-{
-    struct wm_meas_t *m;
-    struct wm_dpv_advance_ctx_t *p;
-    void **wm = &workMode_p;
-    uint32_t pul_acc = 0;
-    int i;
-
-    p = malloc(sizeof(struct wm_dpv_advance_ctx_t));
-    if (!p) return -1;
-
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
-    p->_Vset           = 0;
-
-    p->_v0             = instru.v0; //[5nV]
-    p->_v_stop         = instru.v_stop; //[5nV]
-
-    p->_t_pulse[0]     = instru.t_pulse[0];
-    p->_t_pulse[1]     = instru.t_pulse[1];
-
-    p->_v_initial[0]   = instru.v_initial[0]; //[5nv]
-    p->_v_initial[1]   = instru.v_initial[1]; //[5nv]
-
-    p->_v_slope[0]     = instru.v_slope[0];
-    p->_v_slope[1]     = instru.v_slope[1];
-
-    p->_v_step[0]      = instru.v_step[0]; //[5nv]
-    p->_v_step[1]      = instru.v_step[1]; //[5nv]
-
-    p->_t_period = 0;
-
-    for (i=0; i<4; i++) {
-        p->_t_pa[i] = pul_acc + p->_t_pulse[i];
-        pul_acc = p->_t_pa[i];
-        p->_t_period += p->_t_pulse[i];
-    }
-
-    instru.period = p->_t_period;
-
-    p->_v_direc_init   = instru.directionInit;
-    p->_v_curr_direc = instru.directionInit;
-    p->_v_stop_direction = instru.v_stop_direction;
-    p->_v_up = instru.v_up;
-    p->_v_low = instru.v_low;
-    p->_v_amp = instru.v_initial[1] - instru.v_initial[0];
-    p->_v_1 = instru.v_1;
-    p->_v_2 = instru.v_2;
-
-    p->_t_pulse_min[0]     = (instru.t_pulse[0] - 100) * instru.t_pulse_min[0] / 100 + 50;
-    p->_t_pulse_min[1]     = (instru.t_pulse[1] - 100) * instru.t_pulse_min[1] / 100 + 50;
-
-    p->_t_pulse_max[0]     = (instru.t_pulse[0] - 100) * instru.t_pulse_max[0] / 100 + 50;
-    p->_t_pulse_max[1]     = (instru.t_pulse[1] - 100) * instru.t_pulse_max[1] / 100 + 50;
-
-    p->_cycleNumber = instru.cycleNumber;
-    p->_v_invert_option = instru.v_invert_option;
-
-    *wm = p;
-
-    return 0;
-}
-
 static int __ocp_create(void)
 {
-    struct wm_meas_t *m;
     struct wm_ocp_ctx_t *p;
     void **wm = &workMode_p;
 
     p = malloc(sizeof(struct wm_ocp_ctx_t));
     if (!p) return -1;
 
-    m = (struct wm_meas_t *)p;
-    m->_measureCurrent = 0;
-    m->_measureVin     = 0;
-    m->_measureVout    = 0;
-    m->_measureBat     = 0;
-    m->_VoViSwitch     = instru.VoViSwitch;
-
     *wm = p;
 
     return 0;
@@ -748,12 +422,20 @@ int wm_init(void)
     if (*wm) return -1;
 
     switch (mode) {
-        case CURVE_VO:
-            if (__vo_create()) return -2;
+        case CURVE_EIS:
+            if (__eis_create()) return -2;
             break;
 
-        case CURVE_IT:
-            if (__it_create()) return -2;
+        case CURVE_CF:
+            if (__cf_create()) return -2;
+            break;
+
+        case CURVE_CV:
+            if (__cv_create()) return -2;
+            break;
+
+        case CURVE_CA:
+            if (__ca_create()) return -2;
             break;
 
         case CURVE_VT:
@@ -764,55 +446,10 @@ int wm_init(void)
             if (__rt_create()) return -2;
             break;
 
-        case CURVE_IV:
-            if (__iv_create()) return -2;
-            break;
-
-        case CURVE_IV_CY:
-            if (__iv_cy_create()) return -2;
-            break;
-
-        case CURVE_CC:
-            if (__cc_create()) return -2;
-            break;
-
-        case CURVE_CV:
-            if (__cv_create()) return -2;
-            break;
-
-        case CURVE_LSV:
-            if (__lsv_create()) return -2;
-            break;
-
-        case CURVE_CA:
-            if (__ca_create()) return -2;
-            break;
-
-        case CURVE_PULSE:
-            if (__pulse_create()) return -2;
-            break;
-
-        case CURVE_UNI_PULSE:
-            if (__uni_pulse_create()) return -2;
-            break;
-
-        case CURVE_OCP:
-            if (__ocp_create()) return -2;
-            break;
-
-        case CURVE_DPV:
-        case CURVE_DPV_SMPRATE:
-            if (__dpv_create()) return -2;
-            break;
-        case CURVE_DPV_ADVANCE:
-        case CURVE_DPV_ADVANCE_SMPRATE:
-            if (__dpv_advance_create()) return -2;
-            break;
-
         default:
             // printf("DO NOT support!!");
             return -3;
-    }
+    };
 
     return 0;
 }
@@ -838,7 +475,4 @@ void *wm_get(void)
     return wm;
 }
 
-#ifdef  __cplusplus
-}
-#endif
 #endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/Elite_PIN.h

@@ -1,252 +0,0 @@
-
-#ifndef Elite_PIN
-#define Elite_PIN
-
-#include <ti/drivers/pin/PINCC26XX.h>
-#include <Board.h>
-#include <ti/drivers/PIN.h>
-
-//#define ELITE_PIN_1_5
-#define ELITE_PIN_1_5_RE
-
-/* SPI Board */
-#define Board_SPI0_MISO                 PIN_UNASSIGNED
-#define Board_SPI0_MOSI                 D1
-#define Board_SPI0_CLK                  D0
-#define Board_SPI0_CS                   PIN_UNASSIGNED
-
-#define Board_SPI1_MISO                 IOID_1
-#define Board_SPI1_MOSI                 D3
-#define Board_SPI1_CLK                  D2
-#define Board_SPI1_CS                   PIN_UNASSIGNED
-
-#define D0                              IOID_3
-#define D1                              IOID_4
-#define D2                              IOID_5
-#define D3                              IOID_6
-#define D4                              IOID_7
-#define D5                              IOID_8
-#define D6                              IOID_9
-#define D7                              IOID_10
-
-#define LOAD0                           IOID_13
-#define LOAD1                           IOID_12
-#define LOAD2                           IOID_11
-
-#define ADC_CS                          LOAD0, D6
-#define DAC_CS                          LOAD0, D7
-#define ADC_DAC_SPI_MOSI                LOAD0, D3
-#define ADC_DAC_SPI_CLK                 LOAD0, D2
-#define LED_MOSI                        LOAD0, D1
-#define LED_CLK                         LOAD0, D0
-#define MEM_CS                          LOAD0, D5
-
-#ifdef ELITE_PIN_1_5
-#define MEM_HOLD                        LOAD0, D4
-#define HIGH_Z_MODE                     LOAD2, D5
-#endif
-#ifdef ELITE_PIN_1_5_RE
-#define MEM_HOLD                        LOAD1, D0
-#define HIGH_Z_MODE                     LOAD0, D4
-#endif
-
-#define Turnon_I_MID                    LOAD2, D0
-#define Turnon_I_SMALL                  LOAD2, D4
-#define Turnon_I_LARGE                  LOAD2, D1
-#define Turnon_V_SMALL                  LOAD2, D2
-#define Turnon_V_MID                    LOAD2, D3
-#define Turnon_VOUT_SMALL                LOAD2, D7
-#define shutdown_6994                   LOAD2, D6
-
-//#define Turnon10K                       Turnon_I_MID
-//#define Turnon200R                      Turnon_I_LARGE
-
-/* I2C */
-#ifdef ELITE_VERSION_1_4
-#define Board_I2C0_SCL0                 PIN_UNASSIGNED
-#define Board_I2C0_SDA0                 PIN_UNASSIGNED
-#endif
-
-#define switch_on                       IOID_14
-#define enable_10v                      LOAD1, D5
-#define enable_5v                       LOAD1, D6
-
-PIN_Handle       pin_handle;
-static PIN_State ZM_rst;
-
-const PIN_Config BLE_IO[] = {
-//    D0 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-//    D1 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-//    D2 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-//    D3 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    D4 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    D5 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    D6 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    D7 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-
-    LOAD0 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    LOAD1 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    LOAD2 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-
-    switch_on | PIN_INPUT_EN | PIN_PULLDOWN,                                    // to sense switch
-
-    PIN_TERMINATE
-};
-
-static void add_elite_pin() {
-//    PIN_Status elite15_status;
-    PIN_add(pin_handle,
-    D0 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL);
-    PIN_add(pin_handle,
-    D1 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL);
-    PIN_add(pin_handle,
-    D2 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL);
-    PIN_add(pin_handle,
-    D3 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL);
-
-//    if(elite15_status != PIN_SUCCESS) {
-//        LED_color(DARKLED, 0x0F, 0x0F, 0x0F);
-//    }
-}
-
-static void remove_elite_pin() {
-    PIN_close(pin_handle);
-    pin_handle = PIN_open(&ZM_rst, BLE_IO);
-}
-
-/*!
- *  @def    BOOSTXL_CC2650MA_SPIName
- *  @brief  Enum of SPI names on the CC2650 Booster Pack
- */
-typedef enum BOOSTXL_CC2650MA_SPIName {
-    BOOSTXL_CC2650MA_SPI0 = 0,
-    BOOSTXL_CC2650MA_SPI1 = 1,
-
-    BOOSTXL_CC2650MA_SPICOUNT
-} BOOSTXL_CC2650MA_SPIName;
-
-/*
- *  ========================== SPI DMA begin ===================================
- */
-/* Place into subsections to allow the TI linker to remove items properly */
-#if defined(__TI_COMPILER_VERSION__)
-#pragma DATA_SECTION(SPI_config, ".const:SPI_config")
-#pragma DATA_SECTION(spiCC26XXDMAHWAttrs, ".const:spiCC26XXDMAHWAttrs")
-#endif
-
-/* Include drivers */
-#include <ti/drivers/spi/SPICC26XXDMA.h>
-
-/* SPI objects */
-SPICC26XXDMA_Object spiCC26XXDMAObjects[BOOSTXL_CC2650MA_SPICOUNT];
-
-/* SPI configuration structure, describing which pins are to be used */
-const SPICC26XXDMA_HWAttrsV1 spiCC26XXDMAHWAttrs[BOOSTXL_CC2650MA_SPICOUNT] = {
-    {
-        .baseAddr           = SSI0_BASE,
-        .intNum             = INT_SSI0_COMB,
-        .intPriority        = ~0,
-        .swiPriority        = 0,
-        .powerMngrId        = PowerCC26XX_PERIPH_SSI0,
-        .defaultTxBufValue  = 0,
-        .rxChannelBitMask   = 1<<UDMA_CHAN_SSI0_RX,
-        .txChannelBitMask   = 1<<UDMA_CHAN_SSI0_TX,
-        .mosiPin            = Board_SPI0_MOSI,
-        .misoPin            = Board_SPI0_MISO,
-        .clkPin             = Board_SPI0_CLK,
-        .csnPin             = Board_SPI0_CS
-    },
-    {
-        .baseAddr           = SSI1_BASE,
-        .intNum             = INT_SSI1_COMB,
-        .intPriority        = ~0,
-        .swiPriority        = 0,
-        .powerMngrId        = PowerCC26XX_PERIPH_SSI1,
-        .defaultTxBufValue  = 0,
-        .rxChannelBitMask   = 1<<UDMA_CHAN_SSI1_RX,
-        .txChannelBitMask   = 1<<UDMA_CHAN_SSI1_TX,
-        .mosiPin            = Board_SPI1_MOSI,
-        .misoPin            = Board_SPI1_MISO,
-        .clkPin             = Board_SPI1_CLK,
-        .csnPin             = Board_SPI1_CS
-    },
-};
-
-/* SPI configuration structure */
-const SPI_Config SPI_config[] = {
-    {
-         .fxnTablePtr = &SPICC26XXDMA_fxnTable,
-         .object      = &spiCC26XXDMAObjects[0],
-         .hwAttrs     = &spiCC26XXDMAHWAttrs[0]
-    },
-    {
-         .fxnTablePtr = &SPICC26XXDMA_fxnTable,
-         .object      = &spiCC26XXDMAObjects[1],
-         .hwAttrs     = &spiCC26XXDMAHWAttrs[1]
-    },
-    {NULL, NULL, NULL}
-};
-/*
- *  ========================== SPI DMA end =====================================
-*/
-
-
-/*
- *  ============================= I2C Begin=====================================
-*/
-
-#ifdef ELITE_VERSION_1_4
-
-/* Generic I2C instance identifiers */
-#define Board_I2C                   CC2650_MA_I2C0
-/*!
- *  @def    CC2650_LAUNCHXL_I2CName
- *  @brief  Enum of I2C names on the CC2650 dev board
- */
-typedef enum CC2650_MA_I2CName {
-    CC2650_MA_I2C0 = 0,
-
-    CC2650_MA_I2CCOUNT
-} CC2650_MA_I2CName;
-
-/* Place into subsections to allow the TI linker to remove items properly */
-#if defined(__TI_COMPILER_VERSION__)
-#pragma DATA_SECTION(I2C_config, ".const:I2C_config")
-#pragma DATA_SECTION(i2cCC26xxHWAttrs, ".const:i2cCC26xxHWAttrs")
-#endif
-
-/* Include drivers */
-#include <ti/drivers/i2c/I2CCC26XX.h>
-
-/* I2C objects */
-I2CCC26XX_Object i2cCC26xxObjects[CC2650_MA_I2CCOUNT];
-
-/* I2C configuration structure, describing which pins are to be used */
-const I2CCC26XX_HWAttrsV1 i2cCC26xxHWAttrs[CC2650_MA_I2CCOUNT] = {
-    {
-        .baseAddr = I2C0_BASE,
-        .powerMngrId = PowerCC26XX_PERIPH_I2C0,
-        .intNum = INT_I2C_IRQ,
-        .intPriority = ~0,
-        .swiPriority = 0,
-        .sdaPin = Board_I2C0_SDA0,
-        .sclPin = Board_I2C0_SCL0,
-    }
-};
-
-/* I2C configuration structure */
-const I2C_Config I2C_config[] = {
-    {
-        .fxnTablePtr = &I2CCC26XX_fxnTable,
-        .object = &i2cCC26xxObjects[0],
-        .hwAttrs = &i2cCC26xxHWAttrs[0]
-    },
-    {NULL, NULL, NULL}
-};
-/*
- *  ========================== I2C end =========================================
- */
-#endif
-
-#endif
-

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/Elite_batt.h

@@ -1,99 +0,0 @@
-/*
-***********************************************************
-    Read battery's method
-***********************************************************
-1.read_adc_raw_data(RIS_ADC_BAT, spi_ADC_rxbuf, spi_ADC_txbuf);
-  let "spi_ADC_rxbuf" be 8000
-  8000 * 187.5uV * 2 = 3000000uV = 3V ;
-2.AONBatMonBatteryVoltageGet()
-  let "AONBatMonBatteryVoltageGet()" be 768
-  768 * 125 / 320 / 100 = 768 / 256 = 3V ;
-
-if you want to use first method, and get value 768
-conversion: 8000 * 187.5 * 1e-6 * 2 / 125 * 320 * 100 = 768
-         => 8000 * 12 / 125 = 768
-*/
-
-#ifndef HEADSTAGE_BATT_H
-#define HEADSTAGE_BATT_H
-
-#include <driverlib/aon_batmon.h>
-#define MAX_BATTERY_CAPACITY 4200
-
-static uint8_t headstage_battery_percent() {
-    static uint8_t battery_percent = 100;
-    uint8_t  internal_battery_percent;
-    uint32_t internal_batt_sense = AONBatMonBatteryVoltageGet();
-    internal_batt_sense          = (internal_batt_sense * 125) >> 5;
-    internal_batt_sense          = (internal_batt_sense * 100) / MAX_BATTERY_CAPACITY;
-    internal_battery_percent     = internal_batt_sense & 0xFF;
-    if (internal_battery_percent < battery_percent) battery_percent = internal_battery_percent;
-    return battery_percent;
-}
-
-static void headstage_battery_volt(){
-    uint32_t bat_volt = 0;
-
-    read_adc_raw_data(RIS_ADC_BAT, spi_ADC_rxbuf, spi_ADC_txbuf);
-    bat_volt = (uint32_t) (spi_ADC_rxbuf[0] << 8) | (uint32_t) (spi_ADC_rxbuf[1]);
-    bat_volt = bat_volt * 12 / 125; //x  * 187.5 * 1e-6 * 2 / 125 * 320 * 100 ;
-//    bat_volt = (bat_volt - 1) * 187.5 * 2;
-
-    InputNotify(NOTIFY_VOLT_BAT, bat_volt);
-}
-
-static void headstage_temperature(void) {
-    int32_t curTemp = 0;
-
-    curTemp = AONBatMonTemperatureGetDegC();
-    InputNotify(NOTIFY_TEMPERATURE,curTemp);
-}
-
-static bool EliteADCBattery(){
-    static uint8_t ADCSwitch = 0;
-    bool read_adc_flag = false;
-    if(ADCSwitch == 0){ /**read V**/
-        read_adc_raw_data(RIS_ADC_BAT, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADCSwitch++;
-    }
-    else if(ADCSwitch == 1){ /**read V**/
-        read_adc_raw_data(RIS_ADC_BAT, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADCSwitch++;
-    }
-    else if(ADCSwitch == 2){ /**read V(buffer)**/
-        headstage_battery_volt();
-        headstage_temperature();
-        ADCSwitch++;
-        read_adc_flag = true;
-
-    }else if(ADCSwitch == 3){
-        batteryCheck_flag = false;
-        tempCheck_flag = false;
-        ADCSwitch = 0;
-    }
-
-    return read_adc_flag;
-}
-
-static void measureBat(){
-    if(GPT.BatteryCheckCounter >= 50000){//5min=3000000, 5s=50000
-        GPT.BatteryCheckCounter = 0;
-        batteryCheck_flag = true;
-    }
-
-    if(GPT.BatteryADCCounter >= 15 && batteryCheck_flag){
-        GPT.BatteryADCCounter = 0; //To get the data right, ADC must be delay 1.5ms
-        batteryADC_flag = true;
-        if(batteryADC_flag){
-            EliteADCBattery();
-            batteryADC_flag = false;
-        }
-    }
-
-    uint16_t bat = NotifyVoltBat;
-    if( bat < 768 && bat > 20){
-        PIN15_setOutputValue(enable_5v, 0);
-    }
-}
-
-#endif  // HEADSTAGE_BATT_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/Elite_def.h

@@ -10,67 +10,76 @@
 #define VIS_RST                         0xF0
 #define VIS_ASK                         0x30
 #define VIS_STI                         0xC0
-#define VIS_FUH                         0x90
 #define VIS_INT                         0x60
-#define VIS_SHIFT_200K                  0xA0
-#define VIS_SHIFT_10K                   0xE0
-#define VIS_SHIFT_200R                  0x80
 #define VIS_DEVICE_SHINY                0x10
 #define VIS_SHINY_DIS                   0x20
-#define VIS_CC_ZERO                     0x40
 
 // RIS (real instruction)
 enum all_mode_e {
-    CURVE_IV                       =  0x01, // I-V Curve                       //0x10,
-    CURVE_IV_CY                    =  0x02, // Cycle I-V                       //0x20,
-    CURVE_VO                       =  0x03, // Function Generator              //0x30,
-    CURVE_RT                       =  0x04, // R-T Graph                       //0x40,
-    CURVE_VT                       =  0x05, // V-T Graph                       //0x50,
-    CURVE_IT                       =  0x06, // I-T Graph                       //0x60,
-    CURVE_CC                       =  0x07, // Constant Current (CC)           //0xD0,
+    CURVE_IV                       =  0x01, // I-V Curve
+    CURVE_IV_CY                    =  0x02, // Cycle I-V
+    CURVE_VO                       =  0x03, // Function Generator
+    CURVE_RT                       =  0x04, // R-T Graph
+    CURVE_VT                       =  0x05, // V-T Graph
+    CURVE_IT                       =  0x06, // I-T Graph
+    CURVE_CC                       =  0x07, // Constant Current (CC)
     CURVE_OCP                      =  0x08, // Open Circuit Potential (OCP)
-    CURVE_CV                       =  0x09, // Cyclic Voltammetry (CV)         //0xC0,
-    CURVE_LSV                      =  0x0A, // Linear Sweep Voltammetry (LSV)  //0x02,
-    CURVE_CA                       =  0x0B, // Chronoamperometric Graph (CA)   //0x03,
-    CURVE_PULSE                    =  0x0C,                                    //0x94,
-    CURVE_UNI_PULSE                =  0x0D, // universal pulse
-    CURVE_DPV                      =  0x0E,
-    CURVE_DPV_SMPRATE              =  0x0F,
-    CURVE_DPV_ADVANCE              =  0x10,
+    CURVE_CV                       =  0x09, // Cyclic Voltammetry (CV)
+    CURVE_LSV                      =  0x0A, // Linear Sweep Voltammetry (LSV)
+    CURVE_CA                       =  0x0B, // Chronoamperometric Graph (CA)
+    CURVE_CP                       =  0x0C, // Chronopotentiometry (CP)
+    CURVE_UNI_PULSE                =  0x0D, // Pulse Sensing (universal pulse)
+    CURVE_DPV                      =  0x0E, // Differential Pulse Voltammetry (DPV)
+    CURVE_DPV_ADVANCE              =  0x0F,
+    CURVE_DPV_SMPRATE              =  0x10,
     CURVE_DPV_ADVANCE_SMPRATE      =  0x11,
-
-    CURVE_CALI_ADC                 =  0xF1, // Cali ADC - test                 //0x92,
+    CURVE_EIS                      =  0x12, 
+    CURVE_CF                       =  0x13, // Constant Frequency(CF)
 
 
-    SET_SAMPLE_RATE                =  0xE0,                                    //0x70,
-    SET_ADC_DAC_GAIN               =  0xE1,                                    //0x80,
-    SET_PARA                       =  0xE2
+    CURVE_CALI                     =  0xF1,
+////
+    SET_SAMPLE_RATE                =  0xE0,
 };
 
-enum set_para_e {
-    DAC_VOLT                        = 0x01,
-};
-
-enum dev_para_e {
-    VERSION_DEV_TEST                = 0x01,
-    BAT_DEV_TEST                    = 0x02,
-    TEMP_DEV_TEST                   = 0x03,
-    LED_DEV_TEST                    = 0x04,
-};
-
-
 // CIS (control instruction)
 #define CIS_VERSION                     0x40
 #define CIS_VOLT                        0x10
-#define CIS_TEMPERATURE                 0x80
+#define CIS_LED_TEST                    0x70
+#define CIS_CALI                        0x30
+#define CIS_CALI2                       0x90
+
+#define CTL_WRT                         0x20
+#define CTL_RD                          0x21
+#define CTL_RD_DFTR                     0x78
+#define CTL_RD_DFTI                     0x7C
+#define CTL_RD_ADC                      0x7A
+#define CTL_RESET                       0x11
 
 // mode parameter
-#define STEP_TO_VSETRATE(step)   step2VsetRate(step)
+
 #define VMAX(v1,v2)              ((v1 >= v2) ? v1 : v2)
 #define VMIN(v1,v2)              ((v1 < v2)  ? v1 : v2)
 #define VDIRECTION(v1,v2)        ((v1 > v2)  ?  0 : 1)
 #define AFTER_READ_I             0
 #define AFTER_READ_V             1
+#define PARA_1                   0x01
+#define PARA_2                   0x02
+#define PARA_3                   0x03
+#define PARA_4                   0x04
+#define PARA_5                   0x05
+#define PARA_6                   0x06
+#define PARA_7                   0x07
+#define PARA_8                   0x08
+#define PARA_9                   0x09
+#define PARA_10                  0x0A
+#define PARA_11                  0x0B
+#define PARA_12                  0x0C
+#define PARA_13                  0x0D
+#define PARA_14                  0x0E
+#define PARA_15                  0x0F
+#define PARA_16                  0x10
+#define PARA_17                  0x11
 
 //Elite LED
 #define COLOR_BLACK              0x00
@@ -84,17 +93,6 @@ enum dev_para_e {
 #define COLOR_PURPLE             0x08
 #define COLOR_WHITE              0x09
 #define COLOR_YELLOWGREEN        0x0A
-#define COLOR_YELLOW_DARK        0xF3
-#define COLOR_GREEN_DARK         0xF4
-#define COLOR_BLUE_DARK          0xF5
-#define COLOR_CYAN_DARK          0xF6
-#define COLOR_PURPLE_DARK        0xF8
-
-#define LEDPowerON()             Elite_led_color(COLOR_GREEN)
-#define WORKLED()                Elite_led_color(COLOR_CYAN)
-#define KEYLED()                 Elite_led_color(COLOR_YELLOW)
-#define BT_WAIT_LED()            Elite_led_color(COLOR_YELLOWGREEN)
-
 
 #define BT_WAIT                  0x01
 #define NO_EVENT                 0x02
@@ -102,15 +100,4 @@ enum dev_para_e {
 #define WORKING                  0x04
 #define POST_WORK                0x05
 
-#define VALUE_ZERO_TO_ONE(_v)    (_v == 0) ? 1 : _v
-
-//plot_type
-#define IT_PLOT             1
-#define VT_PLOT             2
-#define VOUT_PLOT           3
-#define IIN_VIN_PLOT        4
-#define IIN_VIN_VOUT_PLOT   5
-
-#define CLOCK_ONE_SECOND 10000
-
 #endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/Elite_mode_ADC_DAC.h

@@ -1,908 +1,151 @@
+#include <math.h>
+
 #ifndef ELITE_MODE_ADC_DAC
 #define ELITE_MODE_ADC_DAC
 
-#define Vset instru.Vset
-
-static void volt_out() {
-    static uint16_t DACOutCode;
-    static int32_t DeltaVout;
-
-    if (DACReset) {
-        instru.Vout = Vset;
-    } else {
-        DeltaVout = Vset - (instru.Vout);
-        instru.Vout = instru.Vout + DeltaVout;
-    }
-
-
-    if (instru.Vout >= 1100000000) { //1100000000 = 5.5V
-        instru.Vout = 1100000000;
-    } else if (instru.Vout <= -1000000000) {  //-1000000000 = -5V
-        instru.Vout = -1000000000;
-    }
-
-    instru.VoltConstant = instru.Vout / 40000 + 25000; //5nV=>usercode
-    DACOutCode = Usercode_Correction_to_DAC(instru.VoutGainLv, instru.VoltConstant);
-    DAC_outputV(DACOutCode);
-
+static void freq_out()
+{
+    DAC_outputF(instru.fset);
     return;
 }
 
 static void vscan_volt_out(void)
 {
-    void *wm = wm_get();
-    uint16_t DACOutCode;
-    int32_t DeltaVout;
-    int32_t Vin;
+    if (instru.eliteFxn == CURVE_CV) {
+        struct wm_cv_ctx_t *cv = (struct wm_cv_ctx_t *)wm_get();
+        void *wm = wm_get();
 
-    Vin = MEAS_VIN(wm) * 200;//[5nV]
+        /* in [5nV] ver */
+        DAC_outputV(instru.Vset);
+        InputNotify(NOTIFY_VOLT, instru.Vset/200);
+    } else if (instru.eliteFxn == CURVE_CA) {
+        struct wm_ca_ctx_t *ca = (struct wm_ca_ctx_t *)wm_get();
 
-    if (DACReset) {
-        instru.Vout = Vset + Vin;
-    } else {
-        DeltaVout = Vset - (instru.Vout - Vin);
-        instru.Vout = instru.Vout + DeltaVout;
+        void *wm = wm_get();
+
+        /* in [5nV] ver */
+        DAC_outputV(instru.Vset);
+        InputNotify(NOTIFY_VOLT, instru.Vset/200);
+    } else if (instru.eliteFxn == CURVE_RT) {
+        struct wm_rt_ctx_t *rt = (struct wm_rt_ctx_t *)wm_get();
+
+        void *wm = wm_get();
+
+        /* in [5nV] ver */
+        DAC_outputV(instru.Vset);
+        InputNotify(NOTIFY_VOLT, instru.Vset/200);
     }
 
-    instru.VoltConstant = instru.Vout / 40000 + 25000;//5nV=>usercode
-    DACOutCode = Usercode_Correction_to_DAC(instru.VoutGainLv, instru.VoltConstant);
-    DAC_outputV(DACOutCode);
 
     return;
 }
 
-static void CalcuResistance()
+
+
+static int32_t neg_18bit(int32_t ret)
 {
-    /* Elite 100000 = 100R
-       Elite 1000000 = 1KR
-       Elite 10000000 = 10KR
-       Elite 100000000 = 100KR
-       Elite 1000000000 = 1MR
-     */
+//    if (ret > 131072) {
+//        ret = ret - 262144;
+//    }
+    ret &= 0x3FFFF;
+    if (ret & (1 << 17)) {
+        ret |= 0xFFFC0000;
+    }
 
-    struct wm_rt_ctx_t *rt = (struct wm_rt_ctx_t *)wm_get();
-    struct wm_meas_t *m = &rt->measure;
-    int64_t resist;
-    int64_t volt = instru.Vout / 200; // [uV]
-    int64_t current = (int64_t)(m->_measureCurrent);
-
-    resist = volt * 1000000 / current; //R = V / Iin; [mOhm]
-    InputNotify(NOTIFY_IMPEDANCE, resist);
+    return ret;
 }
 
-static void DACenable(uint8_t afterRead){
+//////EIS PLOT RELATED FUNCTION END//////
+
+
+static void DACenable(uint8_t afterRead)
+{
     void *wm = wm_get();
 
     if (afterRead == AFTER_READ_I) {
         switch (instru.eliteFxn) {
-            case CURVE_CC:
-                cc_vscan();
-                volt_out();
-                break;
-
-            case CURVE_UNI_PULSE:
-                volt_out();
-                break;
 
             default:
                 break;
         }
     } else if (afterRead == AFTER_READ_V) {
         switch (instru.eliteFxn) {
-            case CURVE_IV_CY:
-            case CURVE_IV:
-            case CURVE_IT:
-            case CURVE_VO:
-                volt_out();
-                break;
-
-            case CURVE_RT:
-                volt_out();
-                CalcuResistance();
+            case CURVE_EIS:
+            case CURVE_CF:
+                freq_out();
                 break;
 
             case CURVE_CV:
             case CURVE_CA:
-            case CURVE_LSV:
-            case CURVE_DPV:
-            case CURVE_DPV_SMPRATE:
-            case CURVE_DPV_ADVANCE:
-            case CURVE_DPV_ADVANCE_SMPRATE:
-                vscan_volt_out();
+                
                 break;
 
             default:{
+                led_color_set(LED_NB_MAX, LED_BR_LV1, LED_CLR_MAGENTA);
                 break;
             }
         }
     }
 }
 
-/*
- * define how long damping time for manual current stalls, to skip damping time
- * any level switch to 0 level has 80ms damping time
- * any level switch to 1 level has 20ms damping time
- * any level switch to 2 level has 10ms damping time
- * any level switch to 3 level has 10ms damping time
- */
-#define CNT_TO_I_GAIN_3M_IIN_VIN_VOUT_PLOT      7   // 7 * 12ms = 84ms
-#define CNT_TO_I_GAIN_100K_IIN_VIN_VOUT_PLOT    2   // 2 * 12ms = 24ms
-#define CNT_TO_I_GAIN_3K_IIN_VIN_VOUT_PLOT      1   // 1 * 12ms = 12ms
-#define CNT_TO_I_GAIN_100R_IIN_VIN_VOUT_PLOT    1   // 1 * 12ms = 12ms
-
-#define CNT_TO_I_GAIN_3M_IIN_VIN_PLOT           10  // 10 * 8ms = 80ms
-#define CNT_TO_I_GAIN_100K_IIN_VIN_PLOT         3   // 3 * 8ms = 24ms
-#define CNT_TO_I_GAIN_3K_IIN_VIN_PLOT           2   // 2 * 8ms = 16ms
-#define CNT_TO_I_GAIN_100R_IIN_VIN_PLOT         2   // 2 * 8ms = 16ms
-
-#define CNT_TO_I_GAIN_3M_IT_PLOT                20  // 20 * 4ms = 80ms
-#define CNT_TO_I_GAIN_100K_IT_PLOT              5   // 5 * 4ms = 20ms
-#define CNT_TO_I_GAIN_3K_IT_PLOT                3   // 3 * 4ms = 12ms
-#define CNT_TO_I_GAIN_100R_IT_PLOT              3   // 3 * 4ms = 12ms
-
-static void read_Iin_change_gain(uint16_t plot_type)
-{
-    /*  read Iin and cali value save as MEAS_CURR(wm)
-     *  if auto gain:
-     *      do NOT record the Iin after changing gain, time is according to damping time
-     *  if static gain:
-     *      change gain if gain is different from last gain
-     */
-    uint16_t plot = plot_type;
-    static uint16_t no_rec_time = 0;
-    static uint8_t cnt = 0;
-    void *wm = wm_get();
-
-    if (instru.IinADCAutoGainEn > 1)
-        return;
-
-    read_adc_raw_data(RIS_ADC_IIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-    MEAS_CURR(wm) = DecodeADCValue(instru.IinADCGainLv, RIS_ADC_IIN, spi_ADC_rxbuf);
-
-    if (instru.IinADCAutoGainEn) {
-        AutoGainChangeIin(MEAS_CURR(wm), plot, &no_rec_time);
-
-    } else {
-        if (lastIinADCGainLevel != instru.IinADCGainLv) {
-            IinADCGainCtrl(instru.IinADCGainLv);
-
-            if (plot_type == IT_PLOT) {
-                if (instru.IinADCGainLv == I_GAIN_3K) {
-                    no_rec_time = CNT_TO_I_GAIN_3K_IT_PLOT;
-                } else if (instru.IinADCGainLv == I_GAIN_100K) {
-                    no_rec_time = CNT_TO_I_GAIN_100K_IT_PLOT;
-                } else if (instru.IinADCGainLv == I_GAIN_3M) {
-                    no_rec_time = CNT_TO_I_GAIN_3M_IT_PLOT;
-                } else {
-                    no_rec_time = CNT_TO_I_GAIN_100R_IT_PLOT;
-                }
-            }
-
-            if (plot_type == IIN_VIN_PLOT) {
-                if (instru.IinADCGainLv == I_GAIN_3K) {
-                    no_rec_time = CNT_TO_I_GAIN_3K_IIN_VIN_PLOT;
-                } else if (instru.IinADCGainLv == I_GAIN_100K) {
-                    no_rec_time = CNT_TO_I_GAIN_100K_IIN_VIN_PLOT;
-                } else if (instru.IinADCGainLv == I_GAIN_3M) {
-                    no_rec_time = CNT_TO_I_GAIN_3M_IIN_VIN_PLOT;
-                } else {
-                    no_rec_time = CNT_TO_I_GAIN_100R_IIN_VIN_PLOT;
-                }
-            }
-
-            if (plot_type == IIN_VIN_VOUT_PLOT) {
-                if (instru.IinADCGainLv == I_GAIN_3K) {
-                    no_rec_time = CNT_TO_I_GAIN_3K_IIN_VIN_VOUT_PLOT;
-                } else if (instru.IinADCGainLv == I_GAIN_100K) {
-                    no_rec_time = CNT_TO_I_GAIN_100K_IIN_VIN_VOUT_PLOT;
-                } else if (instru.IinADCGainLv == I_GAIN_3M) {
-                    no_rec_time = CNT_TO_I_GAIN_3M_IIN_VIN_VOUT_PLOT;
-                } else {
-                    no_rec_time = CNT_TO_I_GAIN_100R_IIN_VIN_VOUT_PLOT;
-                }
-            }
-        }
-    }
-
-    if (curr_rec_en == false) {
-        cnt++;
-    }
-
-    if (cnt >= no_rec_time) {
-        curr_rec_en = true;
-        cnt = 0;
-    }
-
-    return;
-}
-
-static void read_Vin_change_gain(void)
+static void LPTIA_change_gain(void)
 {
     static uint8_t rec_cnt = 0;
     void *wm = wm_get();
 
-    if (instru.IinADCAutoGainEn > 1)
+    if (instru.LPTIAAutoGainEnable > 1)
         return;
 
-    /* read Vin and do NOT record the Vin after changing gain twice */
-    read_adc_raw_data(RIS_ADC_VIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-    MEAS_VIN(wm) = DecodeADCValue(instru.VinADCGainLv, RIS_ADC_VIN, spi_ADC_rxbuf);
-    if (instru.VinADCAutoGainEn) {
-        AutoGainChangeVin(MEAS_VIN(wm));
+    /* read Iin and do NOT record the Iin after changing gain twice */
+    int32_t i;
+    i = read_LPTIA_Iin();
+    if (instru.LPTIAAutoGainEnable) {
+        AutoChangeLPTIAGain(i);
     } else {
-        if (lastVinADCGainLv != instru.VinADCGainLv) {
-            VinADCGainCtrl(instru.VinADCGainLv);
+        if (last_gain_lptia != instru.gain_lv_lptia) {
+              LPTIAGainCtrl(instru.gain_lv_lptia);
         }
     }
 
-    if (volt_rec_en == false) {
+    if (record_flag == false) {
         rec_cnt++;
     }
 
     if (rec_cnt == 2) {
-        volt_rec_en = true;
+        record_flag = true;
         rec_cnt = 0;
     }
 
     return;
 }
 
-static void read_Vout_change_gain(void)
+static void HSTIA_change_gain(void)
 {
-    static uint8_t rec_cnt = 0;
+//    static uint8_t rec_cnt = 0;
     void *wm = wm_get();
 
-    /* read Vout and do NOT record the Vout after changing gain twice */
-    read_adc_raw_data(RIS_ADC_VOUT, spi_ADC_rxbuf, spi_ADC_txbuf);
-    MEAS_VOUT(wm) = DecodeADCValue(0, RIS_ADC_VOUT, spi_ADC_rxbuf);
-
-    if (volt_rec_en == false) {
-        rec_cnt++;
-    }
-
-    if (rec_cnt == 2) {
-        volt_rec_en = true;
-        rec_cnt = 0;
-    }
-
-    return;
-}
-
-void EliteCalcAvg(uint32_t time)
-{
-    struct wm_uni_pulse_ctx_t *p = (struct wm_uni_pulse_ctx_t *)wm_get();
-    struct wm_meas_t *meas = &p->measure;
-    static uint32_t cnt = 0;
-    static int64_t curr_sum = 0;
-    int64_t curr_avg = 0;
-    uint32_t m;
-    uint32_t t = time;
-
-    m = t % p->_t_period;
-
-    if (calc_avg_en) {
-        cnt++;
-        curr_sum = curr_sum + meas->_measureCurrent;
+    if (instru.HSTIAAutoGainEnable > 1)
+        return;
 
+    /* read Iin and do NOT record the Iin after changing gain twice */
+    int32_t i;
+    i = read_HSTIA_Iin();
+    if (instru.HSTIAAutoGainEnable) {
+        AutoChangeHSTIAGain(i);
     } else {
-        curr_avg = curr_sum / cnt;
-        if (cnt == 0) {
-
-            return;
+        if (last_gain_hstia != instru.gain_lv_hstia) {
+            HSTIAGainCtrl(instru.gain_lv_hstia);
         }
-
-        if (m < p->_t_pa[0]) {
-            InputNotify(NOTIFY_CURRENT, curr_avg);
-            SendNotify();
-
-        } else if (m < p->_t_pa[1]) {
-            InputNotify(NOTIFY_VOLT, curr_avg);
-            SendNotify();
-
-        } else if (m < p->_t_pa[2]) {
-
-        } else if (m < p->_t_pa[3]) {
-
-        }
-
-        cnt = 0;
-        curr_sum = 0;
-        curr_avg = 0;
-    }
-
-
-    return;
-}
-
-void dpv_EliteCalcAvg(uint32_t time)
-{
-    struct wm_dpv_ctx_t *p = (struct wm_dpv_ctx_t *)wm_get();
-    struct wm_meas_t *meas = &p->measure;
-    static uint32_t cnt = 0;
-    static int64_t curr_sum = 0;
-    int64_t curr_avg = 0;
-    uint32_t m;
-    uint32_t t = time;
-
-    m = t % p->_t_period;
-    static bool first_v_rec = true;
-
-    if (calc_avg_en) {
-        cnt++;
-        curr_sum = curr_sum + meas->_measureCurrent;
-        if (first_v_rec) {
-            InputNotify(NOTIFY_VOLT, instru.Vout/200 - meas->_measureVin);
-            InputNotify(NOTIFY_IMPEDANCE, instru.Vout/200);
-            first_v_rec = false;
-        }
-
-    } else {
-        first_v_rec = true;
-        curr_avg = curr_sum / cnt;
-        if (cnt == 0) {
-
-            return;
-        }
-
-        if (m < p->_t_pa[0]) {
-            InputNotify(NOTIFY_CURRENT, curr_avg);
-            SendNotify();
-
-        } else if (m < p->_t_pa[1]) {
-            InputNotify(NOTIFY_CURRENT, curr_avg);
-            SendNotify();
-
-        } else if (m < p->_t_pa[2]) {
-
-        } else if (m < p->_t_pa[3]) {
-
-        }
-
-        cnt = 0;
-        curr_sum = 0;
-        curr_avg = 0;
-    }
-
-
-    return;
-}
-
-void dpv_advance_EliteCalcAvg(uint32_t time)
-{
-    struct wm_dpv_advance_ctx_t *p = (struct wm_dpv_advance_ctx_t *)wm_get();
-    struct wm_meas_t *meas = &p->measure;
-    static uint32_t cnt = 0;
-    static int64_t curr_sum = 0;
-    int64_t curr_avg = 0;
-    uint32_t m;
-    uint32_t t = time;
-
-    m = t % p->_t_period;
-    static bool first_v_rec = true;
-
-    if (calc_avg_en) {
-        cnt++;
-        curr_sum = curr_sum + meas->_measureCurrent;
-        if (first_v_rec) {
-            InputNotify(NOTIFY_VOLT, instru.Vout/200 - meas->_measureVin);
-            InputNotify(NOTIFY_IMPEDANCE, instru.Vout/200);
-            first_v_rec = false;
-        }
-
-    } else {
-        first_v_rec = true;
-        curr_avg = curr_sum / cnt;
-        if (cnt == 0) {
-
-            return;
-        }
-
-        if (m < p->_t_pa[0]) {
-            InputNotify(NOTIFY_CURRENT, curr_avg);
-            SendNotify();
-
-        } else if (m < p->_t_pa[1]) {
-            InputNotify(NOTIFY_CURRENT, curr_avg);
-            SendNotify();
-
-        } else if (m < p->_t_pa[2]) {
-
-        } else if (m < p->_t_pa[3]) {
-
-        }
-
-        cnt = 0;
-        curr_sum = 0;
-        curr_avg = 0;
-    }
-
-
-    return;
-}
-
-static void Iin_Vin_Vout_Plot(uint32_t time)
-{
-    static uint8_t ADC_cnt = 0;
-    void *wm = wm_get();
-    uint32_t t = time;
-    bool read_adc_flag = false;
-
-    /* the time for measuring battery */
-    if (batteryCheck_flag && tempCheck_flag) {
-        read_adc_flag = EliteADCBattery();
-        if (!read_adc_flag) {
-             read_adc_raw_data(RIS_ADC_IIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-            ADC_cnt = 5;
-        }
-
-        return;
-    }
-
-    /* the time for Not measuring battery */
-    /* ADC_cnt:  0 - read Iin and do NOT buffer the Iin after changing gain twice,
-     *               and output DAC, and read Vin, and increase ADC_cnt
-     *           1 - read Vin and increase ADC_cnt
-     *           2 - read Vin and do NOT buffer the Vin after changing gain twice,
-     *               and output DAC, and read Vout, and increase ADC_cnt
-     *           3 - read Vout and increase ADC_cnt
-     *           4 - read Vout and do NOT buffer the Vout after changing gain twice,
-     *               and output DAC, and read Iin, and increase ADC_cnt
-     *           5 - read Iin and reset ADC_cnt
-     */
-    if (ADC_cnt == 0) {
-        read_Iin_change_gain(IIN_VIN_VOUT_PLOT);
-
-        if (instru.eliteFxn == CURVE_DPV && vscanReset == false) {
-            dpv_EliteCalcAvg(t);
-        }
-        else if (instru.eliteFxn == CURVE_DPV_ADVANCE && vscanReset == false) {
-            dpv_advance_EliteCalcAvg(t);
-        }
-
-        DACenable(AFTER_READ_I);
-        ADC_cnt++;
-
-    } else if (ADC_cnt == 1) {
-        read_adc_raw_data(RIS_ADC_VIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt++;
-
-    } else if (ADC_cnt == 2) {
-        read_Vin_change_gain();
-        DACenable(AFTER_READ_V);
-        ADC_cnt++;
-
-    } else if (ADC_cnt == 3) {
-        read_adc_raw_data(RIS_ADC_VOUT, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt++;
-
-    } else if (ADC_cnt == 4) {
-        read_Vout_change_gain();
-        DACenable(AFTER_READ_V);
-        ADC_cnt++;
-
-    } else if (ADC_cnt == 5) {
-        read_adc_raw_data(RIS_ADC_IIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt = 0;
     }
 
     return;
 }
 
-static void Iin_Vin_Plot(void)
-{
-    static uint8_t ADC_cnt = 0;
-    void *wm = wm_get();
-    bool read_adc_flag = false;
 
-    /* the time for measuring battery */
-    if (batteryCheck_flag && tempCheck_flag) {
-        read_adc_flag = EliteADCBattery();
-        if (!read_adc_flag) {
-            read_adc_raw_data(RIS_ADC_IIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-            ADC_cnt = 3;
-        }
 
-        return;
-    }
 
-    /* the time for Not measuring battery */
-    /* ADC_cnt:  0 - read Iin and do NOT buffer the Iin after changing gain twice,
-     *               and output DAC, and read Vin, and increase ADC_cnt
-     *           1 - read Vin and increase ADC_cnt
-     *           2 - read Vin and do NOT buffer the Vin after changing gain twice,
-     *               and output DAC, and read Iin, and increase ADC_cnt
-     *           3 - read Iin and reset ADC_cnt
-     */
-    if (ADC_cnt == 0) {
-        read_Iin_change_gain(IIN_VIN_PLOT);
-        DACenable(AFTER_READ_I);
-        ADC_cnt++;
 
-    } else if (ADC_cnt == 1) {
-        read_adc_raw_data(RIS_ADC_VIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt++;
 
-    } else if (ADC_cnt == 2) {
-        read_Vin_change_gain();
-        DACenable(AFTER_READ_V);
-        ADC_cnt++;
 
-    } else if (ADC_cnt == 3) {
-        read_adc_raw_data(RIS_ADC_IIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt = 0;
-    }
-
-    return;
-}
-
-static void IT_Plot(uint32_t time)
-{
-    static uint8_t ADC_cnt = 0;
-    void *wm = wm_get();
-    uint32_t t = time;
-    bool read_adc_flag = false;
-
-    /* measure battery if needs */
-    batteryCheck_flag = false;
-    tempCheck_flag = false;
-
-    if (batteryCheck_flag || tempCheck_flag) {
-        read_adc_flag = EliteADCBattery();
-        if (!read_adc_flag) {
-            read_adc_raw_data(RIS_ADC_IIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-            ADC_cnt = 1;
-        }
-
-        return;
-    }
-
-    /* ADC_cnt:  0 - read Iin and do NOT buffer the Iin after changing gain twice, read Iin and increase ADC_cnt
-     *           1 - read Iin and reset ADC_cnt
-     */
-    if (ADC_cnt == 0) {
-        read_adc_raw_data(RIS_ADC_IIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt++;
-
-        return;
-    }
-
-    if (ADC_cnt == 1) {
-        read_Iin_change_gain(IT_PLOT);
-
-        if (instru.eliteFxn == CURVE_UNI_PULSE && vscanReset == false) {
-            EliteCalcAvg(t);
-        }
-
-        DACenable(AFTER_READ_I);
-        ADC_cnt = 0;
-
-        return;
-    }
-
-    return;
-
-}
-
-static void VT_Plot(void)
-{
-    static uint8_t ADC_cnt = 0;
-    void *wm = wm_get();
-
-    /* measure battery if needs */
-    if (batteryCheck_flag && tempCheck_flag) {
-        EliteADCBattery();
-        if (!batteryCheck_flag) {
-            read_adc_raw_data(RIS_ADC_VIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-            ADC_cnt = 1;
-        }
-
-        return;
-    }
-
-    /* ADC_cnt:  0 - read Vin and do NOT buffer the Vin after changing gain twice, read Vin and increase ADC_cnt
-     *           1 - read Vin and reset ADC_cnt
-     */
-    if (ADC_cnt == 0) {
-        read_adc_raw_data(RIS_ADC_VIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt++;
-
-        return;
-    }
-
-    if (ADC_cnt == 1) {
-        read_Vin_change_gain();
-        DACenable(AFTER_READ_V);
-        ADC_cnt = 0;
-
-        return;
-    }
-
-    return;
-}
-
-static void Vout_Plot(void)
-{
-    static uint8_t ADC_cnt = 0;
-    void *wm = wm_get();
-
-    /* measure battery if needs */
-    if (batteryCheck_flag && tempCheck_flag) {
-        EliteADCBattery();
-        if (!batteryCheck_flag) {
-            read_adc_raw_data(RIS_ADC_VOUT, spi_ADC_rxbuf, spi_ADC_txbuf);
-            ADC_cnt = 1;
-        }
-
-        return;
-    }
-
-    /* ADC_cnt:  0 - read Vout and do NOT buffer the Vout after changing gain twice, read Vout and increase ADC_cnt
-     *           1 - read Vout and reset ADC_cnt
-     */
-    if (ADC_cnt == 0) {
-        read_adc_raw_data(RIS_ADC_VOUT, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt++;
-
-        return;
-    }
-
-    if (ADC_cnt == 1) {
-        read_Vout_change_gain();
-        DACenable(AFTER_READ_V);
-        ADC_cnt = 0;
-
-        return;
-    }
-
-    return;
-}
-
-static void cali_IT_plot(void) {
-    void *wm = wm_get();
-
-    static int32_t ADCValueSUM = 0;
-    static uint16_t cali_count = 0;
-    static uint8_t ADC_cnt = 0;
-    static uint8_t rec_cnt = 0;
-    static uint16_t cali_count_max = 1000;
-    int32_t ADCValueAVG = 0;
-
-    /* ADC_cnt:  0 - read Iin and do NOT buffer the Iin after changing gain twice
-     *           1 - read Iin and increase ADC_cnt
-     *           2 - read Iin and reset ADC_cnt
-     */
-    if (ADC_cnt == 0) {
-        if (instru.IinADCAutoGainEn) {
-            MEAS_CURR(wm) = 0xFFFF;
-        } else {
-            read_adc_raw_data(RIS_ADC_IIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-            MEAS_CURR(wm) = (int32_t) (spi_ADC_rxbuf[0] << 8) | (int32_t) (spi_ADC_rxbuf[1]);
-            if (lastIinADCGainLevel != instru.IinADCGainLv) {
-                IinADCGainCtrl(instru.IinADCGainLv);
-            }
-        }
-
-        if (instru.IinADCGainLv == 0) {
-            cali_count_max = 5000;
-        } else {
-            cali_count_max = 1000;
-        }
-
-        if (curr_rec_en == false) {
-            rec_cnt++;
-        } else {
-            if (cali_count >= cali_count_max) {
-                ADCValueAVG = ADCValueSUM / cali_count;
-
-                InputNotify(NOTIFY_CURRENT, ADCValueAVG);
-                SendNotify();
-
-                uint8_t CIS_buf[9]   = {0};
-                CIS_buf[0] = 5; //data len
-                CIS_buf[1] = instru.chip_id;
-                CIS_buf[2] = (uint8_t) ((ADCValueAVG & 0xFF00) >> 8);
-                CIS_buf[3] = (uint8_t) (ADCValueAVG & 0x00FF);
-                CIS_buf[4] = 0x00;
-                CIS_buf[5] = instru.IinADCGainLv;
-                SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, 9, CIS_buf);
-
-                PeriodicEvent = false;
-                ADCValueSUM = 0;
-                cali_count = 0;
-                ModeLED(NO_EVENT);
-            } else {
-                cali_count++;
-                ADCValueSUM = ADCValueSUM + MEAS_CURR(wm);
-                InputNotify(NOTIFY_CURRENT, MEAS_CURR(wm));
-                InputNotify(NOTIFY_VOLT, ADCValueSUM);
-                InputNotify(NOTIFY_IMPEDANCE, (int32_t)cali_count);
-            }
-        }
-
-        if (rec_cnt == 2) {
-            curr_rec_en = true;
-            rec_cnt = 0;
-        }
-        ADC_cnt++;
-
-        return;
-    }
-
-    if (ADC_cnt == 1) {
-        read_adc_raw_data(RIS_ADC_IIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt++;
-
-        return;
-    }
-
-    if (ADC_cnt == 2) {
-        read_adc_raw_data(RIS_ADC_IIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt = 0;
-
-        return;
-    }
-
-    return;
-}
-
-static void cali_VT_plot(void) {
-    void *wm = wm_get();
-
-    static int32_t ADCValueSUM = 0;
-    static uint16_t cali_count = 0;
-    static uint8_t ADC_cnt = 0;
-    static uint8_t rec_cnt = 0;
-    uint16_t cali_count_max = 0;
-    int32_t ADCValueAVG = 0;
-
-    /* ADC_cnt:  0 - read Vin and do NOT buffer the Vin after changing gain twice
-     *           1 - read Vin and increase ADC_cnt
-     *           2 - read Vin and reset ADC_cnt
-     */
-    if (ADC_cnt == 0) {
-        if (instru.VinADCAutoGainEn) {
-            MEAS_VIN(wm) = 0xFFFF;
-        } else {
-            read_adc_raw_data(RIS_ADC_VIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-            MEAS_VIN(wm) = (int32_t) (spi_ADC_rxbuf[0] << 8) | (int32_t) (spi_ADC_rxbuf[1]);
-            if (lastVinADCGainLv != instru.VinADCGainLv) VinADCGainCtrl(instru.VinADCGainLv);
-        }
-
-        if (instru.VinADCGainLv == 0) {
-            cali_count_max = 5000;
-        } else {
-            cali_count_max = 1000;
-        }
-
-        if (volt_rec_en == false) {
-           rec_cnt++;
-        } else {
-            if (cali_count >= cali_count_max) {
-                ADCValueAVG = ADCValueSUM / cali_count;
-
-                InputNotify(NOTIFY_VOLT, ADCValueAVG);
-                SendNotify();
-
-                uint8_t CIS_buf[9]   = {0};
-                CIS_buf[0] = 5; //data len
-                CIS_buf[1] = instru.chip_id;
-                CIS_buf[2] = (uint8_t) ((ADCValueAVG & 0xFF00) >> 8);
-                CIS_buf[3] = (uint8_t) (ADCValueAVG & 0x00FF);
-                CIS_buf[4] = 0x00;
-                CIS_buf[5] = instru.VinADCGainLv;
-                SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, 9, CIS_buf);
-
-                PeriodicEvent = false;
-                ADCValueSUM = 0;
-                cali_count = 0;
-                ModeLED(NO_EVENT);
-            } else {
-                cali_count++;
-                ADCValueSUM = ADCValueSUM + MEAS_VIN(wm);
-                InputNotify(NOTIFY_VOLT, MEAS_VIN(wm));
-                InputNotify(NOTIFY_CURRENT, ADCValueSUM);
-                InputNotify(NOTIFY_IMPEDANCE, (int32_t)cali_count);
-            }
-        }
-
-        if (rec_cnt == 2) {
-            volt_rec_en = true;
-            rec_cnt = 0;
-        }
-        ADC_cnt++;
-
-        return;
-    }
-
-    if (ADC_cnt == 1) {
-        read_adc_raw_data(RIS_ADC_VIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt++;
-
-        return;
-    }
-
-    if (ADC_cnt == 2) {
-        read_adc_raw_data(RIS_ADC_VIN, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt = 0;
-
-        return;
-    }
-
-    return;
-}
-static void cali_Vout_plot(void) {
-    void *wm = wm_get();
-
-    static int32_t ADCValueSUM = 0;
-    static uint16_t cali_count = 0;
-    static uint8_t ADC_cnt = 0;
-    static uint8_t rec_cnt = 0;
-    uint16_t cali_count_max = 1000;
-    int32_t ADCValueAVG = 0;
-
-    /* ADC_cnt:  0 - read Vin and do NOT buffer the Vin after changing gain twice
-     *           1 - read Vin and increase ADC_cnt
-     *           2 - read Vin and reset ADC_cnt
-     */
-    if (ADC_cnt == 0) {
-
-        read_adc_raw_data(RIS_ADC_VOUT, spi_ADC_rxbuf, spi_ADC_txbuf);
-        MEAS_VOUT(wm) = (int32_t) (spi_ADC_rxbuf[0] << 8) | (int32_t) (spi_ADC_rxbuf[1]);
-
-        if (volt_rec_en == false) {
-           rec_cnt++;
-        } else {
-            if (cali_count >= cali_count_max) {
-                ADCValueAVG = ADCValueSUM / cali_count;
-
-                InputNotify(NOTIFY_VOLT, ADCValueAVG);
-                SendNotify();
-
-                uint8_t CIS_buf[9]   = {0};
-                CIS_buf[0] = 5; //data len
-                CIS_buf[1] = instru.chip_id;
-                CIS_buf[2] = (uint8_t) ((ADCValueAVG & 0xFF00) >> 8);
-                CIS_buf[3] = (uint8_t) (ADCValueAVG & 0x00FF);
-                CIS_buf[4] = 0x00;
-                CIS_buf[5] = instru.VinADCGainLv;
-                SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, 9, CIS_buf);
-
-                PeriodicEvent = false;
-                ADCValueSUM = 0;
-                cali_count = 0;
-                ModeLED(NO_EVENT);
-            } else {
-                cali_count++;
-                ADCValueSUM = ADCValueSUM + MEAS_VOUT(wm);
-                InputNotify(NOTIFY_VOLT, MEAS_VOUT(wm));
-                InputNotify(NOTIFY_CURRENT, ADCValueSUM);
-                InputNotify(NOTIFY_IMPEDANCE, (int32_t)cali_count);
-            }
-        }
-
-        if (rec_cnt == 2) {
-            volt_rec_en = true;
-            rec_cnt = 0;
-        }
-        ADC_cnt++;
-
-        return;
-    }
-
-    if (ADC_cnt == 1) {
-        read_adc_raw_data(RIS_ADC_VOUT, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt++;
-
-        return;
-    }
-
-    if (ADC_cnt == 2) {
-        read_adc_raw_data(RIS_ADC_VOUT, spi_ADC_rxbuf, spi_ADC_txbuf);
-        ADC_cnt = 0;
-
-        return;
-    }
-
-    return;
-}
 #endif
+

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/Elite_power.h

@@ -1,9 +0,0 @@
-#ifndef HEADSTAGE_POWER_H
-#define HEADSTAGE_POWER_H
-
-#include <ti/drivers/Power.h>
-#include <ti/drivers/power/PowerCC26XX.h>
-
-#define headstage_power_shutdown() Power_shutdown(NULL, 0)
-
-#endif // HEADSTAGE_POWER_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/Elite_version.h

@@ -1,15 +1,10 @@
+#ifndef VERSION_DATE		
+#define VERSION_DATE		
 
-#ifndef VERSION_DATE
-#define VERSION_DATE
-
-#define VERSION_DATE_YEAR      22
-#define VERSION_DATE_MONTH     4
-#define VERSION_DATE_DAY       13
-#define VERSION_DATE_HOUR      14
-#define VERSION_DATE_MINUTE    16
-
-// this is NOT the version hash !!
-// it's the last version hash
-#define VERSION_HASH           8808490caa465cc94d14896de28763a5e5c4672b
-#define VERSION_GIT_BRANCH     Elite_OBJ_0.2mv
+#define VERSION_DATE_YEAR		23
+#define VERSION_DATE_MONTH		4
+#define VERSION_DATE_DAY		21
+#define VERSION_DATE_HOUR		14
+#define VERSION_DATE_MINUTE		33
 #endif
+

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/eis_cali_cis.h

@@ -0,0 +1,712 @@
+#include "eis_cali_table.h"
+
+#define CALI_SIZE   BLE_CIS_BUFF_SIZE
+
+uint8_t check_sum(uint8_t message[], int nBytes)
+{
+    uint8_t sum = 0;
+
+    while (nBytes-- > 0) {
+        sum += *(message++);
+    }
+
+    return sum;
+
+}
+
+static void send_cali_version(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+
+    ctx[index++] = len-1;
+    ctx[index++] = instru.chip_id;
+    ctx[index++] = (uint8_t)(CALI_VERSION >> 8);
+    ctx[index++] = (uint8_t)(CALI_VERSION);
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain0_hstia(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_a >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_a >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_a >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_a);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_b >> 56);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_b >> 48);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_b >> 40);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_b >> 32);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_b >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_b >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_b >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].hstia_b);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].rolloff >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].rolloff >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].rolloff >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[0][0].rolloff);
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain0_phase_freq0_freq1(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 0;
+    uint8_t freq_lv_to = 1;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain0_phase_freq2_freq3(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 2;
+    uint8_t freq_lv_to = 3;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[0][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain1_hstia(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_a >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_a >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_a >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_a);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_b >> 56);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_b >> 48);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_b >> 40);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_b >> 32);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_b >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_b >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_b >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].hstia_b);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].rolloff >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].rolloff >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].rolloff >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[1][0].rolloff);
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain1_phase_freq0_freq1(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 0;
+    uint8_t freq_lv_to = 1;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain1_phase_freq2_freq3(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 2;
+    uint8_t freq_lv_to = 3;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[1][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain2_hstia(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_a >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_a >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_a >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_a);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_b >> 56);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_b >> 48);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_b >> 40);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_b >> 32);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_b >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_b >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_b >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].hstia_b);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].rolloff >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].rolloff >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].rolloff >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[2][0].rolloff);
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain2_phase_freq0_freq1(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 0;
+    uint8_t freq_lv_to = 1;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[2][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[2][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[2][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[2][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[2][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[2][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[2][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[2][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain2_phase_freq2_freq3(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 2;
+    uint8_t freq_lv_to = 3;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t) (CaliTable.phase[2][i].coeff >> 24);
+        ctx[index++] = (uint8_t) (CaliTable.phase[2][i].coeff >> 16);
+        ctx[index++] = (uint8_t) (CaliTable.phase[2][i].coeff >> 8);
+        ctx[index++] = (uint8_t) (CaliTable.phase[2][i].coeff);
+        ctx[index++] = (uint8_t) (CaliTable.phase[2][i].offset >> 24);
+        ctx[index++] = (uint8_t) (CaliTable.phase[2][i].offset >> 16);
+        ctx[index++] = (uint8_t) (CaliTable.phase[2][i].offset >> 8);
+        ctx[index++] = (uint8_t) (CaliTable.phase[2][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain3_hstia(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_a >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_a >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_a >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_a);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_b >> 56);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_b >> 48);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_b >> 40);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_b >> 32);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_b >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_b >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_b >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].hstia_b);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].rolloff >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].rolloff >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].rolloff >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[3][0].rolloff);
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain3_phase_freq0_freq1(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 0;
+    uint8_t freq_lv_to = 1;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain3_phase_freq2_freq3(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 2;
+    uint8_t freq_lv_to = 3;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[3][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain4_hstia(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_a >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_a >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_a >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_a);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_b >> 56);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_b >> 48);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_b >> 40);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_b >> 32);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_b >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_b >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_b >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].hstia_b);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].rolloff >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].rolloff >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].rolloff >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[4][0].rolloff);
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain4_phase_freq0_freq1(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 0;
+    uint8_t freq_lv_to = 1;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain4_phase_freq2_freq3(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 2;
+    uint8_t freq_lv_to = 3;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[4][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain5_hstia(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_a >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_a >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_a >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_a);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_b >> 56);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_b >> 48);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_b >> 40);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_b >> 32);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_b >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_b >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_b >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].hstia_b);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].rolloff >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].rolloff >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].rolloff >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[5][0].rolloff);
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain5_phase_freq0_freq1(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 0;
+    uint8_t freq_lv_to = 1;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain5_phase_freq2_freq3(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 2;
+    uint8_t freq_lv_to = 3;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[5][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain6_hstia(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_a >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_a >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_a >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_a);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_b >> 56);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_b >> 48);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_b >> 40);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_b >> 32);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_b >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_b >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_b >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].hstia_b);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].rolloff >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].rolloff >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].rolloff >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[6][0].rolloff);
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain6_phase_freq0_freq1(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 0;
+    uint8_t freq_lv_to = 1;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain6_phase_freq2_freq3(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 2;
+    uint8_t freq_lv_to = 3;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[6][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain7_hstia(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_a >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_a >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_a >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_a);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_b >> 56);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_b >> 48);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_b >> 40);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_b >> 32);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_b >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_b >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_b >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].hstia_b);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].rolloff >> 24);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].rolloff >> 16);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].rolloff >> 8);
+    ctx[index++] = (uint8_t)(CaliTable.hstia_current[7][0].rolloff);
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain7_phase_freq0_freq1(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 0;
+    uint8_t freq_lv_to = 1;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}
+
+static void send_cali_gain7_phase_freq2_freq3(void)
+{
+    uint8_t len = CALI_SIZE;
+    uint8_t ctx[CALI_SIZE] = {0};
+    uint8_t index = 0;
+    uint8_t freq_lv_from = 2;
+    uint8_t freq_lv_to = 3;
+
+    ctx[index++] = len - 1;
+    ctx[index++] = instru.chip_id;
+    for (int i=freq_lv_from; i<=freq_lv_to; i++) {
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].coeff >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].coeff >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].coeff >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].coeff);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].offset >> 24);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].offset >> 16);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].offset >> 8);
+        ctx[index++] = (uint8_t)(CaliTable.phase[7][i].offset);
+    }
+    ctx[len-1] = check_sum(ctx, len);
+
+    SimpleProfile_SetParameter(BLE_CIS_BUFF_CHAR, CALI_SIZE, ctx);
+
+    return;
+}

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/headstage_tni.h

@@ -1,311 +0,0 @@
-
-#ifndef HEADSTAGE_H
-#error "headstage.h not include"
-#endif
-
-#ifdef HEADSTAGE_H_H
-#error "headstage_*.h has be included"
-#endif
-
-#ifndef HEADSTAGE_TNI_H
-#define HEADSTAGE_H_H
-#define HEADSTAGE_TNI_H
-
-// product information
-#define DEVICE_NAME "Elite-v0.1"
-#define MAJOR_PRODUCT_NUMBER 0
-#define MINOR_PRODUCT_NUMBER 1
-#define MAJOR_VERSION_NUMBER 0
-#define MINOR_VERSION_NUMBER 1
-
-// header
-#include <ti/drivers/PIN.h>
-#include "board.h"
-
-/*============
- ==== SPI ====
- ===========*/
-
-/* application use SPI parameters and buffers */
-
-#define SPI_BUFFER_SIZE 16
-
-/**
-* the pointer to point which channel is used currently.
-* -1 for not beginning.
-*/
-static int8    channel_pointer            = -1;
-
-static uint8_t spi_txbuf[SPI_BUFFER_SIZE] = {0};
-static uint8_t spi_rxbuf[SPI_BUFFER_SIZE] = {0};
-
-/*=============================
- ==== headstage variable ====
- ============================*/
-
-PIN_Handle       pin_handle;
-static PIN_State DBS_rst;
-
-// DBS reset pin
-
-const PIN_Config BLE_IO[] = {
-    //
-    IOID_9 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    IOID_2 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    IOID_3 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    IOID_13 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL,
-    PIN_TERMINATE  //
-};
-
-/**
- * ADC clock switch signal.
- */
-static bool adc_clock_signal = FALSE;
-
-/*=======================================
- ==== headstage function declaration ====
- ======================================*/
-
-static void headstage_tni_update_instruction_callback(uint8_t ins_type, uint8_t ins_op, uint8_t ins_len, uint8_t *ins);
-
-/*=============================
- ==== ramp data generating ====
- ============================*/
-
-static uint16_t ramp_data_counter = 0;
-
-static void create_ramp(uint8_t *buff) {
-    buff[0] = 0b10110000 | (0b00001111 & (uint8_t)(ramp_data_counter >> 6));
-    buff[1] = (uint8_t)(ramp_data_counter << 2);
-    ramp_data_counter += 1;
-}
-
-/*=======================================
- ==== headstage function implemented ====
- ======================================*/
-
-/**
- * change channel value to little endian
- */
-static uint8 encode_channel(uint8 channel) {
-    return 0x0F & (((channel & 0b1000) >> 3) |  //
-                   ((channel & 0b0100) >> 1) |  //
-                   ((channel & 0b0010) << 1) |  //
-                   ((channel & 0b0001) << 3));
-}
-
-static void headstage_init() {
-    set_update_instruction_callback(headstage_tni_update_instruction_callback);
-
-    // initialize the DBS reset pin
-    pin_handle = PIN_open(&DBS_rst, BLE_IO);
-    PIN_setOutputValue(pin_handle, IOID_9, 1);
-    PIN_setOutputValue(pin_handle, IOID_2, 0);
-    PIN_setOutputValue(pin_handle, IOID_3, 0);
-}
-
-/**
- * change the recording clock bit in the instruction buffer.
- */
-static void update_ins_rec_clock(uint8_t *buf, bool adc_clock_signal) {
-    buf[3] = (buf[3] & 0b11110000) | ((adc_clock_signal) ? 0b1000 : 0);
-}
-
-/**
- * change the recording channel bit in the instruction buffer.
- */
-static void update_ins_rec_channel(uint8_t *buf, uint8 channel) {
-    buf[1] = (buf[1] & 0b00001111) | (encode_channel(channel) << 4);
-}
-
-/**
- * change the stimulation enable bit in the instruction buffer.
- */
-static void update_ins_sti_enable(uint8_t *buf, bool enable) {
-    buf[1] = (buf[1] & 0b11111101) | ((enable) ? 0b10 : 0);
-}
-
-/**
- * change the stimulating channel bit in the instruction buffer.
- */
-static void update_ins_sti_channel(uint8_t *buf, uint8 sti_chp, uint8 sti_chn) {
-    buf[2] = (buf[2] & 0b11110000) | encode_channel(sti_chp);
-    buf[3] = (buf[3] & 0b00001111) | (encode_channel(sti_chn) << 4);
-}
-
-static void update_ins_buffer() {
-    uint8 header      = 0b10100000;
-    uint8 amp_gain    = (instru.amp_gain & 0b11) << 3;
-    uint8 amp_lbf     = instru.amp_low_band_freq & 0b111;
-    uint8 channel     = 0;  // should be call update_ins_channel to modify this value
-    uint8 chopper     = (instru.chopper) ? 0b00001000 : 0;
-    uint8 fast_settle = (instru.fast_settle) ? 0b00000100 : 0;
-    uint8 sti_enable  = (instru.work_mode != STI_MODE_DISABLE) ? 0b00000010 : 0;
-    uint8 sti_volt_l  = (instru.sti_volt & 0b11111) >> 4;
-    uint8 sti_volt_h  = (instru.sti_volt & 0b01111) << 4;
-    uint8 sti_chp     = instru.sti_channel_pmos & 0b1111;
-    uint8 sti_chn     = (instru.sti_channel_nmos & 0b1111) << 4;
-    uint8 clk_signal  = 0;  // should be call update_ins_clock to modify this value
-
-    spi_txbuf[0] = header | amp_gain | amp_lbf;
-    spi_txbuf[1] = channel | chopper | fast_settle | sti_enable | sti_volt_l;
-    spi_txbuf[2] = sti_volt_h | sti_chp;
-    spi_txbuf[3] = sti_chn | clk_signal;
-}
-
-static bool update_ins_rec_buffer() {
-    adc_clock_signal = (adc_clock_signal) ? FALSE : TRUE;  // switch adc_clock
-    update_ins_rec_clock(spi_txbuf, adc_clock_signal);
-
-    if (adc_clock_signal) {
-        // change to next channel
-
-        if (next_active_channel()) {
-            update_ins_rec_channel(spi_txbuf, channel_pointer);
-        } else {
-            // no channel active
-            return false;
-        }
-    }
-
-    return true;
-}
-
-/**
- * Change the instruction content for SPI buffer, which is depended on the
- * work_mode. Expend the remind instruction according to the base instruction
- * which allocated at the beginning 4 bytes of the SPI buffer.
- *
- * ========= ===========
- * work_mode ins pattern
- * ========= ===========
- * POS, NEG  4 F  D 0
- * P2N, N2P  4 4' F D
- * AWF       not impl
- * ========= ===========
- *
- * pattern *4*
- *     stimulation instruction.
- *
- * pattern *F*
- *     set pmos channel to 0xF, release the remain voltage in the capacitance.
- *
- * pattern *D*
- *     disable stimulation
- *
- * pattern *0*
- *     nop.
- *
- * @param: buf: pointer of the SPI buffer.
- */
-static void update_ins_sti_buffer() {
-    switch (instru.work_mode) {
-    case STI_MODE_POS:
-    case STI_MODE_NEG:
-        // copy [4:7]
-        spi_txbuf[4] = spi_txbuf[0];
-        spi_txbuf[5] = spi_txbuf[1];
-        spi_txbuf[6] = spi_txbuf[2];
-        spi_txbuf[7] = spi_txbuf[3];
-        // copy [8:B]
-        spi_txbuf[8]  = spi_txbuf[0];
-        spi_txbuf[9]  = spi_txbuf[1];
-        spi_txbuf[10] = spi_txbuf[2];
-        spi_txbuf[11] = spi_txbuf[3];
-        // reset [C:F]
-        spi_txbuf[12] = 0;
-        spi_txbuf[13] = 0;
-        spi_txbuf[14] = 0;
-        spi_txbuf[15] = 0;
-        // change content
-        update_ins_sti_enable(spi_txbuf, TRUE);
-        // ins buf [4:7]
-        update_ins_sti_enable(spi_txbuf + 4, TRUE);
-        update_ins_sti_channel(spi_txbuf + 4, 0xF, instru.sti_channel_pmos);
-        // ins buf [8:B]
-        update_ins_sti_enable(spi_txbuf + 8, FALSE);
-        break;
-    case STI_MODE_P2N:
-    case STI_MODE_N2P:
-        // copy [4:7]
-        spi_txbuf[4] = spi_txbuf[0];
-        spi_txbuf[5] = spi_txbuf[1];
-        spi_txbuf[6] = spi_txbuf[2];
-        spi_txbuf[7] = spi_txbuf[3];
-        // copy [8:B]
-        spi_txbuf[8]  = spi_txbuf[0];
-        spi_txbuf[9]  = spi_txbuf[1];
-        spi_txbuf[10] = spi_txbuf[2];
-        spi_txbuf[11] = spi_txbuf[3];
-        // copy [C:F]
-        spi_txbuf[12] = spi_txbuf[0];
-        spi_txbuf[13] = spi_txbuf[1];
-        spi_txbuf[14] = spi_txbuf[2];
-        spi_txbuf[15] = spi_txbuf[3];
-        // change content
-        update_ins_sti_enable(spi_txbuf + 0, TRUE);
-        update_ins_sti_channel(spi_txbuf + 0, instru.sti_channel_pmos, instru.sti_channel_nmos);
-        // ins buf [4:7]
-        update_ins_sti_enable(spi_txbuf + 4, TRUE);
-        update_ins_sti_channel(spi_txbuf + 4, instru.sti_channel_nmos, instru.sti_channel_pmos);
-        // ins buf [8:B]
-        update_ins_sti_enable(spi_txbuf + 8, TRUE);
-        update_ins_sti_channel(spi_txbuf + 8, 0xF, instru.sti_channel_nmos);
-        // ins buf [C:F]
-        update_ins_sti_enable(spi_txbuf + 12, FALSE);
-        break;
-    case STI_MODE_AWF:
-        // XXX define the voltage change
-        break;
-    default:
-        // do nothing
-        break;
-    }
-}
-
-static void headstage_tni_update_instruction_callback(uint8_t ins_type, uint8_t ins_op, uint8_t ins_len, uint8_t *ins) {
-    switch (ins_type) {
-    case INS_TYPE_VIS: {
-    // reset
-    case VIS_RST:
-        // reset. reset all variable
-        adc_clock_signal = FALSE;
-        memset(spi_txbuf, 0, SPI_BUFFER_SIZE);
-        break;
-
-    // interrupt
-    case VIS_INT:
-        // stop. reset channel table
-        ramp_data_counter = 0;
-        memset(spi_txbuf, 0, SPI_BUFFER_SIZE);
-        break;
-    }
-    case INS_TYPE_RIS:
-    default:
-        break;
-    }
-}
-
-static uint8_t *spi_transact_rec_instruction() {
-    if (IS_REC_MODE(instru.work_mode)) {
-        PIN_setOutputValue(pin_handle, IOID_13, 1);  // DBS_P2S turn on
-        headstage_spi_transaction(SPI_BUFFER_SIZE, spi_txbuf, spi_rxbuf);
-        PIN_setOutputValue(pin_handle, IOID_13, 0);  // DBS_P2S turn off
-
-    } else if (IS_ARM_MODE(instru.work_mode) && !adc_clock_signal) {
-        create_ramp(spi_rxbuf);
-    }
-
-    if (adc_clock_signal) {
-        return NULL;
-    } else {
-        return spi_rxbuf;
-    }
-}
-
-static uint8_t *spi_transact_sti_instruction() {
-    headstage_spi_transaction(16, spi_txbuf, NULL);
-    return NULL;
-}
-
-#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/mode_ca.h

@@ -0,0 +1,69 @@
+#ifndef MODE_CA_H
+#define MODE_CA_H
+
+#ifdef  __cplusplus
+extern "C" {
+#endif
+
+static void decode_ca_mode(uint8 *ins)
+{
+    instru.eliteFxn    = CURVE_CA;
+    instru.Vinit       = (int32_t)ins[3] << 8 | (int32_t)ins[4];  //37500
+    instru.notifyRate  = (uint32_t)ins[7] << 8 | (uint32_t)ins[8];  //1000
+    instru.notifyRate  = 10000 / instru.notifyRate * 10;  //100
+    instru.VsetRate    = VsetRateTable[0]; //2
+    //instru.hign_z_en   = ins[6] & 0x0F;
+
+    //instru.VoutGainLv = VOUT_GAIN_240K;
+
+    setEIS_CV();
+    ModeLED(WORKING);
+
+    return;
+}
+
+static void ca_vscan(void)
+{
+    struct wm_ca_ctx_t *ca = (struct wm_ca_ctx_t *)wm_get();
+
+    if(vscanReset){
+        instru.Vset = ca->_Vinit;
+    }
+
+    if(!vscanReset){
+        instru.Vset = ca->_Vinit;
+    }
+
+    return;
+}
+
+static void CA_Plot(void)
+{
+    struct wm_ca_ctx_t *ca = (struct wm_ca_ctx_t *)wm_get();
+    static uint8_t ADC_cnt = 0;
+    void *wm = wm_get();
+
+    if (ADC_cnt == 0) {
+        LPTIA_change_gain();
+        ADC_cnt++;
+
+    } else if (ADC_cnt == 1) {
+        read_LPTIA_Iin();
+        ADC_cnt = 0;
+    }
+
+    return;
+}
+
+
+static void set_ca_volt(uint8 *ins)
+{
+    struct wm_ca_ctx_t *ca = (struct wm_ca_ctx_t *)wm_get();
+    instru.Vinit = (int32_t)ins[4] << 8 | (int32_t)ins[5];  //37500
+    ca->_Vinit = (instru.Vinit - 25000) * 4 * 4000; //[5nV]
+}
+
+#ifdef  __cplusplus
+}
+#endif
+#endif  // TIMERS_H

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/mode_cf.h

@@ -0,0 +1,156 @@
+
+
+
+
+/***
+DC Volt            0 mv
+AC Amp             100 mv
+Freq               200000Hz~0.1Hz
+Points per decades 10 points
+Point spacing      Logarithm
+Delay              0 points
+Average            2
+Current range      Auto
+
+[CC2650] att_write 360CD10100CB7355000000070000
+[CC2650] att_write 360BD10261A801000004000A00
+***/
+
+#define DECODE_INS_1               0x01
+#define DECODE_INS_2               0x02
+#define DECODE_INS_MODE            0xFF
+
+static void decode_cf_mode(uint8_t *instruction)
+{
+    uint8_t *ins = instruction;
+    uint8_t ins_step = ins[3];
+
+
+    if (ins_step == DECODE_INS_1) {
+        instru.f1            = (uint32_t)ins[4] << 24 | (uint32_t)ins[5] << 16 | (uint32_t)ins[6] << 8 | (uint32_t)ins[7]; //FREQ_START //13333333
+
+        instru.delay         = (uint16_t)ins[12] << 8 | (uint16_t)ins[13]; //DELAY/10 how many periods    //0
+
+        return;
+    }
+
+    if (ins_step == DECODE_INS_2) {
+        instru.dcbias        = (uint16_t)ins[4] << 8 | (uint16_t)ins[5];  //25000
+        instru.acamp         = (uint16_t)ins[6] << 8 | (uint16_t)ins[7];  //256
+        instru.avgnum        = (uint8_t)ins[8];                           //0
+        instru.gain_lv_hstia = (uint8_t)ins[9];                           //4 = HSRTIA_200R                         //0
+
+        return;
+    }
+
+    if (ins_step == DECODE_INS_MODE) {
+        instru.eliteFxn = CURVE_CF;
+        
+        set_hs_only();
+        if (instru.gain_lv_hstia < HSRTIA_MAX) {
+            instru.HSTIAAutoGainEnable = 0;
+            HSTIAGainCtrl(instru.gain_lv_hstia);
+        } else {
+            instru.HSTIAAutoGainEnable = 1;
+            instru.gain_lv_hstia = HSRTIA_200R;
+            HSTIAGainCtrl(instru.gain_lv_hstia);
+        }
+        HSDAC_outputV(instru.dcbias);
+        AD5940_SPIWriteReg(WGFCW, instru.fset);
+        AD5940_SPIWriteReg(WGCON, 0x0); // 0x0: DC disable ac first
+        AD5940_SPIWriteReg(WGAMPLITUDE, instru.acamp);
+        AD5940_SPIWriteReg(WGCON, 0x00000004); //0x4: Sinusoid
+        ModeLED(WORKING);
+
+        return;
+    }
+
+    return;
+}
+
+static void cf_fscan(void)
+{
+    struct wm_cf_ctx_t  *cf = (struct wm_cf_ctx_t  *)wm_get();
+
+    if (vscanReset) {
+        cf->_in_reset_flag = true;
+
+        cf->_f1 = User2Freq(cf->_f1);
+
+        instru.fset = cf->_f1;
+
+        vscanReset = false;
+        SetWGAmp(instru.acamp,instru.fset);
+        DAC_outputF(Freq2DAC(instru.fset)); //[10mHz->Reg's]
+    }
+
+    if (!vscanReset) {
+        instru.fset = cf->_f1;
+    }
+
+    SetSamplingTime(instru.fset);
+
+    instru.sampleRate = 2000;
+}
+
+static void CF_Plot(void) //real and imag impedance plot
+{
+    static uint8_t  avgNumTable[4] = {2, 4, 6, 8};
+    struct wm_cf_ctx_t *cf = (struct wm_cf_ctx_t *)wm_get();
+    static uint8_t ADC_cnt = 0;
+    static int32_t realSum, imagSum = 0;
+    int32_t avg_real, avg_imag = 0;
+    static uint8_t avg_count = 0;
+    void *wm = wm_get();
+
+    if (fout_flag){
+        EnDFTnADC(1);
+        instru.sampleRate = CalcDelayTime(instru.fset);
+        fout_flag = false;
+        if (cf->_in_reset_flag) {
+            avg_count = 0;
+            realSum = 0;
+            imagSum = 0;
+            ADC_cnt = 0;
+            cf->_in_reset_flag = false;
+        }
+    } else {
+        if (ADC_cnt == 0){
+            HSTIA_change_gain();            // ADC measure
+            if (gainChange_flag) {
+                gainChange_flag = false;
+                instru.sampleRate = CalcDelayTime(instru.fset);
+                instru.real = 0;
+                instru.imag = 0;
+                ADC_cnt = 0;
+            } else {
+                instru.sampleRate = 15;
+                ADC_cnt ++;
+            }
+        }
+        else if (ADC_cnt == 1) {
+            realSum += instru.real;
+            imagSum += instru.imag;
+            avg_count++;
+            instru.sampleRate = 15;
+            if (avg_count == avgNumTable[instru.avgnum]){
+                avg_real = realSum / avg_count;
+                avg_imag = imagSum / avg_count;
+
+                InputNotify(NOTIFY_CURRENT, avg_imag);
+                InputNotify(NOTIFY_VOLT, avg_real);
+                InputNotify(NOTIFY_IMPEDANCE, instru.fset);
+                NotifyCh4 = (uint32_t)cf->_amp * 1000 * 800 / 2047; //[uV]
+
+                EnDFTnADC(0);
+                avg_count = 0;
+                realSum = 0;
+                imagSum = 0;
+                notify_flag = true;
+            }
+            ADC_cnt = 0;
+        }
+    }
+
+    return;
+}

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/mode_cv.h

@@ -0,0 +1,175 @@
+
+static void step2VsetRate(uint32_t step){
+    /*step = 100 mv, index = 0, n = 2
+             10  mv, index = 1, n = 10
+             1   mv, index = 2, n = 100
+             0.1 mv, index = 3, n = 1000
+             0.01mv, index = 4, n = 10000  */
+
+    if(step >= 10000){
+        instru.VsetRateIndex = 0;
+    }else if (step >= 1000){
+        instru.VsetRateIndex = 1;
+    }else if (step >= 100){
+        instru.VsetRateIndex = 2;
+    }else if (step >= 10){
+        instru.VsetRateIndex = 3;
+    }else if (step >= 1){
+        instru.VsetRateIndex = 4;
+    }
+}
+
+#define STEP_TO_VSETRATE(step)   step2VsetRate(step)
+
+static void decode_cv_mode(uint8 *ins)
+{
+    if (ins[3] == PARA_1) {
+        instru.Vinit       = (int32_t)ins[4] << 8 | (int32_t)ins[5];
+        instru.Ve1         = (uint16_t)ins[6] << 8 | (uint16_t)ins[7];
+        instru.Ve2         = (uint16_t)ins[8] << 8 | (uint16_t)ins[9];
+        instru.Vmax        = (int32_t)VMAX(instru.Ve1,instru.Ve2);
+        instru.Vmin        = (int32_t)VMIN(instru.Ve1,instru.Ve2);
+        if (instru.Vinit > instru.Ve1 || instru.Vinit == instru.Vmax){
+            instru.directionInit = 0;//0:reverse   1:forward
+        } else if (instru.Vinit <= instru.Ve1 || instru.Vinit == instru.Vmin){
+            instru.directionInit = 1;
+        }
+    } else if (ins[3] == PARA_2) {
+        instru.eliteFxn    = CURVE_CV;
+        instru.notifyRate  = (uint32_t)ins[8] << 8 | (uint32_t)ins[9];
+        instru.notifyRate  = 10000 / instru.notifyRate * 10;
+        //controller UI 0.01~1000mv send to Elite 1~100000
+        instru.step        = (uint32_t)ins[4] << 24 | (uint32_t)ins[5] << 16 | (uint32_t)ins[6] << 8 | (uint32_t)ins[7];
+        STEP_TO_VSETRATE(instru.step); //step2VsetRate
+        instru.VsetRate    = VsetRateTable[instru.VsetRateIndex];//N
+        instru.cycleNumber   = (uint16_t)ins[10] << 8 | (uint16_t)ins[11];
+
+        setEIS_CV();
+        ModeLED(WORKING);
+    }
+
+    return;
+}
+
+static void cv_vscan(void)
+{
+    struct wm_cv_ctx_t *cv = (struct wm_cv_ctx_t *)wm_get();
+    static bool VminCounter;
+    static bool VmaxCounter;
+
+    NotifyCycleNumber = (instru.cycleNumber - cv->_cycleNumber + 1);
+
+    if (vscanReset) {
+        VmaxCounter = false;
+        VminCounter = false;
+
+        if (instru.directionInit == 1) {
+            cv->_direction_up         = true;
+            cv->_current_direction_up = true;
+        } else {
+            cv->_direction_up         = false;
+            cv->_current_direction_up = false;
+        }
+
+//        Vstep = x * 20 * N, x=xmV ; N=VscanRate   Vstep unit [5nV]/[0.1ms]
+        if (instru.step <= 10) {
+            cv->_Vstep = instru.step *  instru.VsetRate / 5;
+        } else {
+            cv->_Vstep = instru.step / 5 *  instru.VsetRate;
+        }
+
+
+        if (cv->_Vmin == cv->_Vinit) {
+            VminCounter = true;
+        }
+        if (cv->_Vmax == cv->_Vinit) {
+            VmaxCounter = true;
+        }
+
+        instru.Vset = cv->_Vinit;
+    }
+
+    if (!vscanReset) {
+        if ((instru.Vinit < instru.Ve1 && instru.Vinit < instru.Ve2) ||
+        (instru.Vinit > instru.Ve1 && instru.Vinit > instru.Ve2)
+        ) {
+            if (cv->_current_direction_up) {
+                instru.Vset += cv->_Vstep; //* GPT.GptimerMultiple;
+            } else {
+                instru.Vset -= cv->_Vstep; //* GPT.GptimerMultiple;
+            }
+
+            if (instru.Vinit < instru.Ve1 && instru.Vinit < instru.Ve2) {
+                if (instru.Vset == cv->_Vmin) {
+                    VminCounter = true;
+                    instru.Vinit = instru.Vmin;
+                    cv->_Vinit = cv->_Vmin;
+                }
+            } else if (instru.Vinit > instru.Ve1 && instru.Vinit > instru.Ve2) {
+                if (instru.Vset == cv->_Vmax) {
+                    VmaxCounter = true;
+                    instru.Vinit = instru.Vmax;
+                    cv->_Vinit = cv->_Vmax;
+                }
+            }
+        } else {
+            if (instru.Vset >= cv->_Vmax) {
+                VmaxCounter = true;
+            } else if (instru.Vset <= cv->_Vmin) {
+                VminCounter = true;
+            }
+
+            if (cv->_current_direction_up) {
+                instru.Vset += cv->_Vstep;// * GPT.GptimerMultiple;
+            } else {
+                instru.Vset -= cv->_Vstep;// * GPT.GptimerMultiple;
+            }
+
+            if (VmaxCounter && VminCounter) {
+                if (cv->_direction_up && cv->_current_direction_up) {
+                    if (instru.Vset >= cv->_Vinit) {
+                        cv->_cycleNumber--;
+                        VminCounter = false;
+                        VmaxCounter = false;
+                    }
+                }
+                if (!cv->_direction_up && !cv->_current_direction_up) {
+                    if (instru.Vset <= cv->_Vinit) {
+                        cv->_cycleNumber--;
+                        VminCounter = false;
+                        VmaxCounter = false;
+                    }
+                }
+            }
+
+            if (instru.Vset >= cv->_Vmax) {
+                cv->_current_direction_up = false;
+            } else if (instru.Vset <= cv->_Vmin) {
+                cv->_current_direction_up = true;
+            }
+
+            /*stop condition*/
+            if (cv->_cycleNumber == 0) {
+                PeriodicEvent = false;
+            }
+        }
+    }
+}
+
+static void CV_Plot(void)
+{
+    struct wm_cv_ctx_t *cv = (struct wm_cv_ctx_t *)wm_get();
+    static uint8_t ADC_cnt = 0;
+    void *wm = wm_get();
+
+    if (ADC_cnt == 0) {
+        LPTIA_change_gain();
+        ADC_cnt++;
+
+    } else if (ADC_cnt == 1) {
+        read_LPTIA_Iin();
+        ADC_cnt = 0;
+    }
+
+    return;
+}

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/mode_eis.h

@@ -0,0 +1,314 @@
+
+
+
+
+/***
+DC Volt            0 mv
+AC Amp             100 mv
+Freq               200000Hz~0.1Hz
+Points per decades 10 points
+Point spacing      Logarithm
+Delay              0 points
+Average            2
+Current range      Auto
+
+[CC2650] att_write 360CD10100CB7355000000070000
+[CC2650] att_write 360BD10261A801000004000A00
+***/
+
+#define DECODE_INS_1               0x01
+#define DECODE_INS_2               0x02
+#define DECODE_INS_MODE            0xFF
+
+static void decode_eis_mode(uint8_t *instruction)
+{
+    uint8_t *ins = instruction;
+    uint8_t ins_step = ins[3];
+
+
+    if (ins_step == DECODE_INS_1) {
+        instru.f1            = (uint32_t)ins[4] << 24 | (uint32_t)ins[5] << 16 | (uint32_t)ins[6] << 8 | (uint32_t)ins[7]; //FREQ_START //13333333
+        instru.f2            = (uint32_t)ins[8] << 24 | (uint32_t)ins[9] << 16 | (uint32_t)ins[10] << 8 | (uint32_t)ins[11]; //FREQ_STOP //7
+        //instru.sampleRate    = 15;//CalcDelayTime(User2Freq(instru.f1), true); //ms //read
+        instru.fmax          = (uint32_t)VMAX(instru.f1, instru.f2); //13333333
+        instru.fmin          = (uint32_t)VMIN(instru.f1, instru.f2); //7
+        instru.delay         = (uint16_t)ins[12] << 8 | (uint16_t)ins[13]; //DELAY/10 how many periods    //0
+        if (instru.f1 > instru.f2)
+            instru.directionInit = 0; //0:reverse   1:forward            //instru.directionInit = 0
+        else if (instru.f1 <= instru.f2)
+            instru.directionInit = 1;
+
+        return;
+    }
+
+    if (ins_step == DECODE_INS_2) {
+        instru.dcbias        = (uint16_t)ins[4] << 8 | (uint16_t)ins[5];  //25000
+        instru.acamp         = (uint16_t)ins[6] << 8 | (uint16_t)ins[7];  //256
+        instru.avgnum        = (uint8_t)ins[8];                           //0
+        instru.gain_lv_hstia = (uint8_t)ins[9];                           //4 = HSRTIA_200R
+        instru.ppd           = (uint16_t)ins[10] << 8 | (uint16_t)ins[11]; //10
+        instru.scale         = (uint8_t)ins[12];                           //0
+
+        return;
+    }
+
+    if (ins_step == DECODE_INS_MODE) {
+        instru.eliteFxn = CURVE_EIS;
+        set_hs_only();
+        if (instru.gain_lv_hstia < HSRTIA_MAX) {
+            instru.HSTIAAutoGainEnable = 0;
+            HSTIAGainCtrl(instru.gain_lv_hstia);
+        } else {
+            instru.HSTIAAutoGainEnable = 1;
+            instru.gain_lv_hstia = HSRTIA_200R;
+            HSTIAGainCtrl(instru.gain_lv_hstia);
+        }
+        HSDAC_outputV(instru.dcbias);
+        AD5940_SPIWriteReg(WGFCW, instru.fset);
+        AD5940_SPIWriteReg(WGCON, 0x0); // 0x0: DC disable ac first
+        AD5940_SPIWriteReg(WGAMPLITUDE, instru.acamp);
+        AD5940_SPIWriteReg(WGCON, 0x00000004); //0x4: Sinusoid
+        ModeLED(WORKING);
+
+        return;
+    }
+
+    return;
+}
+
+//////EIS PLOT RELATED FUNCTION START//////
+static uint8_t CalcDecade(uint32_t f1, uint32_t f2)
+{
+    uint8_t decades; //max is 7
+    decades = log10(f2/f1);
+    return decades;
+}
+
+static void eis_fscan(void)
+{
+    struct wm_eis_ctx_t *eis = (struct wm_eis_ctx_t *)wm_get();
+    static uint16_t LogSpacingTable10[10] = {1000, 1292, 1668, 2154, 2783, 3594, 4642, 5995, 7743, 10000};
+    static uint16_t LogSpacingTable9[9] = {1000, 1334, 1778, 2371, 3162, 4217, 5623, 7499, 10000};
+    static uint16_t LogSpacingTable8[8] = {1000, 1389, 1931, 2683, 3728, 5179, 7197, 10000};
+    static uint16_t LogSpacingTable7[7] = {1000, 1468, 2154, 3162, 4642, 6813, 10000};
+    static uint16_t LogSpacingTable6[6] = {1000, 1585, 2512, 3981, 6310, 10000};
+    static uint16_t LogSpacingTable5[5] = {1000, 1778, 3162, 5623, 10000};
+    static uint16_t LogSpacingTable4[4] = {1000, 2154, 4642, 10000};
+    static uint16_t LogSpacingTable3[3] = {1000, 3162, 10000};
+    static uint16_t LogSpacingTable2[2] = {1000, 10000};
+    static uint32_t TenPowerTable[9] = {1, 10, 100, 1000, 10000, 100000, 1000000, 10000000};
+
+    if (vscanReset) {
+        eis->_in_reset_flag = true;
+
+        eis->_f1 = User2Freq(eis->_f1);
+        eis->_f2 = User2Freq(eis->_f2);
+        eis->_fmax = User2Freq(eis->_fmax);
+        eis->_fmin = User2Freq(eis->_fmin);
+
+        if (instru.directionInit == 1) {
+            eis->_direction_up         = true;
+        } else if (instru.directionInit == 0) {
+            eis->_direction_up         = false;
+        }
+
+        eis->_decades = CalcDecade(instru.fmin, instru.fmax);
+
+        instru.fset = eis->_f1;
+
+        vscanReset = false;
+    }
+
+    if (!vscanReset) {
+        if(eis->_direction_up) {
+            if(eis->_sweepIndex == 0){
+                if(eis->_decadeIndex < eis->_decades) {
+                    eis->_fd1 = eis->_f1 * TenPowerTable[eis->_decadeIndex];
+                    eis->_fd2 = eis->_f1 * TenPowerTable[eis->_decadeIndex + 1];
+                } else if (eis->_decadeIndex == eis->_decades) {
+                    eis->_fd1 = eis->_fd2;//eis->_f1 * TenPowerTable[decadeIndex];
+                    eis->_fd2 = eis->_fmax;
+                }
+            }
+
+            if(eis->_decadeIndex != 0 && eis->_sweepIndex == 0){
+                eis->_sweepIndex++;
+            }
+
+            if(instru.scale == 0) { // logarithm
+                if (eis->_ppd == 10) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable10[eis->_sweepIndex] + 500)/ 1000;
+                }
+                else if (eis->_ppd == 9){
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable9[eis->_sweepIndex] + 500)/ 1000;
+                }
+                else if (eis->_ppd == 8) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable8[eis->_sweepIndex] + 500)/ 1000;
+                }
+                else if (eis->_ppd == 7) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable7[eis->_sweepIndex] + 500)/ 1000;
+                }
+                else if (eis->_ppd == 6) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable6[eis->_sweepIndex] + 500)/ 1000;
+                }
+                else if (eis->_ppd == 5) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable5[eis->_sweepIndex] + 500)/ 1000;
+                }
+                else if (eis->_ppd == 4) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable4[eis->_sweepIndex] + 500)/ 1000;
+                }
+                else if (eis->_ppd == 3) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable3[eis->_sweepIndex] + 500)/ 1000;
+                }
+                else if (eis->_ppd == 2) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable2[eis->_sweepIndex] + 500)/ 1000;
+                }
+            }
+            else if (instru.scale == 1) { // linear
+                instru.fset = eis->_fd1 + eis->_sweepIndex * ((eis->_fd2 - eis->_fd1) / (eis->_ppd - 1));
+            }
+
+            if(instru.fset > eis->_fmax){
+                instru.fset = eis->_fmax;
+            }
+
+        } else { //reverse
+            if(eis->_sweepIndex == 0){
+                if(eis->_decadeIndex < eis->_decades){
+                    eis->_fd1 = eis->_f1 / TenPowerTable[eis->_decadeIndex];
+                    eis->_fd2 = eis->_f1 / TenPowerTable[eis->_decadeIndex + 1];
+                } else if (eis->_decadeIndex == eis->_decades){
+                    eis->_fd1 = eis->_fd2; //eis->_f1 / TenPowerTable[eis->_decadeIndex];
+                    eis->_fd2 = eis->_fmin;
+                }
+            }
+
+            if(eis->_decadeIndex != 0 && eis->_sweepIndex == 0){
+                eis->_sweepIndex++;
+            }
+
+            if(instru.scale == 0) { // logarithm
+                if (eis->_ppd == 10) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable10[9 - eis->_sweepIndex] + 5000)/ 10000;
+                }
+                else if (eis->_ppd == 9) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable9[8 - eis->_sweepIndex] + 5000)/ 10000;
+                }
+                else if (eis->_ppd == 8) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable8[7 - eis->_sweepIndex] + 5000)/ 10000;
+                }
+                else if (eis->_ppd == 7) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable7[6 - eis->_sweepIndex] + 5000)/ 10000;
+                }
+                else if (eis->_ppd == 6) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable6[5 - eis->_sweepIndex] + 5000)/ 10000;
+                }
+                else if (eis->_ppd == 5) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable5[4 - eis->_sweepIndex] + 5000)/ 10000;
+                }
+                else if (eis->_ppd == 4) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable4[3 - eis->_sweepIndex] + 5000)/ 10000;
+                }
+                else if (eis->_ppd == 3) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable3[2 - eis->_sweepIndex] + 5000)/ 10000;
+                }
+                else if (eis->_ppd == 2) {
+                    instru.fset = ((uint64_t)eis->_fd1 * LogSpacingTable2[1 - eis->_sweepIndex] + 5000)/ 10000;
+                }
+            }
+            else if(instru.scale == 1) { // linear
+                instru.fset = eis->_fd1 - eis->_sweepIndex * ((eis->_fd1 - eis->_fd2) / (eis->_ppd - 1));
+            }
+
+            if(instru.fset < eis->_fmin){
+                instru.fset = eis->_fmin;
+            }
+        }
+        if (!gainChange_flag) {
+            if (++eis->_sweepIndex == eis->_ppd) {
+                eis->_sweepIndex = 0;
+                eis->_decadeIndex ++;
+            }
+        }
+    }
+
+
+    SetSamplingTime(instru.fset);
+
+    instru.sampleRate = 2000;
+}
+
+static void EIS_Plot(void) //real and imag impedance plot
+{
+    static uint8_t  avgNumTable[4] = {2, 4, 6, 8};
+    struct wm_eis_ctx_t *eis = (struct wm_eis_ctx_t *)wm_get();
+    static uint8_t ADC_cnt = 0;
+    static int32_t realSum, imagSum = 0;
+    int32_t avg_real, avg_imag = 0;
+    static uint8_t avg_count = 0;
+    void *wm = wm_get();
+
+    if (fout_flag){
+        SetWGAmp(instru.acamp,instru.fset);
+        DAC_outputF(Freq2DAC(instru.fset)); //[10mHz->Reg's]
+        EnDFTnADC(1);
+        instru.sampleRate = CalcDelayTime(instru.fset);
+        fout_flag = false;
+        if (eis->_in_reset_flag) {
+            avg_count = 0;
+            realSum = 0;
+            imagSum = 0;
+            ADC_cnt = 0;
+            eis->_in_reset_flag = false;
+        }
+    } else {
+        if (ADC_cnt == 0){
+            HSTIA_change_gain();            // ADC measure
+            if (gainChange_flag) {
+                gainChange_flag = false;
+                instru.sampleRate = CalcDelayTime(instru.fset);
+                instru.real = 0;
+                instru.imag = 0;
+                ADC_cnt = 0;
+            } else {
+                instru.sampleRate = 15;
+                ADC_cnt ++;
+            }
+        }
+        else if (ADC_cnt == 1) {
+            realSum += instru.real;
+            imagSum += instru.imag;
+            avg_count++;
+            instru.sampleRate = 15;
+            if (avg_count == avgNumTable[instru.avgnum]){
+                avg_real = realSum / avg_count;
+                avg_imag = imagSum / avg_count;
+
+                InputNotify(NOTIFY_CURRENT, avg_imag);
+                InputNotify(NOTIFY_VOLT, avg_real);
+                InputNotify(NOTIFY_IMPEDANCE, instru.fset);
+                NotifyCh4 = (uint32_t)eis->_amp * 1000 * 800 / 2047; //[uV]
+
+                if(eis->_direction_up){
+                    if (instru.fset >= eis->_fmax) {
+                        PeriodicEvent = false;
+                        finishMode = 1;
+                    }
+                } else {
+                    if (instru.fset <= eis->_fmin) {
+                        PeriodicEvent = false;
+                        finishMode = 1;
+                    }
+                } 
+                EnDFTnADC(0);
+                avg_count = 0;
+                realSum = 0;
+                imagSum = 0;
+                notify_flag = true;
+            }
+            ADC_cnt = 0;
+        }
+    }
+
+    return;
+}

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/mode_rt.h

@@ -0,0 +1,78 @@
+static void decode_rt_mode(uint8 *ins)
+{
+    instru.eliteFxn    = CURVE_RT;
+    instru.notifyRate  = (uint32_t)ins[7] << 8 | (uint32_t)ins[8];
+    instru.notifyRate  = 10000 / instru.notifyRate * 10;
+    // instru.notifyRate  = 100;
+    // instru.measure_vin_range = ins[7];
+    // instru.measure_vin_range = 0;
+    setEIS_CV();
+    instru.Vinit = (uint32_t)ins[3] << 8 | (uint32_t)ins[4];
+
+    ModeLED(WORKING);
+
+    return;
+}
+
+static void CalcuResistance(int32_t Iin)
+{
+    /* Elite 100000 = 100R
+       Elite 1000000 = 1KR
+       Elite 10000000 = 10KR
+       Elite 100000000 = 100KR
+       Elite 1000000000 = 1MR
+     */
+
+    struct wm_rt_ctx_t *rt = (struct wm_rt_ctx_t *)wm_get();
+    int64_t resist;
+    int64_t volt = instru.Vset / 200; // [uV]
+    int64_t current = Iin;
+
+    resist = volt * 1000000 / current; //R = V / Iin; [mOhm]
+    InputNotify(NOTIFY_IMPEDANCE, resist);
+}
+
+static void RT_Plot(void)
+{
+    struct wm_rt_ctx_t *rt = (struct wm_rt_ctx_t *)wm_get();
+    static uint8_t ADC_cnt = 0;
+    void *wm = wm_get();
+
+    if (ADC_cnt == 0) {
+        LPTIA_change_gain();
+        ADC_cnt++;
+
+    } else if (ADC_cnt == 1) {
+        int32_t Iin = read_LPTIA_Iin();
+        CalcuResistance(Iin);
+        ADC_cnt = 0;
+    }
+
+    return;
+}
+
+static void rt_vscan(void)
+{
+    struct wm_rt_ctx_t *rt = (struct wm_rt_ctx_t *)wm_get();
+
+    if(vscanReset){
+        instru.Vset = rt->_Vinit;
+    }
+
+    if(!vscanReset){
+        instru.Vset = rt->_Vinit;
+    }
+
+    return;
+}
+
+static void set_rt_volt(int32_t volt)
+{
+    struct wm_rt_ctx_t *rt = (struct wm_rt_ctx_t *)wm_get();
+
+    volt = (volt - 25000) * 4 * 4000;
+    
+    rt->_Vinit = volt;
+
+    return;
+}

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/mode_vt.h

@@ -0,0 +1,47 @@
+
+
+static void decode_vt_mode(uint8 *ins)
+{
+    instru.eliteFxn    = CURVE_VT;
+    instru.notifyRate  = (uint32_t)ins[5] << 8 | (uint32_t)ins[6];
+    instru.notifyRate  = 10000 / instru.notifyRate * 10;
+    instru.measure_vin_range = ins[7];
+    setEIS_CV();
+    AD5940_SPIWriteReg(ADCCON, 0x0001080E); //PGA = 1.5    //VT
+    uint8_t z;
+    uint16_t b;
+    if (instru.measure_vin_range == 0) { //measure +volt
+        z = 0;
+        b = 0;
+    } else if (instru.measure_vin_range == 1) { //measure +-1V
+        z = 32;
+        b = 2048;
+    } else if (instru.measure_vin_range == 2) { //measure -volt
+        z = 62;
+        b = 3910;
+    }
+    set_lpdac_ce_1100mv(z, b);
+    disconnect_rtia();
+    ModeLED(WORKING);
+
+    return;
+}
+
+static void VT_Plot(void)
+{
+    struct wm_ca_ctx_t *ca = (struct wm_ca_ctx_t *)wm_get();
+    static uint8_t ADC_cnt = 0;
+    void *wm = wm_get();
+
+    if (ADC_cnt == 0) {
+        // LPTIA_change_gain();
+        ADC_cnt++;
+
+    } else if (ADC_cnt == 1) {
+        read_LPTIA_Vin();
+        ADC_cnt = 0;
+    }
+
+    return;
+}
+

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/scan_volt.h

@@ -1,879 +0,0 @@
-#ifndef SCAN_VOLT_H
-#define SCAN_VOLT_H
-
-#ifdef  __cplusplus
-extern "C" {
-#endif
-
-#define Vset instru.Vset
-
-static void iv_vscan(void)
-{
-    struct wm_iv_ctx_t *iv = (struct wm_iv_ctx_t *)wm_get();
-
-    if (vscanReset) {
-        if (instru.directionInit == 1) {
-            iv->_direction_up         = true;
-            iv->_current_direction_up = true;
-        } else if (instru.directionInit == 0) {
-            iv->_direction_up         = false;
-            iv->_current_direction_up = false;
-        }
-
-        //Vsetp = x * 20 * N, x=xmV ; N=VscanRate
-        if (instru.step <= 10) {
-            iv->_Vstep = instru.step * instru.VsetRate / 5;
-        } else {
-            iv->_Vstep = instru.step / 5 * instru.VsetRate;
-        }
-
-        Vset = iv->_Vinit;
-    }
-
-    if (!vscanReset) {
-        if (iv->_current_direction_up) {
-            if (Vset >= iv->_Vmax) {
-                PeriodicEvent = false;
-            }
-        } else {
-            if (Vset <= iv->_Vmin) {
-                PeriodicEvent = false;
-            }
-        }
-
-        if (iv->_current_direction_up) {
-            Vset = Vset + iv->_Vstep * GPT.GptimerMultiple;
-        } else {
-            Vset = Vset - iv->_Vstep * GPT.GptimerMultiple;
-        }
-    }
-
-    return;
-}
-
-static void iv_cy_vscan(void)
-{
-    struct wm_iv_cy_ctx_t *iv_cy = (struct wm_iv_cy_ctx_t *)wm_get();
-    static bool VminCounter;
-    static bool VmaxCounter;
-
-    NotifyCycleNumber = (instru.cycleNumber - iv_cy->_cycleNumber + 1);
-
-    if(vscanReset){
-        VmaxCounter = false;
-        VminCounter = false;
-
-        if(instru.directionInit == 1){
-            iv_cy->_direction_up         = true;
-            iv_cy->_current_direction_up = true;
-        }else if(instru.directionInit == 0){
-            iv_cy->_direction_up         = false;
-            iv_cy->_current_direction_up = false;
-        }
-
-        //Vsetp = x * 20 * N, x=xmV ; N=VscanRate
-        if(instru.step <= 10){
-            iv_cy->_Vstep = instru.step * instru.VsetRate / 5;
-        }else{
-            iv_cy->_Vstep = instru.step / 5 * instru.VsetRate;
-        }
-
-        if(iv_cy->_Vmin == iv_cy->_Vinit){
-            VminCounter = true;
-        }
-        if(iv_cy->_Vmax == iv_cy->_Vinit){
-            VmaxCounter = true;
-        }
-
-        Vset = iv_cy->_Vinit;
-    }
-
-    if(!vscanReset){
-        if (Vset >= iv_cy->_Vmax){
-            VmaxCounter = true;
-        }else if (Vset <= iv_cy->_Vmin){
-            VminCounter = true;
-        }
-
-        if (iv_cy->_current_direction_up){
-            Vset = Vset + iv_cy->_Vstep * GPT.GptimerMultiple;
-        }else{
-            Vset = Vset - iv_cy->_Vstep * GPT.GptimerMultiple;
-        }
-
-        if(VmaxCounter && VminCounter){
-            if(iv_cy->_direction_up && iv_cy->_current_direction_up){
-                if(Vset >= iv_cy->_Vinit){
-                    iv_cy->_cycleNumber--;
-                    VminCounter = false;
-                    VmaxCounter = false;
-                }
-            }
-            if(!iv_cy->_direction_up && !iv_cy->_current_direction_up){
-                if(Vset <= iv_cy->_Vinit){
-                    iv_cy->_cycleNumber--;
-                    VminCounter = false;
-                    VmaxCounter = false;
-                }
-            }
-        }
-
-        if (Vset >= iv_cy->_Vmax){
-            iv_cy->_current_direction_up = false;
-        }else if (Vset <= iv_cy->_Vmin){
-            iv_cy->_current_direction_up = true;
-        }
-
-        /*stop condition*/
-        if(iv_cy->_cycleNumber == 0){
-            PeriodicEvent = false;
-        }
-    }
-
-    return;
-}
-
-static void it_vscan(void)
-{
-    struct wm_it_ctx_t *it = (struct wm_it_ctx_t *)wm_get();
-
-    if (vscanReset) {
-        Vset = it->_Vinit;
-    }
-
-    if(!vscanReset) {
-        Vset = it->_Vinit;
-    }
-
-    return;
-}
-
-static void rt_vscan(void)
-{
-    struct wm_rt_ctx_t *rt = (struct wm_rt_ctx_t *)wm_get();
-
-    if (vscanReset) {
-        Vset = rt->_Vinit;
-    }
-
-    if(!vscanReset) {
-        Vset = rt->_Vinit;
-    }
-
-    return;
-}
-
-static void vo_vscan(void)
-{
-    struct wm_vo_ctx_t *vo = (struct wm_vo_ctx_t *)wm_get();
-
-    if (vscanReset) {
-        Vset = vo->_Vinit;
-    }
-
-    if(!vscanReset) {
-        Vset = vo->_Vinit;
-    }
-
-    return;
-}
-
-#define DELTAVOLTMAX 2000000 //2000000 = 10mV
-static void cc_vscan(void)
-{
-    /* Transform setting CC into IUC
-     *
-     * User code in CC mode : 0 ~ 3000000
-     * Real current value : -15.00000 ~ 15.00000 mA
-     *  => user code = 1500000 mapping to 0.00000 mA
-     */
-
-    struct wm_cc_ctx_t *cc = (struct wm_cc_ctx_t *)wm_get();
-    struct wm_meas_t *m = &cc->measure;
-    uint16_t divisionRate;
-    int32_t deltaI;
-    int32_t deltaV;
-    int32_t Iin;
-    int32_t Vin;
-
-    if (vscanReset) {
-        Vset = 0;
-
-        if (cc->_charge == 0) {
-            cc->_Iset = instru.constantCurrent * 200 * (-1);
-            //[50pA] //controller UI 15000uA => Elite 1500000 => 1500000 * 10 * 1000 / 50 [50pA];
-        }
-
-        Iin = m->_measureCurrent * 20; //[50pA]   nA => 50pA
-        Vin = m->_measureVin * 200; //[5nV]
-
-        Vset = Vin + cc->_Iset; //[5nV]
-
-        if (Vset >= 1100000000) { // 5.5V
-            Vset = 1100000000;
-        } else if (Vset <= -1000000000) { //-5V
-            Vset = -1000000000;
-        }
-    }
-
-    if (!vscanReset) {
-        Iin = m->_measureCurrent * 20; //[50pA]   nA => 50pA
-        deltaI = Iin - cc->_Iset;
-
-        if (deltaI > 2000000 || deltaI < -2000000) { //100uA
-            divisionRate = 1;
-        } else {
-            divisionRate = 20;
-        }
-
-        deltaV = -1 * (deltaI / divisionRate); //-5 * deltaI / 5000   //pV=> 5nV
-
-        if (deltaV > DELTAVOLTMAX) { //2000000 = 10mV
-            deltaV = DELTAVOLTMAX;
-        } else if (deltaV < (-DELTAVOLTMAX)) {
-            deltaV = (-DELTAVOLTMAX);
-        }
-
-        Vset = Vset + deltaV; //[5nV]
-
-        if (Vset >= 1100000000) { // 5.5V
-            Vset = 1100000000;
-        } else if (Vset <= -1000000000) { //-5V
-            Vset = -1000000000;
-        }
-
-        if (Vset <= cc->_Vmin) {
-            Vset = cc->_Vmin;
-        } else if (Vset >= cc->_Vmax) {
-            Vset = cc->_Vmax;
-        }
-    }
-
-    return;
-}
-
-static void cv_vscan(void)
-{
-    struct wm_cv_ctx_t *cv = (struct wm_cv_ctx_t *)wm_get();
-    static bool VminCounter;
-    static bool VmaxCounter;
-
-    NotifyCycleNumber = (instru.cycleNumber - cv->_cycleNumber + 1);
-
-
-    if (vscanReset) {
-        VmaxCounter = false;
-        VminCounter = false;
-
-        if (instru.directionInit == 1) {
-            cv->_direction_up         = true;
-            cv->_current_direction_up = true;
-        } else {
-            cv->_direction_up         = false;
-            cv->_current_direction_up = false;
-        }
-
-        //Vsetp = x * 20 * N, x=xmV ; N=VscanRate
-        if (instru.step <= 10) {
-            cv->_Vstep = instru.step *  instru.VsetRate / 5;
-        } else {
-            cv->_Vstep = instru.step / 5 *  instru.VsetRate;
-        }
-
-        if (cv->_Vmin == cv->_Vinit) {
-            VminCounter = true;
-        }
-        if (cv->_Vmax == cv->_Vinit) {
-            VmaxCounter = true;
-        }
-
-        Vset = cv->_Vinit;
-    }
-
-    if (!vscanReset) {
-        if ((instru.Vinit < instru.Ve1 && instru.Vinit < instru.Ve2) ||
-        (instru.Vinit > instru.Ve1 && instru.Vinit > instru.Ve2)
-        ) {
-            if (cv->_current_direction_up) {
-                Vset = Vset + cv->_Vstep * GPT.GptimerMultiple;
-            } else {
-                Vset = Vset - cv->_Vstep * GPT.GptimerMultiple;
-            }
-
-            if (instru.Vinit < instru.Ve1 && instru.Vinit < instru.Ve2) {
-                if (Vset == cv->_Vmin) {
-                    VminCounter = true;
-                    instru.Vinit = instru.Vmin;
-                    cv->_Vinit = cv->_Vmin;
-                }
-            } else if (instru.Vinit > instru.Ve1 && instru.Vinit > instru.Ve2) {
-                if (Vset == cv->_Vmax) {
-                    VmaxCounter = true;
-                    instru.Vinit = instru.Vmax;
-                    cv->_Vinit = cv->_Vmax;
-                }
-            }
-        } else {
-            if (Vset >= cv->_Vmax) {
-                VmaxCounter = true;
-            } else if (Vset <= cv->_Vmin) {
-                VminCounter = true;
-            }
-
-            if (cv->_current_direction_up) {
-                Vset = Vset + cv->_Vstep * GPT.GptimerMultiple;
-            } else {
-                Vset = Vset - cv->_Vstep * GPT.GptimerMultiple;
-            }
-
-            if (VmaxCounter && VminCounter) {
-                if (cv->_direction_up && cv->_current_direction_up) {
-                    if (Vset >= cv->_Vinit) {
-                        cv->_cycleNumber--;
-                        VminCounter = false;
-                        VmaxCounter = false;
-                    }
-                }
-                if (!cv->_direction_up && !cv->_current_direction_up) {
-                    if (Vset <= cv->_Vinit) {
-                        cv->_cycleNumber--;
-                        VminCounter = false;
-                        VmaxCounter = false;
-                    }
-                }
-            }
-
-            if (Vset >= cv->_Vmax) {
-                cv->_current_direction_up = false;
-            } else if (Vset <= cv->_Vmin) {
-                cv->_current_direction_up = true;
-            }
-
-            /*stop condition*/
-            if (cv->_cycleNumber == 0) {
-                PeriodicEvent = false;
-            }
-        }
-    }
-
-    return;
-}
-
-static void lsv_vscan(void)
-{
-    struct wm_lsv_ctx_t *lsv = (struct wm_lsv_ctx_t *)wm_get();
-
-    NotifyCycleNumber = (instru.cycleNumber - lsv->_cycleNumber + 1);
-
-    if (vscanReset) {
-        if (instru.directionInit == 1) {
-            lsv->_direction_up         = true;
-            lsv->_current_direction_up = true;
-        } else {
-            lsv->_direction_up         = false;
-            lsv->_current_direction_up = false;
-        }
-
-         //Vsetp = x * 20 * N, x=xmV ; N=VscanRate
-        if (instru.step <= 10) {
-            lsv->_Vstep = instru.step *  instru.VsetRate / 5;
-        } else {
-            lsv->_Vstep = instru.step / 5 *  instru.VsetRate;
-        }
-
-        Vset = lsv->_Vinit;
-    }
-
-    if (!vscanReset) {
-
-        if (lsv->_current_direction_up) {
-            Vset = Vset + lsv->_Vstep * GPT.GptimerMultiple;
-        } else {
-            Vset = Vset - lsv->_Vstep * GPT.GptimerMultiple;
-        }
-
-        /*stop condition*/
-        if (Vset >= lsv->_Vmax) {
-            PeriodicEvent = false;
-        } else if (Vset <= lsv->_Vmin) {
-            PeriodicEvent = false;
-        }
-    }
-
-    return;
-}
-
-static void ca_vscan(void)
-{
-    struct wm_ca_ctx_t *ca = (struct wm_ca_ctx_t *)wm_get();
-
-    if(vscanReset){
-        Vset = ca->_Vinit;
-    }
-
-    if(!vscanReset){
-        Vset = ca->_Vinit;
-    }
-
-    return;
-}
-
-
-static void uni_pulse_vscan(uint32_t time)
-{
-    uint32_t t = time;
-    struct wm_uni_pulse_ctx_t *p = (struct wm_uni_pulse_ctx_t *)wm_get();
-    uint32_t m;
-    uint32_t t_min;
-    uint32_t t_max;
-
-    if(vscanReset){
-        Vset = p->_v0;
-
-        return;
-    }
-
-    if(!vscanReset){
-
-        if (t == 0) {
-            m = 0;
-        } else {
-           m = t % p->_t_period;
-        }
-
-        if (m < p->_t_pa[0]) {
-            p->_Vset = p->_v_initial[0] + p->_v_slope[0] * t + p->_v_step[0] * (int32_t)(t / p->_t_period);
-            Vset = p->_Vset;
-
-            t_min = p->_t_pulse_min[0];
-            t_max = p->_t_pulse_max[0];
-
-            if (m > t_min && m < t_max) {
-                calc_avg_en = true;
-            } else {
-                calc_avg_en = false;
-            }
-
-            return;
-        }
-
-        if (m < p->_t_pa[1]) {
-            p->_Vset = p->_v_initial[1] + p->_v_slope[1] * t + p->_v_step[1] * (int32_t)(t / p->_t_period);
-            Vset = p->_Vset;
-
-            t_min = p->_t_pa[0] + p->_t_pulse_min[1];
-            t_max = p->_t_pa[0] + p->_t_pulse_max[1];
-
-            if (m > t_min && m < t_max) {
-                calc_avg_en = true;
-            } else {
-                calc_avg_en = false;
-            }
-
-            return;
-        }
-
-        if (m < p->_t_pa[2]) {
-            p->_Vset = p->_v_initial[2] + p->_v_slope[2] * t + p->_v_step[2] * (int32_t)(t / p->_t_period);
-            Vset = p->_Vset;
-
-            t_min = p->_t_pa[1] + p->_t_pulse_min[2];
-            t_max = p->_t_pa[1] + p->_t_pulse_max[2];
-
-            if (m > t_min && m < t_max) {
-                calc_avg_en = true;
-            } else {
-                calc_avg_en = false;
-            }
-
-            return;
-        }
-
-        if (m < p->_t_pa[3]) {
-            p->_Vset = p->_v_initial[3] + p->_v_slope[3] * t + p->_v_step[3] * (int32_t)(t / p->_t_period);
-            Vset = p->_Vset;
-
-            t_min = p->_t_pa[2] + p->_t_pulse_min[3];
-            t_max = p->_t_pa[2] + p->_t_pulse_max[3];
-
-            if (m > t_min && m < t_max) {
-                calc_avg_en = true;
-            } else {
-                calc_avg_en = false;
-            }
-
-            return;
-        }
-
-        return;
-    }
-
-    return;
-}
-
-static void dpv_vscan(uint32_t time)
-{
-    uint32_t t = time;
-    struct wm_dpv_ctx_t *p = (struct wm_dpv_ctx_t *)wm_get();
-    uint32_t m;
-    uint32_t t_min;
-    uint32_t t_max;
-
-    if(vscanReset){
-        Vset = p->_v0;
-
-        return;
-    }
-
-    if(!vscanReset){
-
-        if (t == 0) {
-            m = 0;
-        } else {
-           m = t % p->_t_period;
-        }
-
-        if (m < p->_t_pa[0]) {
-            p->_Vset = p->_v_initial[0] + p->_v_slope[0] * t / 1000 + p->_v_step[0] * (int32_t)dpv_step_cnt; // _v_slope/100 = slope
-            Vset = p->_Vset;
-
-            t_min = p->_t_pulse_min[0];
-            t_max = p->_t_pulse_max[0];
-
-            if (m > t_min && m < t_max) {
-                calc_avg_en = true;
-            } else {
-                calc_avg_en = false;
-            }
-
-            if ((p->_v_curr_direc && Vset >= p->_v_stop) ||
-               (!p->_v_curr_direc && Vset <= p->_v_stop)) {
-                PeriodicEvent = false;
-            }
-
-            return;
-        }
-
-        if (m < p->_t_pa[1]) {
-            p->_Vset = p->_v_initial[1] + p->_v_slope[1] * t / 1000 + p->_v_step[1] * (int32_t)dpv_step_cnt;
-            Vset = p->_Vset;
-
-            t_min = p->_t_pa[0] + p->_t_pulse_min[1];
-            t_max = p->_t_pa[0] + p->_t_pulse_max[1];
-
-            if (m > t_min && m < t_max) {
-                calc_avg_en = true;
-            } else {
-                calc_avg_en = false;
-            }
-
-            return;
-        }
-
-        return;
-    }
-
-    return;
-}
-
-static void dpv_advance_vscan(uint32_t time)
-{
-    uint32_t t = time;
-    struct wm_dpv_advance_ctx_t *p = (struct wm_dpv_advance_ctx_t *)wm_get();
-    uint32_t m;
-    uint32_t t_min;
-    uint32_t t_max;
-    static bool VminCounter;
-    static bool VmaxCounter;
-
-    if(vscanReset){
-        if (p->_v_direc_init) {
-            if (p->_v0 <= p->_v_up && p->_v0 <= p->_v_low && p->_v_2 > p->_v_1) {
-                VminCounter = true;
-            }
-
-        } else {
-            if (p->_v0 >= p->_v_up && p->_v0 >= p->_v_low && p->_v_1 > p->_v_2) {
-                VmaxCounter = true;
-            }
-        }
-
-
-
-        p->_Vset = p->_v0;
-        Vset = p->_Vset;
-
-        return;
-    }
-
-    if(!vscanReset){
-
-        if (t == 0) {
-            m = 0;
-        } else {
-           m = t % p->_t_period;
-        }
-
-        if (m < p->_t_pa[0]) {
-
-            t_min = p->_t_pulse_min[0];
-            t_max = p->_t_pulse_max[0];
-
-            if (m > t_min && m < t_max) {
-                calc_avg_en = true;
-            } else {
-                calc_avg_en = false;
-            }
-
-            p->_Vset = p->_v_initial[0] + p->_v_slope[0] * t / 1000 + p->_v_step[0] * (int32_t)dpv_step_cnt; // _v_slope/100 = slope
-            Vset = p->_Vset;
-
-            if (VminCounter == true && VmaxCounter == true) {
-                p->_cycleNumber--;
-                VminCounter = false;
-                VmaxCounter = false;
-
-            }
-
-            if (p->_cycleNumber <= 0) {
-                if (p->_v_stop_direction == true && p->_Vset >= p->_v_stop - p->_v_amp + p->_v_step[0]) {
-                    PeriodicEvent = false;
-                } else if (p->_v_stop_direction == false && p->_Vset <= p->_v_stop - p->_v_amp + p->_v_step[0]) {
-                    PeriodicEvent = false;
-                }
-            }
-
-            if (p->_v_curr_direc && p->_Vset >= p->_v_up - p->_v_amp + p->_v_step[0]) {
-                if (p->_v_invert_option) {
-                    p->_v_amp = p->_v_amp * (-1);
-                }
-                p->_v_initial[0] = p->_Vset;
-                p->_v_initial[1] = p->_v_initial[0] + p->_v_amp;
-                dpv_step_cnt = 0;
-                p->_v_step[0] = (-1) * p->_v_step[0];
-                p->_v_step[1] = (-1) * p->_v_step[1];
-                p->_v_curr_direc = false;
-                VmaxCounter = true;
-                p->_Vset = p->_v_initial[0] + p->_v_slope[0] * t / 1000 * (int32_t)dpv_step_cnt; // _v_slope/100 = slope
-                Vset = p->_Vset;
-
-            } else if (!p->_v_curr_direc && p->_Vset <= p->_v_low - p->_v_amp + p->_v_step[0]) {
-                if (p->_v_invert_option) {
-                    p->_v_amp = p->_v_amp * (-1);
-                }
-                p->_v_initial[0] = p->_Vset;
-                p->_v_initial[1] = p->_v_initial[0] + p->_v_amp;
-                dpv_step_cnt = 0;
-                p->_v_step[0] = (-1) * p->_v_step[0];
-                p->_v_step[1] = (-1) * p->_v_step[1];
-                p->_v_curr_direc = true;
-                VminCounter = true;
-                p->_Vset = p->_v_initial[0] + p->_v_slope[0] * t / 1000 * (int32_t)dpv_step_cnt; // _v_slope/100 = slope
-                Vset = p->_Vset;
-
-            }
-
-            return;
-        }
-
-        if (m < p->_t_pa[1]) {
-            p->_Vset = p->_v_initial[1] + p->_v_slope[1] * t / 1000 + p->_v_step[1] * (int32_t)dpv_step_cnt;
-            Vset = p->_Vset;
-
-            t_min = p->_t_pa[0] + p->_t_pulse_min[1];
-            t_max = p->_t_pa[0] + p->_t_pulse_max[1];
-
-            if (m > t_min && m < t_max) {
-                calc_avg_en = true;
-            } else {
-                calc_avg_en = false;
-            }
-
-            return;
-        }
-
-        return;
-    }
-
-    return;
-}
-
-static void pulse_vscan(void)
-{
-    struct wm_pulse_ctx_t *pulse = (struct wm_pulse_ctx_t *)wm_get();
-    static uint16_t lastVolt;
-
-    if (stiFirstTime) {
-        stiFirstTime = false;
-        lastVolt = 25000;
-        pulse->_sti_t_flag = 1;
-        pulse->_sti_v = pulse->_sti_v1;
-        pulse->_sti_t = pulse->_sti_t1;
-        if (pulse->_sti_t == 1) {
-            pulse->_sti_v = lastVolt;
-        }
-    } else if(!stiFirstTime) {
-        if (GPT.StiCounter >= pulse->_sti_t) {
-            GPT.StiCounter -= pulse->_sti_t; //to get right time
-
-            if (pulse->_sti_lp > 0) {
-                if (pulse->_sti_cy > 0) {
-                    if (pulse->_sti_t_flag == 1) {
-                        pulse->_sti_t_flag = 2;
-                        pulse->_sti_v = pulse->_sti_v2;
-                        pulse->_sti_t = pulse->_sti_t2;
-                        if (pulse->_sti_t == 1) {
-                            pulse->_sti_v = lastVolt;
-                        }
-                    } else if (pulse->_sti_t_flag == 2) {
-                        pulse->_sti_t_flag = 3;
-                        pulse->_sti_v = pulse->_sti_v3;
-                        pulse->_sti_t = pulse->_sti_t3;
-                        if (pulse->_sti_t == 1) {
-                            pulse->_sti_v = lastVolt;
-                        }
-                    } else if (pulse->_sti_t_flag == 3) {
-                        pulse->_sti_cy -- ;
-                        if (pulse->_sti_cy == 0) {
-                            pulse->_sti_t_flag = 4;
-                            pulse->_sti_v = pulse->_sti_v4;
-                            pulse->_sti_t = pulse->_sti_t4;
-                            if (pulse->_sti_t == 1) {
-                                pulse->_sti_v = lastVolt;
-                            }
-                        } else {
-                            pulse->_sti_t_flag = 2;
-                            pulse->_sti_v = pulse->_sti_v2;
-                            pulse->_sti_t = pulse->_sti_t2;
-                            if (pulse->_sti_t == 1) {
-                                pulse->_sti_v = lastVolt;
-                            }
-                        }
-                    }
-                } else if (pulse->_sti_cy <= 0){
-                    if (pulse->_sti_t_flag == 4) {
-                        pulse->_sti_lp -- ;
-                        if (pulse->_sti_lp > 0) {
-                            pulse->_sti_cy = instru.sti_cy;
-                            pulse->_sti_t_flag = 2;
-                            pulse->_sti_v = pulse->_sti_v2;
-                            pulse->_sti_t = pulse->_sti_t2;
-                            if (pulse->_sti_t == 1) {
-                                pulse->_sti_v = lastVolt;
-                            }
-                        } else {
-                            pulse->_sti_t_flag = 5;
-                            pulse->_sti_v = pulse->_sti_v5;
-                            pulse->_sti_t = pulse->_sti_t5;
-                            if (pulse->_sti_t == 1) {
-                                pulse->_sti_v = lastVolt;
-                            }
-                        }
-                    }
-                }
-            } else if (pulse->_sti_lp <= 0) {
-                if (pulse->_sti_t_flag == 5) {
-                    pulse->_sti_t_flag = 6;
-                    pulse->_sti_v = pulse->_sti_v6;
-                    pulse->_sti_t = pulse->_sti_t6;
-                    if (pulse->_sti_t == 1) {
-                        pulse->_sti_v = lastVolt;
-                    }
-                } else if (pulse->_sti_t_flag == 6) {
-                    pulse->_sti_t_flag = 7;
-                    pulse->_sti_v = pulse->_sti_v7;
-                    pulse->_sti_t = pulse->_sti_t7;
-                    if (pulse->_sti_t == 1) {
-                        pulse->_sti_v = lastVolt;
-                    }
-                } else if (pulse->_sti_t_flag == 7) {
-                    pulse->_sti_v = 25000;
-                    PeriodicEvent  = false;
-                    PIN15_setOutputValue(HIGH_Z_MODE, 0); // 0: open highz;
-                    ModeLED(NO_EVENT);
-                }
-            }
-        }
-    }
-
-    if (lastVolt != pulse->_sti_v) {
-        lastVolt = pulse->_sti_v;
-        //if (pulse->_sti_v == 25000) {
-        //    PIN15_setOutputValue(HIGH_Z_MODE, 0);   // 1 => close high_z mode
-        //} else {
-        //    PIN15_setOutputValue(HIGH_Z_MODE, 1);   // 1 => close high_z mode
-        //}
-        DAC_outputV(Usercode_Correction_to_DAC(VOUT_GAIN_240K, pulse->_sti_v));
-        DAC_outputV(Usercode_Correction_to_DAC(VOUT_GAIN_240K, pulse->_sti_v));
-    }
-
-    return;
-}
-
-static void chg_vo_para(uint16_t parameter, int32_t value)
-{
-    uint16_t pa = parameter;
-    int32_t val = value;
-    struct wm_vo_ctx_t *vo = (struct wm_vo_ctx_t *)wm_get();
-
-    if (pa == DAC_VOLT) {
-        vo->_Vinit = val;
-    }
-
-    return;
-}
-
-static void chg_it_para(uint16_t parameter, int32_t value)
-{
-    uint16_t pa = parameter;
-    int32_t val = value;
-    struct wm_it_ctx_t *it = (struct wm_it_ctx_t *)wm_get();
-
-    if (pa == DAC_VOLT) {
-        it->_Vinit = val;
-    }
-
-    return;
-}
-
-static void chg_rt_para(uint16_t parameter, int32_t value)
-{
-    uint16_t pa = parameter;
-    int32_t val = value;
-    struct wm_rt_ctx_t *rt = (struct wm_rt_ctx_t *)wm_get();
-
-    if (pa == DAC_VOLT) {
-        rt->_Vinit = val;
-    }
-
-    return;
-}
-
-static void set_para(uint8_t eliteFxn, uint16_t parameter, int32_t value)
-{
-    uint8_t mode = eliteFxn;
-    uint16_t pa = parameter;
-    int32_t val = value;
-
-    if (mode == CURVE_VO) {
-        chg_vo_para(pa, val);
-
-        return;
-    }
-
-    if (mode == CURVE_IT) {
-        chg_it_para(pa, val);
-
-        return;
-    }
-
-    if (mode == CURVE_RT) {
-        chg_rt_para(pa, val);
-
-        return;
-    }
-
-    return;
-}
-
-#endif

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/main.c

@@ -50,13 +50,9 @@
 
 #include <xdc/runtime/Error.h>
 
-
 #include <ti/drivers/Power.h>
 #include <ti/drivers/power/PowerCC26XX.h>
 #include <ti/sysbios/BIOS.h>
-#include <ti/drivers/SPI.h>
-#include <ti/drivers/spi/SPICC26XXDMA.h>
-#include <ti/drivers/dma/UDMACC26XX.h>
 
 #include "icall.h"
 #include "hal_assert.h"
@@ -136,7 +132,7 @@ PIN_Handle radCtrlHandle;
 
 extern void AssertHandler(uint8 assertCause, uint8 assertSubcause);
 
-//extern Display_Handle dispHandle;
+// extern Display_Handle dispHandle;
 
 /*******************************************************************************
  * @fn          Main
@@ -251,48 +247,49 @@ int main()
  */
 void AssertHandler(uint8 assertCause, uint8 assertSubcause)
 {
+/*
   // Open the display if the app has not already done so
-//  if ( !dispHandle )
-//  {
-//    dispHandle = Display_open(Display_Type_LCD, NULL);
-//  }
+  if ( !dispHandle )
+  {
+    dispHandle = Display_open(Display_Type_LCD, NULL);
+  }
 
-
-//  Display_print0(dispHandle, 0, 0, ">>>STACK ASSERT");
+  Display_print0(dispHandle, 0, 0, ">>>STACK ASSERT");
 
   // check the assert cause
-//  switch (assertCause)
-//  {
-//    case HAL_ASSERT_CAUSE_OUT_OF_MEMORY:
-//      Display_print0(dispHandle, 0, 0, "***ERROR***");
-//      Display_print0(dispHandle, 2, 0, ">> OUT OF MEMORY!");
-//      break;
-//
-//    case HAL_ASSERT_CAUSE_INTERNAL_ERROR:
-//      // check the subcause
-//      if (assertSubcause == HAL_ASSERT_SUBCAUSE_FW_INERNAL_ERROR)
-//      {
-//        Display_print0(dispHandle, 0, 0, "***ERROR***");
-//        Display_print0(dispHandle, 2, 0, ">> INTERNAL FW ERROR!");
-//      }
-//      else
-//      {
-//        Display_print0(dispHandle, 0, 0, "***ERROR***");
-//        Display_print0(dispHandle, 2, 0, ">> INTERNAL ERROR!");
-//      }
-//      break;
-//
-//    case HAL_ASSERT_CAUSE_ICALL_ABORT:
-//      Display_print0(dispHandle, 0, 0, "***ERROR***");
-//      Display_print0(dispHandle, 2, 0, ">> ICALL ABORT!");
-//      HAL_ASSERT_SPINLOCK;
-//      break;
-//
-//    default:
-//      Display_print0(dispHandle, 0, 0, "***ERROR***");
-//      Display_print0(dispHandle, 2, 0, ">> DEFAULT SPINLOCK!");
-//      HAL_ASSERT_SPINLOCK;
-//  }
+  switch (assertCause)
+  {
+    case HAL_ASSERT_CAUSE_OUT_OF_MEMORY:
+      Display_print0(dispHandle, 0, 0, "***ERROR***");
+      Display_print0(dispHandle, 2, 0, ">> OUT OF MEMORY!");
+      break;
+
+    case HAL_ASSERT_CAUSE_INTERNAL_ERROR:
+      // check the subcause
+      if (assertSubcause == HAL_ASSERT_SUBCAUSE_FW_INERNAL_ERROR)
+      {
+        Display_print0(dispHandle, 0, 0, "***ERROR***");
+        Display_print0(dispHandle, 2, 0, ">> INTERNAL FW ERROR!");
+      }
+      else
+      {
+        Display_print0(dispHandle, 0, 0, "***ERROR***");
+        Display_print0(dispHandle, 2, 0, ">> INTERNAL ERROR!");
+      }
+      break;
+
+    case HAL_ASSERT_CAUSE_ICALL_ABORT:
+      Display_print0(dispHandle, 0, 0, "***ERROR***");
+      Display_print0(dispHandle, 2, 0, ">> ICALL ABORT!");
+      HAL_ASSERT_SPINLOCK;
+      break;
+
+    default:
+      Display_print0(dispHandle, 0, 0, "***ERROR***");
+      Display_print0(dispHandle, 2, 0, ">> DEFAULT SPINLOCK!");
+      HAL_ASSERT_SPINLOCK;
+  }
+*/
 
   return;
 }

simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/python/update_elite_version.py

@@ -0,0 +1,33 @@
+# $python .\simplelink\ble_sdk_2_02_02_25\src\examples\simple_peripheral\cc26xx\app\python\update_elite_version.py
+
+import datetime
+import os
+
+print(datetime.datetime.now())
+# print(datetime.datetime.now().year)
+# print(datetime.datetime.now().month)
+# print(datetime.datetime.now().day)
+# print(datetime.datetime.now().hour)
+# print(datetime.datetime.now().minute)
+# print(datetime.datetime.now().strftime("%H:%M:%S"))
+
+y = datetime.datetime.now().year % 100
+m = datetime.datetime.now().month
+d = datetime.datetime.now().day
+hour = datetime.datetime.now().hour
+minute = datetime.datetime.now().minute
+
+path = os.getcwd()
+path += '/simplelink/ble_sdk_2_02_02_25/src/examples/simple_peripheral/cc26xx/app/headstage/Elite_version.h'
+print('save:', path)
+
+with open(path, 'w') as f:
+    f.write('#ifndef VERSION_DATE\t\t' + '\n')
+    f.write('#define VERSION_DATE\t\t' + '\n\n')
+    f.write('#define VERSION_DATE_YEAR\t\t' + str(y) + '\n')
+    f.write('#define VERSION_DATE_MONTH\t\t' + str(m) + '\n')
+    f.write('#define VERSION_DATE_DAY\t\t' + str(d) + '\n')
+    f.write('#define VERSION_DATE_HOUR\t\t' + str(hour) + '\n')
+    f.write('#define VERSION_DATE_MINUTE\t\t' + str(minute) + '\n')
+
+    f.write('#endif' + '\n\n')

simplelink/ble_sdk_2_02_02_25/src/profiles/simple_profile/cc26xx/simple_gatt_profile.c

@@ -50,7 +50,6 @@
  */
 #include <string.h>
 
-// clang-format off
 #include "bcomdef.h"
 #include "osal.h"
 #include "linkdb.h"
@@ -59,21 +58,61 @@
 #include "gatt_uuid.h"
 #include "gattservapp.h"
 #include "gapbondmgr.h"
-// clang-format on
 
 #include "simple_gatt_profile.h"
 
-#define _UUID(_uuid) \
-    { LO_UINT16(_uuid), HI_UINT16(_uuid) }
+/*********************************************************************
+ * MACROS
+ */
 
-CONST uint8 simpleProfileServUUID[ATT_BT_UUID_SIZE]  = _UUID(SIMPLEPROFILE_SERV_UUID);   // Simple GATT Profile Service UUID: 0xFFF0
-CONST uint8 simpleProfilechar1UUID[ATT_BT_UUID_SIZE] = _UUID(SIMPLEPROFILE_CHAR1_UUID);  // Characteristic 1 UUID: 0xFFF1
-CONST uint8 simpleProfilechar2UUID[ATT_BT_UUID_SIZE] = _UUID(SIMPLEPROFILE_CHAR2_UUID);  // Characteristic 2 UUID: 0xFFF2
-CONST uint8 simpleProfilechar3UUID[ATT_BT_UUID_SIZE] = _UUID(SIMPLEPROFILE_CHAR3_UUID);  // Characteristic 3 UUID: 0xFFF3
-CONST uint8 simpleProfilechar4UUID[ATT_BT_UUID_SIZE] = _UUID(SIMPLEPROFILE_CHAR4_UUID);  // Characteristic 4 UUID: 0xFFF4
-CONST uint8 simpleProfilechar5UUID[ATT_BT_UUID_SIZE] = _UUID(SIMPLEPROFILE_CHAR5_UUID);  // Characteristic 5 UUID: 0xFFF5
+/*********************************************************************
+ * CONSTANTS
+ */
 
-#undef _UUID
+#define SERVAPP_NUM_ATTR_SUPPORTED        17
+
+/*********************************************************************
+ * TYPEDEFS
+ */
+
+/*********************************************************************
+ * GLOBAL VARIABLES
+ */
+// Simple GATT Profile Service UUID: 0xFFF0
+CONST uint8 simpleProfileServUUID[ATT_BT_UUID_SIZE] =
+{
+  LO_UINT16(SIMPLEPROFILE_SERV_UUID), HI_UINT16(SIMPLEPROFILE_SERV_UUID)
+};
+
+// Characteristic 1 UUID: 0xFFF1
+CONST uint8 simpleProfilechar1UUID[ATT_BT_UUID_SIZE] =
+{
+  LO_UINT16(SIMPLEPROFILE_CHAR1_UUID), HI_UINT16(SIMPLEPROFILE_CHAR1_UUID)
+};
+
+// Characteristic 2 UUID: 0xFFF2
+CONST uint8 simpleProfilechar2UUID[ATT_BT_UUID_SIZE] =
+{
+  LO_UINT16(SIMPLEPROFILE_CHAR2_UUID), HI_UINT16(SIMPLEPROFILE_CHAR2_UUID)
+};
+
+// Characteristic 3 UUID: 0xFFF3
+CONST uint8 simpleProfilechar3UUID[ATT_BT_UUID_SIZE] =
+{
+  LO_UINT16(SIMPLEPROFILE_CHAR3_UUID), HI_UINT16(SIMPLEPROFILE_CHAR3_UUID)
+};
+
+// Characteristic 4 UUID: 0xFFF4
+CONST uint8 simpleProfilechar4UUID[ATT_BT_UUID_SIZE] =
+{
+  LO_UINT16(SIMPLEPROFILE_CHAR4_UUID), HI_UINT16(SIMPLEPROFILE_CHAR4_UUID)
+};
+
+// Characteristic 5 UUID: 0xFFF5
+CONST uint8 simpleProfilechar5UUID[ATT_BT_UUID_SIZE] =
+{
+  LO_UINT16(SIMPLEPROFILE_CHAR5_UUID), HI_UINT16(SIMPLEPROFILE_CHAR5_UUID)
+};
 
 /*********************************************************************
  * EXTERNAL VARIABLES
@@ -94,30 +133,50 @@ static simpleProfileCBs_t *simpleProfile_AppCBs = NULL;
  */
 
 // Simple Profile Service attribute
-static CONST gattAttrType_t simpleProfileService = {ATT_BT_UUID_SIZE, simpleProfileServUUID};
+static CONST gattAttrType_t simpleProfileService = { ATT_BT_UUID_SIZE, simpleProfileServUUID };
 
 // Simple Profile Characteristic 1 Properties
+// static uint8 simpleProfileChar1Props = GATT_PROP_READ | GATT_PROP_WRITE;
+/*user insert*/
 static uint8 simpleProfileChar1Props = GATT_PROP_READ;
 
 // Characteristic 1 Value
+// static uint8 simpleProfileChar1 = 0;
+/*user insert*/
+#define SIMPLEPROFILE_CHAR1_LEN 20
 static uint8 simpleProfileChar1[SIMPLEPROFILE_CHAR1_LEN] = {0};
 
+// Simple Profile Characteristic 1 User Description
+static uint8 simpleProfileChar1UserDesp[17] = "Characteristic 1";
+
 // Simple Profile Characteristic 2 Properties
 static uint8 simpleProfileChar2Props = GATT_PROP_READ;
 
 // Characteristic 2 Value
+// static uint8 simpleProfileChar2 = 0;
+/*user insert*/
 static uint8 simpleProfileChar2[SIMPLEPROFILE_CHAR2_LEN] = {0};
 
+// Simple Profile Characteristic 2 User Description
+static uint8 simpleProfileChar2UserDesp[17] = "Characteristic 2";
+
 // Simple Profile Characteristic 3 Properties
 static uint8 simpleProfileChar3Props = GATT_PROP_WRITE;
 
 // Characteristic 3 Value
+// static uint8 simpleProfileChar3 = 0;
+/*user insert*/
 static uint8 simpleProfileChar3[SIMPLEPROFILE_CHAR3_LEN] = {0};
 
+// Simple Profile Characteristic 3 User Description
+static uint8 simpleProfileChar3UserDesp[17] = "Characteristic 3";
+
 // Simple Profile Characteristic 4 Properties
 static uint8 simpleProfileChar4Props = GATT_PROP_NOTIFY;
 
 // Characteristic 4 Value
+// static uint8 simpleProfileChar4 = 0;
+/*user insert*/
 static uint8 simpleProfileChar4[SIMPLEPROFILE_CHAR4_LEN] = {0};
 
 // Simple Profile Characteristic 4 Configuration Each client has its own
@@ -126,89 +185,175 @@ static uint8 simpleProfileChar4[SIMPLEPROFILE_CHAR4_LEN] = {0};
 // that client and writes only affect the configuration of that client.
 static gattCharCfg_t *simpleProfileChar4Config;
 
+// Simple Profile Characteristic 4 User Description
+static uint8 simpleProfileChar4UserDesp[17] = "Characteristic 4";
+
 // Simple Profile Characteristic 5 Properties
-static uint8 simpleProfileChar5Props = GATT_PROP_READ | GATT_PROP_WRITE;
+static uint8 simpleProfileChar5Props = GATT_PROP_READ;
 
 // Characteristic 5 Value
-static uint8 simpleProfileChar5[SIMPLEPROFILE_CHAR5_LEN] = {0};
+static uint8 simpleProfileChar5[SIMPLEPROFILE_CHAR5_LEN] = { 0, 0, 0, 0, 0 };
+
+// Simple Profile Characteristic 5 User Description
+static uint8 simpleProfileChar5UserDesp[17] = "Characteristic 5";
 
 /*********************************************************************
  * Profile Attributes - Table
  */
 
-#define SERVAPP_NUM_ATTR_SUPPORTED 17
-
-static gattAttribute_t simpleProfileAttrTbl[SERVAPP_NUM_ATTR_SUPPORTED] = {
-    // Simple Profile Service
-    {{ATT_BT_UUID_SIZE, primaryServiceUUID}, GATT_PERMIT_READ, 0, (uint8 *)&simpleProfileService},
+static gattAttribute_t simpleProfileAttrTbl[SERVAPP_NUM_ATTR_SUPPORTED] =
+{
+  // Simple Profile Service
+  {
+    { ATT_BT_UUID_SIZE, primaryServiceUUID }, /* type */
+    GATT_PERMIT_READ,                         /* permissions */
+    0,                                        /* handle */
+    (uint8 *)&simpleProfileService            /* pValue */
+  },
 
     // Characteristic 1 Declaration
-    {{ATT_BT_UUID_SIZE, characterUUID}, GATT_PERMIT_READ, 0, &simpleProfileChar1Props},
+    {
+      { ATT_BT_UUID_SIZE, characterUUID },
+      GATT_PERMIT_READ,
+      0,
+      &simpleProfileChar1Props
+    },
 
-    // Characteristic Value 1
-    {{ATT_BT_UUID_SIZE, simpleProfilechar1UUID}, GATT_PERMIT_READ, 0, simpleProfileChar1},
+      // Characteristic Value 1
+      {
+        { ATT_BT_UUID_SIZE, simpleProfilechar1UUID },
+      	GATT_PERMIT_READ,
+      	0,
+      	simpleProfileChar1
+      },
 
-    // Characteristic 1 User Description
-    {{ATT_BT_UUID_SIZE, charUserDescUUID}, GATT_PERMIT_READ, 0, "FS"},
+      // Characteristic 1 User Description
+      {
+        { ATT_BT_UUID_SIZE, charUserDescUUID },
+    	GATT_PERMIT_READ,
+    	0,
+    	simpleProfileChar1UserDesp
+      },
 
     // Characteristic 2 Declaration
-    {{ATT_BT_UUID_SIZE, characterUUID}, GATT_PERMIT_READ, 0, &simpleProfileChar2Props},
+    {
+      { ATT_BT_UUID_SIZE, characterUUID },
+      GATT_PERMIT_READ,
+      0,
+      &simpleProfileChar2Props
+    },
+
+      // Characteristic Value 2
+      {
+        { ATT_BT_UUID_SIZE, simpleProfilechar2UUID },
+	    GATT_PERMIT_READ,
+	    0,
+	    simpleProfileChar2
+	  },
+	  
+	  // Characteristic 2 User Description
+	  {
+	    { ATT_BT_UUID_SIZE, charUserDescUUID }, 
+	    GATT_PERMIT_READ, 
+	    0, 
+	    simpleProfileChar2UserDesp
+	  },
 
-    // Characteristic Value 2
-    {{ATT_BT_UUID_SIZE, simpleProfilechar2UUID}, GATT_PERMIT_READ, 0, simpleProfileChar2},
 
-    // Characteristic 2 User Description
-    {{ATT_BT_UUID_SIZE, charUserDescUUID}, GATT_PERMIT_READ, 0, "CR"},
 
     // Characteristic 3 Declaration
-    {{ATT_BT_UUID_SIZE, characterUUID}, GATT_PERMIT_READ, 0, &simpleProfileChar3Props},
+    {
+      { ATT_BT_UUID_SIZE, characterUUID }, 
+      GATT_PERMIT_READ, 
+      0, 
+      &simpleProfileChar3Props
+    },
 
     // Characteristic Value 3
-    {{ATT_BT_UUID_SIZE, simpleProfilechar3UUID}, GATT_PERMIT_WRITE, 0, simpleProfileChar3},
+    {
+      { ATT_BT_UUID_SIZE, simpleProfilechar3UUID }, 
+      GATT_PERMIT_WRITE, 
+      0, 
+      simpleProfileChar3
+    },
 
     // Characteristic 3 User Description
-    {{ATT_BT_UUID_SIZE, charUserDescUUID}, GATT_PERMIT_READ, 0, "IS"},
+    {
+      { ATT_BT_UUID_SIZE, charUserDescUUID }, 
+      GATT_PERMIT_READ, 
+      0, 
+      simpleProfileChar3UserDesp
+    },
 
     // Characteristic 4 Declaration
-    {{ATT_BT_UUID_SIZE, characterUUID}, GATT_PERMIT_READ, 0, &simpleProfileChar4Props},
+    {
+      { ATT_BT_UUID_SIZE, characterUUID }, 
+      GATT_PERMIT_READ, 
+      0,
+      &simpleProfileChar4Props
+    },
 
     // Characteristic Value 4
-    {{ATT_BT_UUID_SIZE, simpleProfilechar4UUID}, 0, 0, simpleProfileChar4},
+    {
+      { ATT_BT_UUID_SIZE, simpleProfilechar4UUID }, 
+      0, 
+      0, 
+      simpleProfileChar4
+    },
 
     // Characteristic 4 configuration
-    {{ATT_BT_UUID_SIZE, clientCharCfgUUID}, GATT_PERMIT_READ | GATT_PERMIT_WRITE, 0, (uint8 *)&simpleProfileChar4Config},
+    {
+      { ATT_BT_UUID_SIZE, clientCharCfgUUID }, 
+      GATT_PERMIT_READ | GATT_PERMIT_WRITE, 
+      0, 
+      (uint8 *)&simpleProfileChar4Config
+    },
 
     // Characteristic 4 User Description
-    {{ATT_BT_UUID_SIZE, charUserDescUUID}, GATT_PERMIT_READ, 0, "Nt"},
+    {
+      { ATT_BT_UUID_SIZE, charUserDescUUID }, 
+      GATT_PERMIT_READ, 
+      0, 
+      simpleProfileChar4UserDesp
+    },
 
     // Characteristic 5 Declaration
-    {{ATT_BT_UUID_SIZE, characterUUID}, GATT_PERMIT_READ, 0, &simpleProfileChar5Props},
+    {
+      { ATT_BT_UUID_SIZE, characterUUID }, 
+      GATT_PERMIT_READ, 
+      0, 
+      &simpleProfileChar5Props
+    },
 
     // Characteristic Value 5
-    {{ATT_BT_UUID_SIZE, simpleProfilechar5UUID}, GATT_PERMIT_READ | GATT_PERMIT_WRITE, 0, simpleProfileChar5},
-    // GATT_PERMIT_AUTHEN_READ,
+    {
+      { ATT_BT_UUID_SIZE, simpleProfilechar5UUID }, 
+      GATT_PERMIT_AUTHEN_READ, 
+      0, 
+      simpleProfileChar5
+    },
 
     // Characteristic 5 User Description
-    {{ATT_BT_UUID_SIZE, charUserDescUUID}, GATT_PERMIT_READ, 0, "Dg"},
+    {
+      { ATT_BT_UUID_SIZE, charUserDescUUID }, 
+      GATT_PERMIT_READ, 
+      0, 
+      simpleProfileChar5UserDesp
+    },
 };
 
 /*********************************************************************
  * LOCAL FUNCTIONS
  */
-static bStatus_t simpleProfile_ReadAttrCB(uint16_t         connHandle,  //
-                                          gattAttribute_t *pAttr,
-                                          uint8_t *        pValue,
-                                          uint16_t *       pLen,
-                                          uint16_t         offset,
-                                          uint16_t         maxLen,
-                                          uint8_t          method);
-
-static bStatus_t simpleProfile_WriteAttrCB(uint16_t         connHandle,  //
-                                           gattAttribute_t *pAttr,
-                                           uint8_t *        pValue,
-                                           uint16_t         len,
-                                           uint16_t         offset,
-                                           uint8_t          method);
+static bStatus_t simpleProfile_ReadAttrCB(uint16_t connHandle,
+										  gattAttribute_t *pAttr,
+										  uint8_t *pValue, uint16_t *pLen,
+										  uint16_t offset, uint16_t maxLen,
+										  uint8_t method);
+static bStatus_t simpleProfile_WriteAttrCB(uint16_t connHandle,
+										   gattAttribute_t *pAttr,
+										   uint8_t *pValue, uint16_t len,
+										   uint16_t offset, uint8_t method);
 
 /*********************************************************************
  * PROFILE CALLBACKS
@@ -222,10 +367,11 @@ static bStatus_t simpleProfile_WriteAttrCB(uint16_t         connHandle,  //
 // pfnAuthorizeAttrCB to check a client's authorization prior to calling
 // pfnReadAttrCB or pfnWriteAttrCB, so no checks for authorization need to be
 // made within these functions.
-CONST gattServiceCBs_t simpleProfileCBs = {
-    simpleProfile_ReadAttrCB,   // Read callback function pointer
-    simpleProfile_WriteAttrCB,  // Write callback function pointer
-    NULL                        // Authorization callback function pointer
+CONST gattServiceCBs_t simpleProfileCBs =
+{
+  simpleProfile_ReadAttrCB,  // Read callback function pointer
+  simpleProfile_WriteAttrCB, // Write callback function pointer
+  NULL                       // Authorization callback function pointer
 };
 
 /*********************************************************************
@@ -243,29 +389,35 @@ CONST gattServiceCBs_t simpleProfileCBs = {
  *
  * @return  Success or Failure
  */
-bStatus_t SimpleProfile_AddService(uint32 services) {
-    uint8 status;
+bStatus_t SimpleProfile_AddService( uint32 services )
+{
+  uint8 status;
 
-    // Allocate Client Characteristic Configuration table
-    simpleProfileChar4Config = (gattCharCfg_t *)ICall_malloc(sizeof(gattCharCfg_t) * linkDBNumConns);
-    if (simpleProfileChar4Config == NULL) {
-        return (bleMemAllocError);
-    }
+  // Allocate Client Characteristic Configuration table
+  simpleProfileChar4Config = (gattCharCfg_t *)ICall_malloc( sizeof(gattCharCfg_t) *
+  														    linkDBNumConns );
+  if ( simpleProfileChar4Config == NULL )
+  {
+    return ( bleMemAllocError );
+  }
 
-    // Initialize Client Characteristic Configuration attributes
-    GATTServApp_InitCharCfg(INVALID_CONNHANDLE, simpleProfileChar4Config);
+  // Initialize Client Characteristic Configuration attributes
+  GATTServApp_InitCharCfg( INVALID_CONNHANDLE, simpleProfileChar4Config );
 
-    if (services & SIMPLEPROFILE_SERVICE) {
-        // Register GATT attribute list and CBs with GATT Server App
-        status = GATTServApp_RegisterService(simpleProfileAttrTbl,  //
-                                             GATT_NUM_ATTRS(simpleProfileAttrTbl),
-                                             GATT_MAX_ENCRYPT_KEY_SIZE,
-                                             &simpleProfileCBs);
-    } else {
-        status = SUCCESS;
-    }
+  if ( services & SIMPLEPROFILE_SERVICE )
+  {
+    // Register GATT attribute list and CBs with GATT Server App
+    status = GATTServApp_RegisterService( simpleProfileAttrTbl,
+    									  GATT_NUM_ATTRS( simpleProfileAttrTbl ),
+    									  GATT_MAX_ENCRYPT_KEY_SIZE,
+    									  &simpleProfileCBs );
+  }
+  else
+  {
+    status = SUCCESS;
+  }
 
-    return (status);
+  return ( status );
 }
 
 /*********************************************************************
@@ -278,14 +430,18 @@ bStatus_t SimpleProfile_AddService(uint32 services) {
  *
  * @return  SUCCESS or bleAlreadyInRequestedMode
  */
-bStatus_t SimpleProfile_RegisterAppCBs(simpleProfileCBs_t *appCallbacks) {
-    if (appCallbacks) {
-        simpleProfile_AppCBs = appCallbacks;
+bStatus_t SimpleProfile_RegisterAppCBs( simpleProfileCBs_t *appCallbacks )
+{
+  if ( appCallbacks )
+  {
+    simpleProfile_AppCBs = appCallbacks;
 
-        return (SUCCESS);
-    } else {
-        return (bleAlreadyInRequestedMode);
-    }
+    return ( SUCCESS );
+  }
+  else
+  {
+    return ( bleAlreadyInRequestedMode );
+  }
 }
 
 /*********************************************************************
@@ -302,60 +458,76 @@ bStatus_t SimpleProfile_RegisterAppCBs(simpleProfileCBs_t *appCallbacks) {
  *
  * @return  bStatus_t
  */
-bStatus_t SimpleProfile_SetParameter(uint8 param, uint8 len, void *value) {
-    switch (param) {
-        case SIMPLEPROFILE_CHAR1:
-            if (len <= SIMPLEPROFILE_CHAR1_LEN) {
-                memcpy(simpleProfileChar1, value, len);
-                return SUCCESS;
-            } else {
-                return bleInvalidRange;
-            }
+bStatus_t SimpleProfile_SetParameter( uint8 param, uint8 len, void *value )
+{
+  bStatus_t ret = SUCCESS;
+  switch ( param )
+  {
+    case SIMPLEPROFILE_CHAR1:
+      if ( len <= SIMPLEPROFILE_CHAR1_LEN )
+      {
+        memcpy(simpleProfileChar1, value, len);
+        // simpleProfileChar1 = *((uint8*)value);
+      } 
+      else
+      {
+        ret = bleInvalidRange;
+      }
+      break;
 
-        case SIMPLEPROFILE_CHAR2:
-            if (len <= SIMPLEPROFILE_CHAR2_LEN) {
-                memcpy(simpleProfileChar2, value, len);
-                return SUCCESS;
-            } else {
-                return bleInvalidRange;
-            }
+    case SIMPLEPROFILE_CHAR2:
+      if (len <= SIMPLEPROFILE_CHAR2_LEN) 
+      {
+        memcpy(simpleProfileChar2, value, len);
+        // simpleProfileChar2 = *((uint8*)value);
+      }
+      else
+	  {
+        ret = bleInvalidRange;
+      }
+      break;
 
-        case SIMPLEPROFILE_CHAR3:
-            if (len <= SIMPLEPROFILE_CHAR3_LEN) {
-                memcpy(simpleProfileChar3, value, len);
-                return SUCCESS;
-            } else {
-                return bleInvalidRange;
-            }
+    case SIMPLEPROFILE_CHAR3:
+      if (len <= SIMPLEPROFILE_CHAR3_LEN) 
+      {
+        memcpy(simpleProfileChar3, value, len);
+      } 
+      else
+      {
+        ret = bleInvalidRange;
+      }
+      break;
 
-        case SIMPLEPROFILE_CHAR4:
-            if (len <= SIMPLEPROFILE_CHAR4_LEN) {
-                memcpy(simpleProfileChar4, value, len);
+    case SIMPLEPROFILE_CHAR4:
+      if (len <= SIMPLEPROFILE_CHAR4_LEN)
+      {
+        memcpy(simpleProfileChar4, value, len);
 
-                // See if Notification has been enabled
-                GATTServApp_ProcessCharCfg(simpleProfileChar4Config,  //
-                                           simpleProfileChar4,
-                                           FALSE,
-                                           simpleProfileAttrTbl,
-                                           GATT_NUM_ATTRS(simpleProfileAttrTbl),
-                                           INVALID_TASK_ID,
-                                           simpleProfile_ReadAttrCB);
-                return SUCCESS;
-            } else {
-                return bleInvalidRange;
-            }
+        // See if Notification has been enabled
+        GATTServApp_ProcessCharCfg(simpleProfileChar4Config, simpleProfileChar4, FALSE, simpleProfileAttrTbl, GATT_NUM_ATTRS(simpleProfileAttrTbl), INVALID_TASK_ID, simpleProfile_ReadAttrCB);
+      }
+      else
+      {
+        ret = bleInvalidRange;
+      }
+      break;
 
-        case SIMPLEPROFILE_CHAR5:
-            if (len <= SIMPLEPROFILE_CHAR5_LEN) {
-                memcpy(simpleProfileChar5, value, len);
-                return SUCCESS;
-            } else {
-                return bleInvalidRange;
-            }
+    case SIMPLEPROFILE_CHAR5:
+      if (len == SIMPLEPROFILE_CHAR5_LEN) {
+        VOID memcpy(simpleProfileChar5, value, SIMPLEPROFILE_CHAR5_LEN);
+      }
+      else
+      {
+        ret = bleInvalidRange;
+      }
+      break;
 
-        default:
-            return INVALIDPARAMETER;
-    }
+    default:
+      ret = INVALIDPARAMETER;
+      break;
+  }
+
+  return ( ret );
 }
 
 /*********************************************************************
@@ -372,32 +544,36 @@ bStatus_t SimpleProfile_SetParameter(uint8 param, uint8 len, void *value) {
  * @return  bStatus_t
  */
 bStatus_t SimpleProfile_GetParameter(uint8 param, void *value) {
+    bStatus_t ret = SUCCESS;
     switch (param) {
-        case SIMPLEPROFILE_CHAR1:
-            memcpy(value, simpleProfileChar1, SIMPLEPROFILE_CHAR1_LEN);
-            break;
+    case SIMPLEPROFILE_CHAR1:
+        memcpy(value, simpleProfileChar1, SIMPLEPROFILE_CHAR1_LEN);
+        //      *((uint8*)value) = simpleProfileChar1;
+        break;
 
-        case SIMPLEPROFILE_CHAR2:
-            memcpy(value, simpleProfileChar2, SIMPLEPROFILE_CHAR2_LEN);
-            break;
+    case SIMPLEPROFILE_CHAR2:
+        memcpy(value, simpleProfileChar2, SIMPLEPROFILE_CHAR2_LEN);
+        //      *((uint8*)value) = simpleProfileChar2;
+        break;
 
-        case SIMPLEPROFILE_CHAR3:
-            memcpy(value, simpleProfileChar3, SIMPLEPROFILE_CHAR3_LEN);
-            break;
+    case SIMPLEPROFILE_CHAR3:
+        memcpy(value, simpleProfileChar3, SIMPLEPROFILE_CHAR3_LEN);
+        break;
 
-        case SIMPLEPROFILE_CHAR4:
-            memcpy(value, simpleProfileChar4, SIMPLEPROFILE_CHAR4_LEN);
-            break;
+    case SIMPLEPROFILE_CHAR4:
+        memcpy(value, simpleProfileChar4, SIMPLEPROFILE_CHAR4_LEN);
+        break;
 
-        case SIMPLEPROFILE_CHAR5:
-            memcpy(value, simpleProfileChar5, SIMPLEPROFILE_CHAR5_LEN);
-            break;
+    case SIMPLEPROFILE_CHAR5:
+        VOID memcpy(value, simpleProfileChar5, SIMPLEPROFILE_CHAR5_LEN);
+        break;
 
-        default:
-            return INVALIDPARAMETER;
+    default:
+        ret = INVALIDPARAMETER;
+        break;
     }
 
-    return SUCCESS;
+    return (ret);
 }
 
 /*********************************************************************
@@ -415,13 +591,7 @@ bStatus_t SimpleProfile_GetParameter(uint8 param, void *value) {
  *
  * @return      SUCCESS, blePending or Failure
  */
-static bStatus_t simpleProfile_ReadAttrCB(uint16_t         connHandle,  //
-                                          gattAttribute_t *pAttr,
-                                          uint8_t *        pValue,
-                                          uint16_t *       pLen,
-                                          uint16_t         offset,
-                                          uint16_t         maxLen,
-                                          uint8_t          method) {
+static bStatus_t simpleProfile_ReadAttrCB(uint16_t connHandle, gattAttribute_t *pAttr, uint8_t *pValue, uint16_t *pLen, uint16_t offset, uint16_t maxLen, uint8_t method) {
     bStatus_t status = SUCCESS;
 
     // Make sure it's not a blob operation (no attributes in the profile are long)
@@ -433,31 +603,42 @@ static bStatus_t simpleProfile_ReadAttrCB(uint16_t         connHandle,  //
         // 16-bit UUID
         uint16 uuid = BUILD_UINT16(pAttr->type.uuid[0], pAttr->type.uuid[1]);
         switch (uuid) {
-            case SIMPLEPROFILE_CHAR1_UUID:
-                *pLen = SIMPLEPROFILE_CHAR1_LEN;
-                memcpy(pValue, pAttr->pValue, SIMPLEPROFILE_CHAR1_LEN);
-                break;
+        // No need for "GATT_SERVICE_UUID" or "GATT_CLIENT_CHAR_CFG_UUID" cases;
+        // gattserverapp handles those reads
 
-            case SIMPLEPROFILE_CHAR2_UUID:
-                *pLen = SIMPLEPROFILE_CHAR2_LEN;
-                memcpy(pValue, pAttr->pValue, SIMPLEPROFILE_CHAR2_LEN);
-                break;
+        // characteristics 1 and 2 have read permissions
+        // characteritisc 3 does not have read permissions; therefore it is not
+        //   included here
+        // characteristic 4 does not have read permissions, but because it
+        //   can be sent as a notification, it is included here
+        case SIMPLEPROFILE_CHAR1_UUID:
+            *pLen = SIMPLEPROFILE_CHAR1_LEN;
+            VOID memcpy(pValue, pAttr->pValue, SIMPLEPROFILE_CHAR1_LEN);
+            break;
 
-            case SIMPLEPROFILE_CHAR4_UUID:
-                *pLen = SIMPLEPROFILE_CHAR4_LEN;
-                memcpy(pValue, pAttr->pValue, SIMPLEPROFILE_CHAR4_LEN);
-                break;
+        case SIMPLEPROFILE_CHAR2_UUID:
+            //        *pLen = 1;
+            //        pValue[0] = *pAttr->pValue;
 
-            case SIMPLEPROFILE_CHAR5_UUID:
-                *pLen = SIMPLEPROFILE_CHAR5_LEN;
-                memcpy(pValue, pAttr->pValue, SIMPLEPROFILE_CHAR5_LEN);
-                break;
+            *pLen = SIMPLEPROFILE_CHAR2_LEN;
+            VOID memcpy(pValue, pAttr->pValue, SIMPLEPROFILE_CHAR2_LEN);
+            break;
 
-            default:
-                // Should never get here! (characteristics 3 and 4 do not have read permissions)
-                *pLen  = 0;
-                status = ATT_ERR_ATTR_NOT_FOUND;
-                break;
+        case SIMPLEPROFILE_CHAR4_UUID:
+            *pLen = SIMPLEPROFILE_CHAR4_LEN;
+            VOID memcpy(pValue, pAttr->pValue, SIMPLEPROFILE_CHAR4_LEN);
+            break;
+            //      case SIMPLEPROFILE_CHAR5_UUID:
+
+            //        *pLen = SIMPLEPROFILE_CHAR5_LEN;
+            //        VOID memcpy( pValue, pAttr->pValue, SIMPLEPROFILE_CHAR5_LEN );
+            //        break;
+
+        default:
+            // Should never get here! (characteristics 3 and 4 do not have read permissions)
+            *pLen  = 0;
+            status = ATT_ERR_ATTR_NOT_FOUND;
+            break;
         }
     } else {
         // 128-bit UUID
@@ -482,73 +663,71 @@ static bStatus_t simpleProfile_ReadAttrCB(uint16_t         connHandle,  //
  *
  * @return  SUCCESS, blePending or Failure
  */
-static bStatus_t simpleProfile_WriteAttrCB(uint16_t         connHandle,  //
-                                           gattAttribute_t *pAttr,
-                                           uint8_t *        pValue,
-                                           uint16_t         len,
-                                           uint16_t         offset,
-                                           uint8_t          method) {
+static bStatus_t simpleProfile_WriteAttrCB(uint16_t connHandle, gattAttribute_t *pAttr, uint8_t *pValue, uint16_t len, uint16_t offset, uint8_t method) {
     bStatus_t status    = SUCCESS;
     uint8     notifyApp = 0xFF;
 
     if (pAttr->type.len == ATT_BT_UUID_SIZE) {
         // 16-bit UUID
         uint16 uuid = BUILD_UINT16(pAttr->type.uuid[0], pAttr->type.uuid[1]);
-
         switch (uuid) {
-            case SIMPLEPROFILE_CHAR3_UUID:
+            // Validate the value
+            // Make sure it's not a blob oper
+            /*
+            if ( offset == 0 )
+            {
+              if ( len != 1 )
+              {
+                status = ATT_ERR_INVALID_VALUE_SIZE;
+              }
+            }
+            else
+            {
+              status = ATT_ERR_ATTR_NOT_LONG;
+            }
 
-                // Validate the value
-                // Make sure it's not a blob oper
-                if (offset == 0) {
-                    if (len >= SIMPLEPROFILE_CHAR3_LEN) {
-                        status = ATT_ERR_INVALID_VALUE_SIZE;
-                    }
-                } else {
-                    status = ATT_ERR_ATTR_NOT_LONG;
+            //Write the value
+            if ( status == SUCCESS )
+            {
+              uint8 *pCurValue = (uint8 *)pAttr->pValue;
+              *pCurValue = pValue[0];
+
+              if( pAttr->pValue == &simpleProfileChar1 )
+              {
+                notifyApp = SIMPLEPROFILE_CHAR1;
+              }
+            }
+
+            break;
+            */
+        case SIMPLEPROFILE_CHAR3_UUID:
+            if (offset == 0) {
+                if (len > SIMPLEPROFILE_CHAR3_LEN) {
+                    status = ATT_ERR_INVALID_VALUE_SIZE;
                 }
+            } else {
+                status = ATT_ERR_ATTR_NOT_LONG;
+            }
 
-                // Write the value
-                if (status == SUCCESS) {
-                    // Copy pValue into the variable we point to from the attribute table.
-                    memcpy(pAttr->pValue + offset, pValue, len);
-                    memset(pAttr->pValue + len, 0, SIMPLEPROFILE_CHAR3_LEN - len);
+            // Write the value
+            if (status == SUCCESS) {
+                // Copy pValue into the variable we point to from the attribute table.
+                memcpy(pAttr->pValue + offset, pValue, len);
+                memset(pAttr->pValue + len, 0, SIMPLEPROFILE_CHAR3_LEN - len);
 
-                    if (pAttr->pValue == simpleProfileChar3) {
-                        notifyApp = SIMPLEPROFILE_CHAR3;
-                    }
+                if (pAttr->pValue == simpleProfileChar3) {
+                    notifyApp = SIMPLEPROFILE_CHAR3;
                 }
+            }
 
-                break;
-            case SIMPLEPROFILE_CHAR5_UUID:
-                if (offset == 0) {
-                    if (len >= SIMPLEPROFILE_CHAR5_LEN) {
-                        status = ATT_ERR_INVALID_VALUE_SIZE;
-                    }
-                } else {
-                    status = ATT_ERR_ATTR_NOT_LONG;
-                }
-
-                // Write the value
-                if (status == SUCCESS) {
-                    // Copy pValue into the variable we point to from the attribute table.
-                    memcpy(pAttr->pValue + offset, pValue, len);
-                    memset(pAttr->pValue + len, 0, SIMPLEPROFILE_CHAR5_LEN - len);
-
-                    if (pAttr->pValue == simpleProfileChar5) {
-                        notifyApp = SIMPLEPROFILE_CHAR5;
-                    }
-                }
-
-                break;
-            case GATT_CLIENT_CHAR_CFG_UUID:
-                status = GATTServApp_ProcessCCCWriteReq(connHandle, pAttr, pValue, len, offset, GATT_CLIENT_CFG_NOTIFY);
-                break;
-
-            default:
-                // Should never get here! (characteristics 2 and 4 do not have write permissions)
-                status = ATT_ERR_ATTR_NOT_FOUND;
-                break;
+            break;
+        case GATT_CLIENT_CHAR_CFG_UUID:
+            status = GATTServApp_ProcessCCCWriteReq(connHandle, pAttr, pValue, len, offset, GATT_CLIENT_CFG_NOTIFY);
+            break;
+        default:
+            // Should never get here! (characteristics 2 and 4 do not have write permissions)
+            status = ATT_ERR_ATTR_NOT_FOUND;
+            break;
         }
     } else {
         // 128-bit UUID

simplelink/ble_sdk_2_02_02_25/src/profiles/simple_profile/simple_gatt_profile.h

@@ -9,7 +9,7 @@
  Target Device: CC2650, CC2640
 
  ******************************************************************************
-
+ 
  Copyright (c) 2010-2018, Texas Instruments Incorporated
  All rights reserved.
 
@@ -49,7 +49,8 @@
 #define SIMPLEGATTPROFILE_H
 
 #ifdef __cplusplus
-extern "C" {
+extern "C"
+{
 #endif
 
 /*********************************************************************
@@ -61,37 +62,36 @@ extern "C" {
  */
 
 // Profile Parameters
-#define SIMPLEPROFILE_CHAR1 0  // RW uint8 - Profile Characteristic 1 value
-#define SIMPLEPROFILE_CHAR2 1  // RW uint8 - Profile Characteristic 2 value
-#define SIMPLEPROFILE_CHAR3 2  // RW uint8 - Profile Characteristic 3 value
-#define SIMPLEPROFILE_CHAR4 3  // RW uint8 - Profile Characteristic 4 value
-#define SIMPLEPROFILE_CHAR5 4  // RW uint8 - Profile Characteristic 4 value
+#define SIMPLEPROFILE_CHAR1                   0  // RW uint8 - Profile Characteristic 1 value
+#define SIMPLEPROFILE_CHAR2                   1  // RW uint8 - Profile Characteristic 2 value
+#define SIMPLEPROFILE_CHAR3                   2  // RW uint8 - Profile Characteristic 3 value
+#define SIMPLEPROFILE_CHAR4                   3  // RW uint8 - Profile Characteristic 4 value
+#define SIMPLEPROFILE_CHAR5                   4  // RW uint8 - Profile Characteristic 4 value
 
 // Simple Profile Service UUID
-#define SIMPLEPROFILE_SERV_UUID 0xFFF0
+#define SIMPLEPROFILE_SERV_UUID               0xFFF0
 
 // Key Pressed UUID
-#define SIMPLEPROFILE_CHAR1_UUID 0xFFF1
-#define SIMPLEPROFILE_CHAR2_UUID 0xFFF2
-#define SIMPLEPROFILE_CHAR3_UUID 0xFFF3
-#define SIMPLEPROFILE_CHAR4_UUID 0xFFF4
-#define SIMPLEPROFILE_CHAR5_UUID 0xFFF5
+#define SIMPLEPROFILE_CHAR1_UUID            0xFFF1
+#define SIMPLEPROFILE_CHAR2_UUID            0xFFF2
+#define SIMPLEPROFILE_CHAR3_UUID            0xFFF3
+#define SIMPLEPROFILE_CHAR4_UUID            0xFFF4
+#define SIMPLEPROFILE_CHAR5_UUID            0xFFF5
 
 // Simple Keys Profile Services bit fields
-#define SIMPLEPROFILE_SERVICE 0x00000001
+#define SIMPLEPROFILE_SERVICE               0x00000001
 
 // Length of Characteristic 5 in bytes
-#define SIMPLEPROFILE_CHAR1_LEN 2
-#define SIMPLEPROFILE_CHAR2_LEN 10
-#define SIMPLEPROFILE_CHAR3_LEN 20
-#define SIMPLEPROFILE_CHAR4_LEN 200
-//#define SIMPLEPROFILE_CHAR4_LEN 20
-#define SIMPLEPROFILE_CHAR5_LEN 20
-
+#define SIMPLEPROFILE_CHAR5_LEN           5
+/*user insert*/
+#define SIMPLEPROFILE_CHAR4_LEN           40
+#define SIMPLEPROFILE_CHAR3_LEN           20
+#define SIMPLEPROFILE_CHAR2_LEN           20
 /*********************************************************************
  * TYPEDEFS
  */
 
+
 /*********************************************************************
  * MACROS
  */
@@ -101,16 +101,20 @@ extern "C" {
  */
 
 // Callback when a characteristic value has changed
-typedef void (*simpleProfileChange_t)(uint8 paramID);
+typedef void (*simpleProfileChange_t)( uint8 paramID );
 
-typedef struct {
-    simpleProfileChange_t pfnSimpleProfileChange;  // Called when characteristic value changes
+typedef struct
+{
+  simpleProfileChange_t        pfnSimpleProfileChange;  // Called when characteristic value changes
 } simpleProfileCBs_t;
 
+
+
 /*********************************************************************
  * API FUNCTIONS
  */
 
+
 /*
  * SimpleProfile_AddService- Initializes the Simple GATT Profile service by registering
  *          GATT attributes with the GATT server.
@@ -119,7 +123,7 @@ typedef struct {
  *                     contain more than one service.
  */
 
-extern bStatus_t SimpleProfile_AddService(uint32 services);
+extern bStatus_t SimpleProfile_AddService( uint32 services );
 
 /*
  * SimpleProfile_RegisterAppCBs - Registers the application callback function.
@@ -127,7 +131,7 @@ extern bStatus_t SimpleProfile_AddService(uint32 services);
  *
  *    appCallbacks - pointer to application callbacks.
  */
-extern bStatus_t SimpleProfile_RegisterAppCBs(simpleProfileCBs_t *appCallbacks);
+extern bStatus_t SimpleProfile_RegisterAppCBs( simpleProfileCBs_t *appCallbacks );
 
 /*
  * SimpleProfile_SetParameter - Set a Simple GATT Profile parameter.
@@ -139,7 +143,7 @@ extern bStatus_t SimpleProfile_RegisterAppCBs(simpleProfileCBs_t *appCallbacks);
  *          data type (example: data type of uint16 will be cast to
  *          uint16 pointer).
  */
-extern bStatus_t SimpleProfile_SetParameter(uint8 param, uint8 len, void *value);
+extern bStatus_t SimpleProfile_SetParameter( uint8 param, uint8 len, void *value );
 
 /*
  * SimpleProfile_GetParameter - Get a Simple GATT Profile parameter.
@@ -150,7 +154,8 @@ extern bStatus_t SimpleProfile_SetParameter(uint8 param, uint8 len, void *value)
  *          data type (example: data type of uint16 will be cast to
  *          uint16 pointer).
  */
-extern bStatus_t SimpleProfile_GetParameter(uint8 param, void *value);
+extern bStatus_t SimpleProfile_GetParameter( uint8 param, void *value );
+
 
 /*********************************************************************
 *********************************************************************/