refactor: comment out unused fields in CaptureSample_t and streamline capture logging

pec930_sdk-v1.0.1/Examples/template/PFC_LLC_2026-05-20_2P2Z_ok/inc/app.h

@@ -10,7 +10,6 @@ extern "C"
 {
 #endif
 
-#include "isr.h"
 #include "main.h"
 
   //=============================================================================
@@ -27,6 +26,7 @@ extern "C"
 /* flash*/
 #define FLASH_PROG_ADDR_END       sizeof(EFLASH_MEM_Type)
 #define FLASH_PROG_ADDR_USER_CALI (FLASH_PROG_ADDR_END - FLASH_1_PAGE_SIZE) // 0x8000-512
+#define FLASH_PARAM_MAGIC         0x50464C54U
 
   //=============================================================================
   //                  Structure Definition
@@ -39,6 +39,14 @@ extern "C"
     int32_t a1;
     int32_t a2;
   };
+
+  struct flash_bode_plot_blob_t
+  {
+    uint32_t magic;
+    struct bode_plot_param_t cloop;
+    struct bode_plot_param_t vloop;
+    uint32_t reserved;
+  };
   //=============================================================================
   //                  Global Data Definition
   //=============================================================================
@@ -64,9 +72,11 @@ extern "C"
   void uart_cmd_parse(char *cmd_buf, uint32_t size);
 
   /* flash */
-  void bode_plot_param_read_from_flash(struct bode_plot_param_t *param, uint32_t addr);
+  int write_bodeplot_params_to_flash(const struct bode_plot_param_t *cloop, const struct bode_plot_param_t *vloop, uint32_t addr);
-
+  void read_bodeplot_params_from_flash(struct bode_plot_param_t *cloop, struct bode_plot_param_t *vloop, uint32_t addr);
-  extern struct bode_plot_param_t bode_plot_param;
+  void peek_bodeplot_params_in_flash(uint32_t addr);
+  void print_bodeplot_params(struct bode_plot_param_t *cloop, struct bode_plot_param_t *vloop);
+  extern struct bode_plot_param_t pfc_cloop_bode_plot_param;
   extern struct bode_plot_param_t pfc_vloop_bode_plot_param;
 
 #ifdef __cplusplus

pec930_sdk-v1.0.1/Examples/template/PFC_LLC_2026-05-20_2P2Z_ok/inc/init.h

@@ -1,8 +1,5 @@
-/*
+/**
- * init.h
+ * Copyright (c) 2026 Wisetop. All Rights Reserved.
- *
- *  Created on: 2025年10月9日
- *      Author: jim_liao
  */
 
 #ifndef INC_INIT_H_
@@ -10,18 +7,14 @@
 
 #include "main.h"
 
-void SYS_Config();
+void SYS_Config(void);
-void gpio_config();
+void sysclk_init(void);
-void opa_config();
+void gpio_init(void);
-void adc_config();
+void opa_init(void);
-//-------------------------------------
+void adc_init(void);
-void llc_pwm_config(); // LLC
+void tim0_init(void);
-
+void llc_pwm_init(void);
-//------------------------------------
+void pfc_pwm_init(void);
-void pfc_pwm_config(); // PFC
-
-//-----------------------------------
 void pwm_brake();
-void tim0_config();
 
 #endif /* INC_INIT_H_ */

pec930_sdk-v1.0.1/Examples/template/PFC_LLC_2026-05-20_2P2Z_ok/inc/isr.h

@@ -1,53 +0,0 @@
-/**
- * Copyright (c) 2024 Wei-Lun Hsu. All Rights Reserved.
- */
-/** @file isr.h
- *
- * @author Wei-Lun Hsu
- * @version 0.1
- * @date 2024/09/16
- * @license
- * @description
- */
-
-#ifndef __isr_H_wuraIpBA_lTJm_HvJw_sNDo_uEd5JnucTReY__
-#define __isr_H_wuraIpBA_lTJm_HvJw_sNDo_uEd5JnucTReY__
-
-#ifdef __cplusplus
-extern "C"
-{
-#endif
-
-#include "main.h"
-  //=============================================================================
-  //                  Constant Definition
-  //=============================================================================
-
-  //=============================================================================
-  //                  Macro Definition
-  //=============================================================================
-
-  //=============================================================================
-  //                  Structure Definition
-  //=============================================================================
-
-  //=============================================================================
-  //                  Global Data Definition
-  //=============================================================================
-
-  //=============================================================================
-  //                  Private Function Definition
-  //=============================================================================
-
-  //=============================================================================
-  //                  Public Function Definition
-  //=============================================================================
-  // void isr_tim2_handle(void);
-  // void isr_adc_handle(void);
-  // void isr_tim0_handle(void);
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif

pec930_sdk-v1.0.1/Examples/template/PFC_LLC_2026-05-20_2P2Z_ok/inc/main.h

@@ -108,6 +108,10 @@ extern "C"
   //=============================================================================
   //                  Public Function Definition
   //=============================================================================
+  extern uint8_t capture_continuous_mode;
+  extern int16_t capture_package_cnt;
+  extern uint16_t capture_packet_gap_ms;
+
   void Power_On();
   void Power_Off();
   void Key1_Scan();
@@ -126,6 +130,8 @@ extern "C"
   void isr_adc_handle(void);
   void isr_tim0_handle(void);
 
+  void capture_start(void);
+
 #ifdef __cplusplus
 }
 #endif

pec930_sdk-v1.0.1/Examples/template/PFC_LLC_2026-05-20_2P2Z_ok/src/app.c

@@ -8,11 +8,9 @@
 
 #define TICK_1000_MS 1000
 
-struct bode_plot_param_t bode_plot_param;
+struct bode_plot_param_t pfc_cloop_bode_plot_param;
 struct bode_plot_param_t pfc_vloop_bode_plot_param;
 
-static int bode_plot_param_write_to_flash(const struct bode_plot_param_t *param, uint32_t addr);
-
 /* sys clock*/
 static void sysclk_systick_init(SYSCFG_ClkSrcTypeDef clk_src, uint32_t sys_tick_ms)
 {
@@ -215,46 +213,90 @@ void uart_cmd_parse(char *cmd_buf, uint32_t size)
     msg("Available commands:\r\n");
     msg("  help        - show this help\r\n");
     msg("  version     - show firmware version\r\n");
-    msg("  bodeplot=B0,B1,B2,A1,A2\r\n");
+    msg("  cloop=B0,B1,B2,A1,A2\r\n");
-    msg("  bodeplot?   - show current bode plot parameters\r\n");
+    msg("  vloop=B0,B1,B2,A1,A2\r\n");
+    msg("  bodeplot?   - show runtime cloop & vloop bode plot parameters\r\n");
     msg("  flash_bodeplot? - show raw flash content for bode plot parameters\r\n");
+    msg("  notify_en=0 or notify_en=1 or notify_en=255,n\r\n");
+    msg("  notify_packet_gap=GAP_MS\r\n");
   }
   else if (strcmp(cmd_buf, "version") == 0)
   {
     msg("version: %s\r\n", "1.0.0");
   }
-  else if (cmd_match_with_arg(cmd_buf, "bodeplot=", &arg))
+  else if (cmd_match_with_arg(cmd_buf, "cloop=", &arg))
   {
-    struct bode_plot_param_t *bplot_p = &bode_plot_param;
+    struct bode_plot_param_t *cloop_p = &pfc_cloop_bode_plot_param;
-    if (parse_i32_csv5(arg, bplot_p))
+    struct bode_plot_param_t *vloop_p = &pfc_vloop_bode_plot_param;
+    if (parse_i32_csv5(arg, cloop_p))
     {
-      bode_plot_param_write_to_flash(bplot_p, FLASH_PROG_ADDR_USER_CALI);
+      write_bodeplot_params_to_flash(cloop_p, vloop_p, FLASH_PROG_ADDR_USER_CALI);
+      peek_bodeplot_params_in_flash(FLASH_PROG_ADDR_USER_CALI);
     }
     else
     {
-      msg("invalid bodeplot format, use: bodeplot=111,8,5,6,77\r\n");
+      msg("invalid cloop format, use: cloop=111,8,5,6,77\r\n");
+    }
+  }
+  else if (cmd_match_with_arg(cmd_buf, "vloop=", &arg))
+  {
+    struct bode_plot_param_t *cloop_p = &pfc_cloop_bode_plot_param;
+    struct bode_plot_param_t *vloop_p = &pfc_vloop_bode_plot_param;
+    if (parse_i32_csv5(arg, vloop_p))
+    {
+      write_bodeplot_params_to_flash(cloop_p, vloop_p, FLASH_PROG_ADDR_USER_CALI);
+      peek_bodeplot_params_in_flash(FLASH_PROG_ADDR_USER_CALI);
+    }
+    else
+    {
+      msg("invalid vloop format, use: vloop=111,8,5,6,77\r\n");
     }
   }
   else if (strcmp(cmd_buf, "bodeplot?") == 0)
   {
-    struct bode_plot_param_t *bplot_p = &bode_plot_param;
+    struct bode_plot_param_t *cloop_p = &pfc_cloop_bode_plot_param;
-    msg("bode plot param read from flash: b0=0x%08X, b1=0x%08X, b2=0x%08X, a1=0x%08X, a2=0x%08X\r\n",
+    struct bode_plot_param_t *vloop_p = &pfc_vloop_bode_plot_param;
-        bplot_p->b0,
+    print_bodeplot_params(cloop_p, vloop_p);
-        bplot_p->b1,
-        bplot_p->b2,
-        bplot_p->a1,
-        bplot_p->a2);
-    msg("bode plot param read from flash: b0=%d, b1=%d, b2=%d, a1=%d, a2=%d\r\n",
-        bplot_p->b0,
-        bplot_p->b1,
-        bplot_p->b2,
-        bplot_p->a1,
-        bplot_p->a2);
   }
   else if (strcmp(cmd_buf, "flash_bodeplot?") == 0)
   {
-    struct bode_plot_param_t tmp_bplot;
+    peek_bodeplot_params_in_flash(FLASH_PROG_ADDR_USER_CALI);
-    bode_plot_param_read_from_flash(&tmp_bplot, FLASH_PROG_ADDR_USER_CALI);
+  }
+  else if (cmd_match_with_arg(cmd_buf, "notify_en=", &arg))
+  {
+    int notify_en = atoi(arg);
+
+    if (notify_en == 1)
+    {
+      capture_start();
+      capture_continuous_mode = 0;
+    }
+    else if (notify_en == 0)
+    {
+      capture_continuous_mode = 0;
+      capture_package_cnt = 0;
+    }
+    else if (notify_en == 255)
+    {
+      const char *comma = strchr(arg, ',');
+      if (comma)
+      {
+        capture_package_cnt = atoi(comma + 1); // 連續模式下每次捕獲 n 包數據
+        capture_continuous_mode = 1;
+      }
+      else
+      {
+        msg("invalid notify_en format, use: notify_en=0 or notify_en=1 or notify_en=255,n\r\n");
+      }
+    }
+    else
+    {
+      msg("invalid notify_en format, use: notify_en=0 or notify_en=1 or notify_en=255,n\r\n");
+    }
+  }
+  else if (cmd_match_with_arg(cmd_buf, "notify_packet_gap=", &arg))
+  {
+    capture_packet_gap_ms = atoi(arg) < 10 ? 10 : atoi(arg); // 設置最小間隔為10ms
   }
   else
   {
@@ -296,59 +338,87 @@ static void dump_flash_bytes_8perline(uint32_t addr, uint32_t size)
 }
 #endif
 
-static int bode_plot_param_write_to_flash(const struct bode_plot_param_t *param, uint32_t addr)
+int write_bodeplot_params_to_flash(const struct bode_plot_param_t *cloop, const struct bode_plot_param_t *vloop, uint32_t addr)
 {
   int rval = 0;
-  uint32_t word_data[5] = { 0 };
 
-  if (!param)
+  if (!cloop || !vloop)
     return -1;
 
-  /* FLASH_ProgData requires 4-byte aligned length, so pad the last halfword. */
+  struct flash_bode_plot_blob_t blob = {
-  word_data[0] = param->b0;
+    .magic = FLASH_PARAM_MAGIC,
-  word_data[1] = param->b1;
+    .cloop = *cloop,
-  word_data[2] = param->b2;
+    .vloop = *vloop,
-  word_data[3] = param->a1;
+    .reserved = 0,
-  word_data[4] = param->a2;
+  };
 
   rval = FLASH_ErasePage(addr);
   if (rval)
   {
-    err(" ! erase plot param fail (%d)\n", rval);
+    err(" ! erase plot/vloop param fail (%d)\n", rval);
     return rval;
   }
 
-  rval = FLASH_ProgData(addr, word_data, sizeof(word_data));
+  rval = FLASH_ProgData(addr, (uint32_t *)&blob, sizeof(blob));
   if (rval)
   {
-    err(" ! prog plot param fail (%d)\n", rval);
+    err(" ! prog plot/vloop param fail (%d)\n", rval);
     return rval;
   }
 
   return 0;
 }
 
-void bode_plot_param_read_from_flash(struct bode_plot_param_t *param, uint32_t addr)
+void peek_bodeplot_params_in_flash(uint32_t addr)
 {
-  const void *flash_ptr = (const void *)addr;
+  struct flash_bode_plot_blob_t blob = { 0 };
 
-  if (!param)
+  memcpy(&blob, (const void *)addr, sizeof(blob));
+
+  if (blob.magic != FLASH_PARAM_MAGIC)
+  {
+    err(" ! invalid flash blob magic: 0x%08X\n", blob.magic);
+    return;
+  }
+
+  msg("flash blob content:\r\n");
+  msg("  magic: 0x%08X\r\n", blob.magic);
+  print_bodeplot_params(&blob.cloop, &blob.vloop);
+}
+
+void read_bodeplot_params_from_flash(struct bode_plot_param_t *cloop, struct bode_plot_param_t *vloop, uint32_t addr)
+{
+  struct flash_bode_plot_blob_t blob = { 0 };
+
+  if (!cloop || !vloop)
     return;
 
-  memcpy(param, flash_ptr, sizeof(*param));
+  memcpy(&blob, (const void *)addr, sizeof(blob));
 
-  msg("bode plot param read from flash: b0=0x%08X, b1=0x%08X, b2=0x%08X, a1=0x%08X, a2=0x%08X\r\n",
+  if (blob.magic != FLASH_PARAM_MAGIC)
-      param->b0,
+  {
-      param->b1,
+    err(" ! invalid flash blob magic: 0x%08X\n", blob.magic);
-      param->b2,
+    return;
-      param->a1,
+  }
-      param->a2);
+
-  msg("bode plot param read from flash: b0=%d, b1=%d, b2=%d, a1=%d, a2=%d\r\n",
+  *cloop = blob.cloop;
-      param->b0,
+  *vloop = blob.vloop;
-      param->b1,
+}
-      param->b2,
+
-      param->a1,
+void print_bodeplot_params(struct bode_plot_param_t *cloop, struct bode_plot_param_t *vloop)
-      param->a2);
+{
+  msg("cloop: b0=%d, b1=%d, b2=%d, a1=%d, a2=%d\r\n",
+      cloop->b0,
+      cloop->b1,
+      cloop->b2,
+      cloop->a1,
+      cloop->a2);
+  msg("vloop: b0=%d, b1=%d, b2=%d, a1=%d, a2=%d\r\n\n",
+      vloop->b0,
+      vloop->b1,
+      vloop->b2,
+      vloop->a1,
+      vloop->a2);
 }
 
 /* main code*/
@@ -358,16 +428,37 @@ void app(void)
 
   sysclk_systick_init(SYSCFG_ClkSrc_HSI, SYS_TICK_1_MS);
 
-  sys_disable_ice();
+  // sys_disable_ice();
 
   uart_init();
 
   info("This is a app demo project\n");
   info("uart cmd demo\n");
 
+  struct bode_plot_param_t *cloop_p = &pfc_cloop_bode_plot_param;
+  struct bode_plot_param_t *vloop_p = &pfc_vloop_bode_plot_param;
+
+  // cloop_p->b0 = 1021;
+  // cloop_p->b1 = -480;
+  // cloop_p->b2 = -522;
+  // cloop_p->a1 = -1951;
+  // cloop_p->a2 = -14414;
+
+  // vloop_p->b0 = 598;
+  // vloop_p->b1 = -64;
+  // vloop_p->b2 = -408;
+  // vloop_p->a1 = -12644;
+  // vloop_p->a2 = -3615;
+
+  // write plot param to flash
+  // msg("write plot param to flash\r\n");
+  // write_bodeplot_params_to_flash(cloop_p, vloop_p, FLASH_PROG_ADDR_USER_CALI);
+  // print_bodeplot_params(cloop_p, vloop_p);
+
   // read plot param from flash
-  struct bode_plot_param_t *bplot_p = &bode_plot_param;
+  msg("read plot param from flash\r\n");
-  bode_plot_param_read_from_flash(bplot_p, FLASH_PROG_ADDR_USER_CALI);
+  read_bodeplot_params_from_flash(cloop_p, vloop_p, FLASH_PROG_ADDR_USER_CALI);
+  print_bodeplot_params(cloop_p, vloop_p);
 
   while (1)
   {

pec930_sdk-v1.0.1/Examples/template/PFC_LLC_2026-05-20_2P2Z_ok/src/init.c

@@ -1,19 +1,14 @@
-/*
+/**
- * init.c
+ * Copyright (c) 2026 Wisetop. All Rights Reserved.
- *
- *  Created on: 2025年8月18日
- *      Author: jim_liao
  */
 
 #include "init.h"
 #include "app.h"
 #include "hal_device.h"
-#include "isr.h"
 
 //=============================================================================
 //                  Constant Definition
 //=============================================================================
-// #define CONFIG_OPA_PGA_GAIN     OPAMP_PGAGain_1 //OPAMP_PGAGain_5
 
 //=============================================================================
 //                  Public Function Definition
@@ -62,23 +57,210 @@ _Post_Proc(PWR_ModeTypeDef pwr_mode)
     return;
 }
 #endif
-//========================================================================
+//===================================================================================
-void SYS_Config()
+void gpio_init(void)
 {
-  SYSCFG_ClkInitTypeDef SysClkInit = { 0 };
+  GPIO_InitTypeDef gpio_init = { 0 };
+
+  // PA12(vfb)(vcomp)
+  gpio_init.GPIO_Pin = GPIO_Pin_12;
+  gpio_init.GPIO_Mode = GPIO_Mode_IN;
+  gpio_init.GPIO_PuPd = GPIO_PuPd_NOPULL;
+  GPIO_Init(GPIOA, &gpio_init);
+
+  // PA15(button)
+  gpio_init.GPIO_Pin = GPIO_Pin_15;
+  gpio_init.GPIO_Mode = GPIO_Mode_IN;
+  gpio_init.GPIO_PuPd = GPIO_PuPd_UP;
+  GPIO_Init(GPIOA, &gpio_init);
+
+#if 0 // 取消了
+  // PA5(TP1)
+  // PA6(TP2)
+  gpio_init.GPIO_Pin = GPIO_Pin_05;
+  gpio_init.GPIO_Pin |= GPIO_Pin_06;
+  gpio_init.GPIO_Mode = GPIO_Mode_OUT;
+  GPIO_Init(GPIOA, &gpio_init);
+#endif
+}
+//===================================================================================
+void opa_init(void)
+{
+  // gpio
+  GPIO_InitTypeDef gpio_init = { 0 };
+  gpio_init.GPIO_Pin = GPIO_Pin_07 | GPIO_Pin_08; // Pin_09 is set as power_ok
+  gpio_init.GPIO_Mode = GPIO_Mode_ANAL;
+  gpio_init.GPIO_PuPd = GPIO_PuPd_NOPULL;
+  GPIO_Init(GPIOA, &gpio_init);
+
+  // opa
+  OPAMP_InitTypeDef opa_init = { 0 };
+  opa_init.OPAMP_VinP = OPAMP_VinP_IO;    // PA8
+  opa_init.OPAMP_VinM = OPAMP_VinM_GND;   // internal GND, PIN 留給 POWER_OK
+  opa_init.OPAMP_Vout = OPAMP_Vout_IO;    // PA7, 拉到 IO PA7，需要外部 500 ~ 1000pF 電容
+  opa_init.OPAMP_Gain = OPAMP_PGAGain_15; // x1~x16 as needed, 使用 15 倍, 減少 RS 功耗
+  OPAMP_Init(OPAMP0, &opa_init);
+  OPAMP_Enable(OPAMP0);
+}
+//===================================================================================
+void adc_init(void)
+{
+  // gpio
+  GPIO_InitTypeDef gpio_init;
+  gpio_init.GPIO_Pin = GPIO_Pin_10;  // vbus = PA10(AIN4)
+  gpio_init.GPIO_Pin |= GPIO_Pin_07; // iac = PA7(AIN9)
+  gpio_init.GPIO_Pin |= GPIO_Pin_13; // vac = PA13(AIN7)
+  gpio_init.GPIO_Pin |= GPIO_Pin_11; // vcr = PA11(AIN5)
+  gpio_init.GPIO_Mode = GPIO_Mode_ANAL;
+  GPIO_Init(GPIOA, &gpio_init);
+
+  // adc
+  ADC_InitTypeDef adc_init = { 0 };
+  ADC_StructInit(&adc_init);
+  adc_init.SelChannels = ADC_Channel_04;
+  adc_init.SelChannels |= ADC_Channel_09; // 量測外部 PA7
+  // adc_init.SelChannels |= ADC_Channel_00; // 若是讀取 PGA0 輸出的 AIN0 通道, 要改成 ADC_Channel_00
+  adc_init.SelChannels |= ADC_Channel_07;
+  adc_init.SelChannels |= ADC_Channel_05;
+  adc_init.ClkPrescaler = ADC_ClkDiv_4; // 60M/4 = 15MHz, ADC max working clock is 16MHz
+  adc_init.DataAlign = ADC_DataAlign_Right;
+  adc_init.Mode = ADC_Mode_Scan; // Scan mode
+  ADC_Init(ADC0, &adc_init);
+  ADC_ExtTrigConfig(ADC0, ADC_ExtTrigSource_TIM0, ADC_ExtTrigMode_Enable); // tim0 trigger adc
+
+  // ADC interrupt config
+  sys_irq_attr_t irq_attr = {
+    .disable_vector = false,
+    .trig_mode = SYS_IRQ_TRIGGER_LEVEL,
+    .level = SYS_IRQ_LEVEL_H,
+    .priority = SYS_IRQ_PRIORITY_MIDDEN,
+  };
+  sys_register_IRQ(ADC0_IRQn, isr_adc_handle, &irq_attr);
+
+  ADC0->CON0_b.INT_EN = 1; // ADC interrupt enable
+}
+//===================================================================================
+void llc_pwm_init(void)
+{
+  // gpio
+  // PA0(EPWM0P), PA1(EPWM0N)
+  GPIO_InitTypeDef gpio_init = {
+    .GPIO_Pin = GPIO_Pin_00 | GPIO_Pin_01,
+    .GPIO_Mode = GPIO_Mode_AF,
+    .GPIO_AF_Mode = GPIO_AF_6,
+  };
+  GPIO_Init(GPIOA, &gpio_init);
+
+  // tim
+  TIM_TimeBaseInitTypeDef tim_init = {
+    .TIM_Prescaler = 0,
+    .TIM_CounterMode = TIM_CounterMode_Up,
+    .TIM_Period = LLC_PERIOD_SS,
+    .TIM_ClockDivision = TIM_CKD_Div1,
+    .TIM_RepetitionCounter = 0,
+  };
+  TIM_DeInit(EPWM);
+  TIM_TimeBaseInit(EPWM, &tim_init);
+
+  TIM_ARRPreloadConfig(EPWM, ENABLE);
+
+  // pwm
+  TIM_OCInitTypeDef pwm_init = {
+    .TIM_OCMode = TIM_OCMode_PWM1,
+    .TIM_OutputState = TIM_OutputState_Disable,
+    .TIM_OCPolarity = TIM_OCPolarity_High,
+    .TIM_OCIdleState = TIM_OCIdleState_Reset,
+    .TIM_OutputNState = TIM_OutputNState_Disable,
+    .TIM_OCNPolarity = TIM_OCPolarity_High,
+    .TIM_Pulse = 1,
+  };
+  TIM_OC1Init(EPWM, &pwm_init);
+  TIM_OC2Init(EPWM, &pwm_init);
+
+  { /* Automatic Output enable, Break, dead time and lock configuration */
+    TIM_BDTRInitTypeDef bdtr_init = { 0 };
+    bdtr_init.TIM_LOCKLevel = TIM_LockLevel_OFF;
+    bdtr_init.TIM_DeadTime = DEAD_TIME_VALUE;
+    TIM_BDTRConfig(EPWM, &bdtr_init);
+  }
+
+  TIM_Cmd(EPWM, ENABLE);
+  TIM_CtrlPWMOutputs(EPWM, ENABLE);
+  EPWM->CCMR1_OUTPUT_b.OC1PE = 1; // Output Compare 1 preload enable
+}
+//===================================================================================
+void pfc_pwm_init(void) // single PWM for PFC
+{
+  // gpio
+  // PA2(TIM2_CH1)
+  GPIO_InitTypeDef gpio_init = {
+    .GPIO_Pin = GPIO_Pin_02,
+    .GPIO_Mode = GPIO_Mode_AF,
+    .GPIO_AF_Mode = GPIO_AF_5,
+  };
+  GPIO_Init(GPIOA, &gpio_init);
+
+  // tim
+  TIM_TimeBaseInitTypeDef tim_init = {
+    .TIM_Prescaler = 0,
+    .TIM_CounterMode = TIM_CounterMode_Up,
+    .TIM_Period = PFC_PERIOD,
+    .TIM_ClockDivision = TIM_CKD_Div1,
+    .TIM_RepetitionCounter = 0,
+  };
+  TIM_DeInit(TIM2);
+  TIM_TimeBaseInit(TIM2, &tim_init);
+
+  TIM_ARRPreloadConfig(TIM2, ENABLE);
+
+  // pwm
+  TIM_OCInitTypeDef pwm_init = {
+    .TIM_OCMode = TIM_OCMode_PWM1,
+    .TIM_OutputState = TIM_OutputState_Disable,
+    .TIM_OCPolarity = TIM_OCPolarity_High,
+    .TIM_OCIdleState = TIM_OCIdleState_Reset,
+    .TIM_Pulse = 1,
+  };
+  TIM_OC1Init(TIM2, &pwm_init);
+
+  TIM_Cmd(TIM2, ENABLE);            // enable PWM
+  TIM_CtrlPWMOutputs(TIM2, ENABLE); // enable PWM output
+  TIM2->CCMR1_OUTPUT_b.OC1PE = 1;   // Output Compare 1 preload enable
+}
+
+//===================================================================================
+void tim0_init(void)
+{
+  LPTIM_InitTypeDef tim0_init = {
+    .LPTIM_Prescaler = 0,
+    .LPTIM_ClockSource = LPTIM_CLK_Src_SysClk,
+    .LPTIM_MatchMode = LPTIM_MatchMode_IRQ | LPTIM_MatchMode_Reset,
+    .LPTIM_MatchValue = TIM0_PERIOD,
+  };
+  LPTIM_Init(TIM0, &tim0_init);
+
+  LPTIM_Enable(TIM0);
+}
+//===================================================================================
+void sysclk_init(void)
+{
+  SYSCFG_ClkInitTypeDef SysClkInit = {
+    .ClkSource = SYSCFG_ClkSrc_HSI,
+  };
 
-  SysClkInit.ClkSource = SYSCFG_SYSCLKCR_CLKSW_HSI;
   SYSCFG_SysClkConfig(&SysClkInit);
-
   sys_config_systick(SYS_TICK_1_MS);
-
+}
+//===================================================================================
+void SYS_Config(void)
+{
+  sysclk_init();
   // PWR_EnterDeepSleepMode(_Pre_Proc, _Post_Proc); // use WDG wake up 1 sec
-
+  gpio_init();
-  gpio_config();
+  opa_init();
-  opa_config();
+  adc_init();
-  adc_config();
+  llc_pwm_init(); // 初始化但不輸出 EPWM_CH1
-  llc_pwm_config(); // 初始化但不輸出 EPWM_CH1
+  pfc_pwm_init(); // 初始化但不輸出 TIM2_CH1
-  pfc_pwm_config(); // 初始化但不輸出 TIM2_CH1
 
   __NOP();
   __NOP();
@@ -86,260 +268,6 @@ void SYS_Config()
   __NOP();
   __NOP(); // timer shift between pfc and tim0
 
-  tim0_config(); // trigger ADC, current loop frequency
+  tim0_init(); // trigger ADC, current loop frequency
   uart_init();
 }
-//===================================================================================
-void gpio_config()
-{
-  //-----------------//
-  //		OPA
-  //		IN+ = PA8
-  //		IN- = PA9
-  // 		OUT = PA7
-  //-----------------//
-
-  GPIO_InitTypeDef GPIO_InitStruct;
-
-#if 1
-  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_07 | GPIO_Pin_08; // Pin_09 is set as power_ok
-  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_ANAL;
-  GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL;
-  GPIO_Init(GPIOA, &GPIO_InitStruct);
-#endif
-
-#if 1
-  //-----------------//
-  //		PWM
-  //      LLC: PA0, PA1
-  //		PFC: PA2
-  //-----------------//
-  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_00 | GPIO_Pin_01;
-  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_AF;
-  GPIO_InitStruct.GPIO_AF_Mode = GPIO_AF_6; // AF6 = EPWM
-  GPIO_Init(GPIOA, &GPIO_InitStruct);
-
-  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_02;
-  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_AF;
-  GPIO_InitStruct.GPIO_AF_Mode = GPIO_AF_5; // AF5 = TIM2
-  GPIO_Init(GPIOA, &GPIO_InitStruct);
-
-  //-----------------//
-  //		ADC
-  //  PA7(iac), PA10(vbus), PA13(vac)  //  PA11(cr), PA12(vfb)-->GPIO
-  //-----------------//
-  GPIO_InitTypeDef GPIO_InitADC;
-  GPIO_InitADC.GPIO_Pin = GPIO_Pin_07 | GPIO_Pin_10 | GPIO_Pin_13; // | GPIO_Pin_11; // PA11(cr)
-  GPIO_InitADC.GPIO_Mode = GPIO_Mode_ANAL;
-  GPIO_Init(GPIOA, &GPIO_InitADC);
-
-  //-----------------//
-  //		Button
-  //-----------------//
-  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_15; // PA15
-  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_IN;
-  GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_UP; // pull up
-  GPIO_Init(GPIOA, &GPIO_InitStruct);
-
-  //-----------------//
-  //		FB (VCOMP)
-  //-----------------//
-  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_12; // PA12
-  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_IN;
-  GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL; // no pull
-  GPIO_Init(GPIOA, &GPIO_InitStruct);
-#endif
-
-#if 0 // 取消了
-	//-----------------//
-	//		test pin PA5: TP1, PA6: TP2
-	//-----------------//
-    GPIO_InitStruct.GPIO_Pin      = GPIO_Pin_05 | GPIO_Pin_06; // PA6 = TP2
-    GPIO_InitStruct.GPIO_Mode     = GPIO_Mode_OUT;
-    GPIO_Init(GPIOA, &GPIO_InitStruct);
-#endif
-}
-//===================================================================================
-void opa_config(void)
-{
-  OPAMP_InitTypeDef opa_init = { 0 };
-
-  opa_init.OPAMP_VinP = OPAMP_VinP_IO;
-  opa_init.OPAMP_VinM = OPAMP_VinM_GND;   // 設定內部 GND ，PIN 留給 POWER_OK
-  opa_init.OPAMP_Vout = OPAMP_Vout_IO;    // 拉到 IO，需要外部 500 ~ 1000pF 電容
-  opa_init.OPAMP_Gain = OPAMP_PGAGain_15; // 使用最大 15 倍，減少 RS 功耗
-
-  // 正向放大器 OK
-  // 電壓隨耦器 OK
-  // 反向放大器 NG
-  // V+ 接 1/2 VCC，差動放大器 OK
-
-  OPAMP_Init(OPAMP0, &opa_init);
-
-  OPAMP_Enable(OPAMP0);
-}
-//===================================================================================
-void adc_config(void)
-{
-  ADC_InitTypeDef init = { 0 };
-  ADC_StructInit(&init);
-
-  ADC_InitTypeDef init1 = { 0 };
-  ADC_StructInit(&init1);
-  // iac = 	PA7 	= ADC_Channel_09
-  // vac = 	PA13 	= ADC_Channel_07
-  // vbus = 	PA10 	= ADC_Channel_04
-  // ----------------------------------------------
-  // vcr = 	PA11 	= ADC_Channel_05 (未使用)
-  // vfb = 	PA12 	= ADC_Channel_06 (使用 GPIO)
-  init1.SelChannels = ADC_Channel_04 | ADC_Channel_07 | ADC_Channel_09 | ADC_Channel_05;
-  // init1.SelChannels    = ADC_Channel_09 ;// OP_O 指定到 PA7 時，ADC 需要用 CH_09 讀取
-  init1.ClkPrescaler = ADC_ClkDiv_4; // 60M/4 = 15M，接近 1MSPS (1us 轉換時間), 最快速度
-  init1.DataAlign = ADC_DataAlign_Right;
-  init1.Mode = ADC_Mode_Scan; // Scan mode
-  ADC_Init(ADC0, &init1);
-
-  // ADC_ExtTrigConfig(ADC0, ADC_ExtTrigSource_EPWM_CH2R, ADC_ExtTrigMode_Enable);
-  ADC_ExtTrigConfig(ADC0, ADC_ExtTrigSource_16, ADC_ExtTrigMode_Enable); // use tim0 trigger
-
-#if 1
-  { // Configure TIM interrupts
-    sys_irq_attr_t irq_attr = {
-      .disable_vector = false,
-    };
-
-    irq_attr.trig_mode = SYS_IRQ_TRIGGER_LEVEL;
-    irq_attr.level = SYS_IRQ_LEVEL_H;
-    irq_attr.priority = SYS_IRQ_PRIORITY_MIDDEN;
-    sys_register_IRQ(ADC0_IRQn, isr_adc_handle, &irq_attr);
-    ADC0->CON0_b.INT_EN = 1;
-  }
-#endif
-}
-//===================================================================================
-void llc_pwm_config() // complimentary PWM for LLC
-{
-  TIM_OCInitTypeDef TIM_OCInitStruct;
-  TIM_TimeBaseInitTypeDef TIM_TimeBaseInitStruct;
-
-  /*
-    {   // Configure TIM interrupts
-        sys_irq_attr_t      irq_attr = { .disable_vector = false, };
-
-        irq_attr.trig_mode      = SYS_IRQ_TRIGGER_LEVEL;
-        irq_attr.level          = SYS_IRQ_LEVEL_H;
-        irq_attr.priority       = SYS_IRQ_PRIORITY_MIDDEN;
-        sys_register_IRQ(EPWM_IRQn, isr_epwm_handle, &irq_attr);
-    }
-  */
-  TIM_DeInit(EPWM);
-
-  TIM_TimeBaseStructInit(&TIM_TimeBaseInitStruct);
-  TIM_TimeBaseInitStruct.TIM_Prescaler = 0;
-  TIM_TimeBaseInitStruct.TIM_CounterMode = TIM_CounterMode_Up;
-  TIM_TimeBaseInitStruct.TIM_Period = LLC_PERIOD_SS;
-  TIM_TimeBaseInitStruct.TIM_ClockDivision = TIM_CKD_Div1;
-  TIM_TimeBaseInitStruct.TIM_RepetitionCounter = 0;
-  TIM_TimeBaseInit(EPWM, &TIM_TimeBaseInitStruct);
-
-  TIM_ARRPreloadConfig(EPWM, ENABLE);
-
-  TIM_OCStructInit(&TIM_OCInitStruct);
-  TIM_OCInitStruct.TIM_OCMode = TIM_OCMode_PWM1;
-  TIM_OCInitStruct.TIM_OutputState = TIM_OutputState_Disable;
-  TIM_OCInitStruct.TIM_Pulse = 0;
-  TIM_OCInitStruct.TIM_OCPolarity = TIM_OCPolarity_High;
-  TIM_OCInitStruct.TIM_OCIdleState = TIM_OCIdleState_Reset;
-  TIM_OCInitStruct.TIM_Pulse = 1;
-
-  TIM_OCInitStruct.TIM_OutputNState = TIM_OutputNState_Disable;
-  TIM_OCInitStruct.TIM_OCNPolarity = TIM_OCPolarity_High;
-  TIM_OC1Init(EPWM, &TIM_OCInitStruct);
-
-  TIM_OCInitStruct.TIM_Pulse = 1;
-  TIM_OC2Init(EPWM, &TIM_OCInitStruct);
-
-  { /* Automatic Output enable, Break, dead time and lock configuration */
-    TIM_BDTRInitTypeDef bdtr_init = { 0 };
-    bdtr_init.TIM_LOCKLevel = TIM_LockLevel_OFF;
-    bdtr_init.TIM_DeadTime = DEAD_TIME_VALUE;
-
-    TIM_BDTRConfig(EPWM, &bdtr_init);
-  }
-
-  // EPWM->DIER |= 0x1000;	// Underflow interrupt enable
-  //__enable_irq();
-  TIM_Cmd(EPWM, ENABLE);
-  TIM_CtrlPWMOutputs(EPWM, ENABLE);
-  EPWM->CCMR1_OUTPUT_b.OC1PE = 1; // Output Compare 1 preload enable
-
-  // EPWM->CCR1 = 300; // for test
-  // REG_SET_BITS(EPWM->CCER, TIM_CCER_CC1E_Msk | TIM_CCER_CC1NE_Msk); // 需要 SET 才會輸出
-}
-//===================================================================================
-void pfc_pwm_config() // single PWM for PFC
-{
-  TIM_OCInitTypeDef TIM_OCInitStruct;
-  TIM_TimeBaseInitTypeDef TIM_TimeBaseInitStruct;
-  /*
-    {   // Configure TIM interrupts
-        sys_irq_attr_t      irq_attr = { .disable_vector = false, };
-
-        irq_attr.trig_mode      = SYS_IRQ_TRIGGER_LEVEL;
-        irq_attr.level          = SYS_IRQ_LEVEL_H;
-        irq_attr.priority       = SYS_IRQ_PRIORITY_MIDDEN;
-        sys_register_IRQ(TIM2_IRQn, isr_tim2_handle, &irq_attr);
-    }
-  */
-
-  TIM_DeInit(TIM2);
-
-  TIM_TimeBaseStructInit(&TIM_TimeBaseInitStruct);
-  TIM_TimeBaseInitStruct.TIM_Prescaler = 0;
-  TIM_TimeBaseInitStruct.TIM_CounterMode = TIM_CounterMode_Up;
-  TIM_TimeBaseInitStruct.TIM_Period = PFC_PERIOD;
-  TIM_TimeBaseInitStruct.TIM_ClockDivision = TIM_CKD_Div1;
-  TIM_TimeBaseInitStruct.TIM_RepetitionCounter = 0;
-  TIM_TimeBaseInit(TIM2, &TIM_TimeBaseInitStruct);
-  TIM_ARRPreloadConfig(TIM2, ENABLE);
-
-  TIM_OCStructInit(&TIM_OCInitStruct);
-  TIM_OCInitStruct.TIM_OCMode = TIM_OCMode_PWM1;
-  TIM_OCInitStruct.TIM_OutputState = TIM_OutputState_Disable;
-  TIM_OCInitStruct.TIM_Pulse = 0;
-  TIM_OCInitStruct.TIM_OCPolarity = TIM_OCPolarity_High;
-  TIM_OCInitStruct.TIM_OCIdleState = TIM_OCIdleState_Reset;
-  TIM_OCInitStruct.TIM_Pulse = 1;
-  // TIM_OCInitStruct.TIM_OutputNState  = TIM_OutputNState_Disable; // no negative output
-  // TIM_OCInitStruct.TIM_OCNPolarity   = TIM_OCPolarity_High;
-  TIM_OC1Init(TIM2, &TIM_OCInitStruct);
-
-  // TIM2->DIER |= 0x1000;	// Underflow interrupt enable
-  //__enable_irq();
-  TIM_Cmd(TIM2, ENABLE);            // enable PWM
-  TIM_CtrlPWMOutputs(TIM2, ENABLE); // enable PWM output
-  TIM2->CCMR1_OUTPUT_b.OC1PE = 1;   // Output Compare 1 preload enable
-                                    // TIM2->CCR1 = 200; // for test
-  // REG_SET_BITS(TIM2->CCER, TIM_CCER_CC1E_Msk); // set bit enable output
-}
-
-//===================================================================================
-void tim0_config()
-{
-  LPTIM_InitTypeDef Init = { 0 };
-
-  Init.LPTIM_Prescaler = 0;
-  Init.LPTIM_ClockSource = LPTIM_CLK_Src_SysClk;
-  Init.LPTIM_MatchMode = LPTIM_MatchMode_IRQ | LPTIM_MatchMode_Reset; // | LPTIM_MatchMode_Stop;
-  Init.LPTIM_MatchValue = TIM0_PERIOD;
-  LPTIM_Init(TIM0, &Init);
-
-#if 0
-    sys_irq_attr_t      irq_attr = { .trig_mode = SYS_IRQ_TRIGGER_LEVEL, };
-    sys_register_IRQ(TIM0_IRQn, isr_tim0_handle, &irq_attr);
-    sys_enable_girq();
-    LPTIM_ITConfig(TIM0, true);
-#endif
-
-  LPTIM_Enable(TIM0);
-}

pec930_sdk-v1.0.1/Examples/template/PFC_LLC_2026-05-20_2P2Z_ok/src/isr.c

@@ -1,69 +0,0 @@
-/**
- * Copyright (c) 2024 Wei-Lun Hsu. All Rights Reserved.
- */
-/** @file isr.c
- *
- * @author Wei-Lun Hsu
- * @version 0.1
- * @date 2024/09/16
- * @license
- * @description
- */
-
-#include "isr.h"
-#include "init.h"
-
-//=============================================================================
-//                  Constant Definition
-//=============================================================================
-
-//=============================================================================
-//                  Macro Definition
-//=============================================================================
-
-//=============================================================================
-//                  Global Data Definition
-//=============================================================================
-// uint8_t volatile tim0_trigger = 0;
-// extern uint16_t iac;
-// extern uint16_t vac;
-// extern uint16_t vbus;
-// extern uint16_t vac_avg1, vac_avg2;
-// extern uint16_t vbus_avg;
-// extern uint8_t hi_line;
-//=============================================================================
-//                  Private Function Definition
-//=============================================================================
-
-//=============================================================================
-//                  Public Function Definition
-//=============================================================================
-/*
-__INTERRUPT void isr_tim2_handle(void)
-{
-  if((TIM2->SR & 0x20000) == 0x20000) // UDIF: Underflow interrupt flag
-    {
-      TIM_ClearITPendingBit(TIM2, 0x20000);
-    }
-}
-*/
-//----------------------------------------------------------------------------------
-
-//----------------------------------------------------------------------------------
-#if 0
-__INTERRUPT void isr_tim0_handle(void)
-{
-	SAVE_IRQ_CSR_CONTEXT();
-
-    if( LPTIM_GetFlagStatus(TIM0, LPTIM_Flag_Match0) )
-    {
-        LPTIM_ClearFlag(TIM0, LPTIM_Flag_Match0);
-        tim0_trigger = 1;
-
-        GPIO_TogglePin(GPIOA, GPIO_Pin_05);
-    }
-
-    RESTORE_IRQ_CSR_CONTEXT();
-    return;
-}
-#endif

pec930_sdk-v1.0.1/Examples/template/PFC_LLC_2026-05-20_2P2Z_ok/src/main.c

@@ -2,22 +2,20 @@
 #include "main.h"
 #include "app.h"
 #include "init.h"
-#include "isr.h"
 //=============================================================================
 //                  Constant Definition
 //=============================================================================
-#define DATA_LOG       0
+#define CAPTURE_BUF_SIZE 160
-#define DATA_MONITOR   0
-#define DEBOUNCE_TIME  20
-#define BUF_SIZE       300 // > 300 記憶體不夠用(4組) > 700 記憶體不夠用(2組)
 
-#define CR_1P1Z_B0_Q14 6313
+#define DEBOUNCE_TIME    20
-#define CR_1P1Z_B1_Q14 -5113
+
-#define CR_1P1Z_A1_Q14 -5803
+#define CR_1P1Z_B0_Q14   6313
+#define CR_1P1Z_B1_Q14   -5113
+#define CR_1P1Z_A1_Q14   -5803
 // 前饋輸出限制（請根據您主環 Q14 格式的數值範圍調整）
 // 假設最大前饋量限制為實數值 50.0 -> 50.0 * 16384 = 819200
-#define CR_FF_MAX_Q14  1638400 //819200 // 50 duty << 14
+#define CR_FF_MAX_Q14    1638400  // 819200 // 50 duty << 14
-#define CR_FF_MIN_Q14  -1638400 //-819200
+#define CR_FF_MIN_Q14    -1638400 //-819200
 
 //=============================================================================
 //                  Macro Definition
@@ -45,26 +43,36 @@ typedef enum
   STATE_PAUSE           // 暫停，測試用
 } SystemState_t;
 
+typedef struct
+{
+  // uint32_t timestamp;
+  uint16_t iac;
+  // uint16_t vac;
+  // uint16_t vbus;
+  // uint16_t vcr;
+} CaptureSample_t;
+
 //=============================================================================
 //                  Global Data Definition
 //=============================================================================
 
-// #define kp 		250
+/* PID 轉換 2P2Z係數*/
-// #define ki 		2
+// #define kp 250
-// #define kd 		0
+// #define ki 2
+// #define kd 0
 
-// #define ff_max 	8000
+// 2P2Z 係數（這些需要根據你的 PID 增益與控制頻率重新計算或調試）
-
+// int32_t b0 = kp + ki + kd;  // 對應比例 + 部分積分/微分貢獻（可調整）
-// #define v_kp	10
+// int32_t b1 = -kp - kd - kd; // e[k-1] 係數（通常為正或負）
-#define v_ki 10
+// int32_t b2 = kd;            // e[k-2] 係數
-#define v_kd 0
+// int32_t a1 = 128;           // -A1（因為通常寫成 u[k] = ... + A1*u[k-1] + A2*u[k-2]，這裡 a1 = 128 代表 A1 ≈ 1）
+// int32_t a2 = 0;             // -A2（PID 特例時 a2 常為 0）
 
 SystemState_t sys_state = STATE_INIT;
 uint8_t is_zero_crossing = 0;
-uint8_t burst_mode_active = 0;
+static uint8_t last_is_zero_crossing = 0;
 uint8_t llc_running = 0;
 uint8_t pfc_running = 0;
-static uint8_t last_is_zero_crossing = 0;
 uint8_t is_brown_in = 0; // 0: 關機/保護中, 1: 正常工作
 static uint8_t cur_loop_fun_en = 0;
 
@@ -86,23 +94,9 @@ uint32_t vbus_ovp = (VBUS_OVP * 4096 / VBUS_2ADC / 3.3);
 uint32_t vbus_set = (VBUS_SET * 4096 / VBUS_2ADC / 3.3);
 uint32_t vbus_set_h = (VBUS_SET_H * 4096 / VBUS_2ADC / 3.3); // burst mode in
 uint32_t vbus_set_l = (VBUS_SET_L * 4096 / VBUS_2ADC / 3.3); // burst mode out
-// uint32_t vbus_set_h2 = (VBUS_SET_H2 * 4096 / VBUS_2ADC / 3.3);
-// uint32_t digi_vcomp_max = (uint32_t)(VBUS_SET_H * 4096 / VBUS_2ADC / 3.3) << DIGI_COMP_BIT;
 uint32_t digi_vcomp_max = (LLC_PERIOD_MAX - LLC_PERIOD_MIN) << LLC_COMP_GAIN_BIT;
-int32_t vbus_err = 0;
-int32_t vbus_err_prev = 0;
-int32_t vbus_comp = 0;
 int32_t vbus_comp2 = 0; // 過零點用
-int32_t vbus_comp_prev = 0;
-int32_t vbus_int = 0, vbus_por = 0;
-uint16_t pfc_duty = 0;
-uint8_t pfc_ss = 0;
-uint16_t pfc_ss_cnt = 0;
 uint16_t llc_ss_cnt = 0;
-// volatile int16_t iac_err_0, iac_err_1;
-// volatile uint16_t iac_set;
-// volatile int32_t iac_int, iac_por, iac_der;
-// volatile int16_t iac_comp = 0;
 //-----------------------------------------------
 KeyState_t key1State = KEY_IDLE;
 uint32_t key1Timer = 0;
@@ -110,95 +104,54 @@ uint8_t key1_action = 0;
 uint8_t keyInput;
 //-----------------------------------------------
 uint8_t power_on_cmd = 0;
-uint8_t temp_off = 0;
+uint32_t vac_avg1;
-uint16_t vbus_volt, vac_volt;
-int32_t tx_buf1[BUF_SIZE];
-int32_t tx_buf2[BUF_SIZE];
-// uint16_t tx_buf3[BUF_SIZE];
-// uint16_t tx_buf4[BUF_SIZE];
-uint16_t buf_idx = 0;
-uint8_t is_full = 0;
-uint16_t count_down = 2000; // for data log
-uint16_t i_ff;
-uint32_t vac_avg1, vac_avg2, vac_avg3;
 uint32_t vbus_avg = 0;
 uint32_t vcr_avg;
 static volatile uint16_t vac_pk1, vac_pk2;
-uint8_t hi_line = 0; // 0=110V, 1=220V
-uint8_t vbus_ready = 0;
-uint16_t hi_cnt, lo_cnt;
 uint32_t static digital_vcomp = (LLC_PERIOD_MAX - LLC_PERIOD_MIN) << LLC_COMP_GAIN_BIT;
-int16_t fb_enent;
 uint16_t llc_period_ss = LLC_SS_MIN;
 uint16_t llc_run_arr = LLC_PERIOD_MIN;
-uint16_t llc_arr_cmp = 0;
 uint8_t v_loop_cnt = 0;
 uint8_t v_loop_cnt2 = 0;
-uint16_t brownout_cnt = 0;
 
 uint8_t volatile tim0_trigger = 0;
 
 // 全局或靜態變數（需在函數外或 static 保留狀態）
-static int32_t iac_err_0 = 0;  // e[k]
 static int32_t iac_err_1 = 0;  // e[k-1]
 static int32_t iac_err_2 = 0;  // e[k-2]
-static int32_t iac_comp = 0;   // u[k]
 static int32_t iac_comp_1 = 0; // u[k-1]  (前一次輸出)
 static int32_t iac_comp_2 = 0; // u[k-2]  (前兩次輸出)
 
 static int32_t vbus_err_1 = 0;
 static int32_t vbus_comp_1 = 0;
 
-// 2P2Z 係數（這些需要根據你的 PID 增益與控制頻率重新計算或調試）
-// int32_t b0 = kp + ki + kd;     // 對應比例 + 部分積分/微分貢獻（可調整）
-// int32_t b1 = -kp - kd - kd;      // e[k-1] 係數（通常為正或負）
-// int32_t b2 = kd;      // e[k-2] 係數
-// int32_t a1 = 128;    // -A1（因為通常寫成 u[k] = ... + A1*u[k-1] + A2*u[k-2]，這裡 a1 = 128 代表 A1 ≈ 1）
-// int32_t a2 = 0;      // -A2（PID 特例時 a2 常為 0）
-
-// 電壓環 2p2z 係數
-// int32_t v_b0 = v_kp + v_ki + v_kd;
-// int32_t v_b1 = -v_kp - v_kd - v_kd;
-// int32_t v_b2 = v_kd;
-// int32_t v_a1 = 128;
-// int32_t v_a2 = 0;
-
 uint16_t updata_cnt = 0;
 
 int32_t vbus_comp_prev1, vbus_comp_prev2;
 int32_t vbus_err_prev1, vbus_err_prev2;
-//-----------------------------------------------
+
+static volatile uint8_t capture_active = 0;
+static volatile uint8_t capture_ready = 0;
+static volatile uint16_t capture_idx = 0;
+static CaptureSample_t capture_buf[CAPTURE_BUF_SIZE];
+uint8_t capture_continuous_mode = 0;
+int16_t capture_package_cnt = 5;
+uint16_t capture_packet_gap_ms = 1000;
 
 //=============================================================================
 //                  Private Function Definition
 //=============================================================================
 void A_Para_Reset()
 {
-  vbus_int = 0;
-  vbus_comp = 1000;
-  // iac_int = 0; iac_comp = 1000;
   digital_vcomp = (LLC_PERIOD_MAX - LLC_PERIOD_MIN) << LLC_COMP_GAIN_BIT;
   vbus_set = (VBUS_SET * 4096 / VBUS_2ADC / 3.3);
-  pfc_ss = 0;
-  pfc_ss_cnt = 0;
   v_loop_cnt = 0;
-  temp_off = 0;
 
-  iac_err_0 = 0;
   iac_err_1 = 0;
   iac_err_2 = 0;
   iac_comp_1 = 0;
   iac_comp_2 = 0;
 
-  vbus_err = 0;
-  vbus_err_prev = 0;
-  vbus_err_prev1 = 0;
-  vbus_err_prev2 = 0;
-  vbus_comp_prev = 0;
-  vbus_comp_prev1 = 0;
-  vbus_comp_prev2 = 0;
-  // vbus_comp2 = 1000;
-
   // set default value
   TIM2->ARR = PFC_PERIOD;
   TIM2->CCR1 = PFC_DUTY_MIN; // min for ss
@@ -210,7 +163,6 @@ void A_Para_Reset()
 
   pfc_running = 0;
   llc_running = 0;
-  brownout_cnt = 0;
 }
 //------------------------------------------------------------------------------
 void Key1_Scan()
@@ -253,6 +205,60 @@ void Key1_Scan()
   }
 }
 //-------------------------------------------------------------------------
+void capture_start(void)
+{
+  capture_idx = 0;
+  capture_ready = 0;
+  capture_active = 1;
+  msg("capture start,size=%d\r\n", CAPTURE_BUF_SIZE);
+}
+//-------------------------------------------------------------------------
+static inline void Capture_Sample_ISR(void)
+{
+  if (!capture_active)
+    return;
+
+  uint16_t idx = capture_idx;
+  if (idx >= CAPTURE_BUF_SIZE)
+    return;
+
+  // capture_buf[idx].timestamp = sys_get_tick();
+  capture_buf[idx].iac = iac;
+  //  capture_buf[idx].vac = vac;
+  //  capture_buf[idx].vbus = vbus;
+  //  capture_buf[idx].vcr = vcr;
+
+  idx++;
+  capture_idx = idx;
+
+  if (idx >= CAPTURE_BUF_SIZE)
+  {
+    capture_active = 0;
+    capture_ready = 1;
+  }
+}
+//-------------------------------------------------------------------------
+static void Capture_Dump_IfReady(void)
+{
+  if (!capture_ready)
+    return;
+
+  for (uint16_t i = 0; i < CAPTURE_BUF_SIZE; i++)
+  {
+    msg("%d\r\n", capture_buf[i].iac);
+
+    // msg("%d,%d,%d,%d,%d\r\n",
+    //     capture_buf[i].timestamp,
+    //     capture_buf[i].iac,
+    //     capture_buf[i].vac,
+    //     capture_buf[i].vbus,
+    //     capture_buf[i].vcr);
+  }
+
+  capture_ready = 0;
+  msg("capture done,count=%d\r\n", CAPTURE_BUF_SIZE);
+}
+//-------------------------------------------------------------------------
 void Key_Action()
 {
   if (power_on_cmd == 0)
@@ -355,22 +361,22 @@ void Vol_Loop_PFC_1P1Z(void)
   int32_t vbus_err_n = (int32_t)vbus_set - (int32_t)vbus_avg;
 
   // --- 策略 A：動態增益調整 ---
-   int32_t b0 = 139;
+  int32_t b0 = 139;
-   int32_t b1 = -129;
+  int32_t b1 = -129;
 
   //  vloop_p->b0 = 139;
   //  vloop_p->b1 = -129;
   //  vloop_p->a1 = -16383;
-/*
+  /*
-  if (vbus_err_n > 40 || vbus_err_n < -40) // ~ 20V
+    if (vbus_err_n > 40 || vbus_err_n < -40) // ~ 20V
   {
     // 大誤差時（通常是剛啟動或大跳載），強化參數加快反應
-    //b0 = 250;
+      //b0 = 250;
-    //b1 = -249;
+      //b1 = -249;
-     //b0 = 180; // 稍微調降強增益的力道
+       //b0 = 180; // 稍微調降強增益的力道
-     //b1 = -178;
+       //b1 = -178;
-	 b0 = 500;
+     b0 = 500;
-	 b1 = -499;
+     b1 = -499;
   }
   // --- 策略 B：接近目標時微調零點 (抗過衝) ---
   else if (vbus_err_n < 20 && vbus_err_n > -20) // ~ 5V
@@ -379,7 +385,7 @@ void Vol_Loop_PFC_1P1Z(void)
     b0 = 120;
     b1 = -119; // 如果不能用浮點數，請維持 120 / -119，增加阻尼感
   }
-*/
+  */
   // 2. 差分方程計算
   int64_t acc = (int64_t)b0 * vbus_err_n;
   acc += (int64_t)b1 * vbus_err_1;
@@ -420,12 +426,12 @@ void Vol_Loop_PFC_1P1Z(void)
 
   // 5. 輸出 Duty >> 14
   if (sys_state == STATE_PFC_SOFT_START || sys_state == STATE_RUN_SKIP) // 緩啟動期間直接控制 DUTY
-	  TIM2->CCR1 = (vbus_comp_1 >> 14); // 0 ~ 540
+    TIM2->CCR1 = (vbus_comp_1 >> 14);                                   // 0 ~ 540
 
   // 6. 輸出 comp >> 9 (變大 32 倍) (MAX ~ 18000) (540*32=17280)差不多，>> 9 應該是對的
   // if (sys_state == STATE_RUN_NORMAL) // 正常工作時間輸出 COMP 值
   vbus_comp2 = (vbus_comp_1 >> 9) + (cr_feed_forward_output_q14 << 1); // 太大會直接 OVP
-  //vbus_comp2 = (vbus_comp_1 >> 9);
+  // vbus_comp2 = (vbus_comp_1 >> 9);
 }
 //=============================================================
 static void Vol_Loop_PFC_1P1Z_UI(void) // ZERO: 120HZ, POLE:0.1HZ, G:10
@@ -456,7 +462,7 @@ static void Vol_Loop_PFC_1P1Z_UI(void) // ZERO: 120HZ, POLE:0.1HZ, G:10
 
   // 5. 輸出 Duty >> 14
   if (sys_state == STATE_PFC_SOFT_START || sys_state == STATE_RUN_SKIP) // 緩啟動期間直接控制 DUTY
-	  TIM2->CCR1 = (vbus_comp_1 >> 14); // 0 ~ 540
+    TIM2->CCR1 = (vbus_comp_1 >> 14);                                   // 0 ~ 540
 
   // 6. 輸出 comp >> 9 (變大 32 倍) (MAX ~ 18000) (540*32=17280)差不多，>> 9 應該是對的
   // if (sys_state == STATE_RUN_NORMAL) // 正常工作時間輸出 COMP 值
@@ -486,11 +492,12 @@ __attribute__((always_inline)) static inline void Cur_Loop_PFC_2P2Z(void) // 優
 
   // 2. 2P2Z 運算 (Fixed-point Q14)
 #if 1
-  struct bode_plot_param_t *bplot_p = &bode_plot_param;
+  struct bode_plot_param_t *cloop_p = &pfc_cloop_bode_plot_param;
-  int64_t acc1 = ((int64_t)bplot_p->b0 * local_iac_err_0) + ((int64_t)bplot_p->b1 * iac_err_1) + ((int64_t)bplot_p->b2 * iac_err_2);
 
-  int64_t acc2 = -((int64_t)bplot_p->a1 * iac_comp_1);
+  int64_t acc1 = ((int64_t)cloop_p->b0 * local_iac_err_0) + ((int64_t)cloop_p->b1 * iac_err_1) + ((int64_t)cloop_p->b2 * iac_err_2);
-  acc2 -= ((int64_t)bplot_p->a2 * iac_comp_2);
+
+  int64_t acc2 = -((int64_t)cloop_p->a1 * iac_comp_1);
+  acc2 -= ((int64_t)cloop_p->a2 * iac_comp_2);
 #endif
 
   acc1 += acc2;
@@ -528,28 +535,6 @@ __attribute__((always_inline)) static inline void Cur_Loop_PFC_2P2Z(void) // 優
   else if (local_duty < PFC_DUTY_MIN)
     local_duty = PFC_DUTY_MIN; // MIN = 12
   TIM2->CCR1 = local_duty;
-
-//  -------------------------------------------
-// 5. data log
-#if DATA_LOG
-  count_down--;
-  if (count_down < 1000)
-  {
-    tx_buf1[buf_idx] = local_iac_err_0; // y[n]
-    tx_buf2[buf_idx] = acc;             // x[n]
-    // tx_buf3[buf_idx] = local_iac_err_0;
-    // tx_buf4[buf_idx] = local_duty;
-    buf_idx++;
-  }
-
-  if (buf_idx >= (BUF_SIZE - 1))
-  {
-    is_full = 1;
-    pfc_pwm_disable();
-    sys_state = STATE_PAUSE;
-  }
-#endif
-  // -------------------------------------------
 }
 //============================================================================
 
@@ -636,6 +621,13 @@ __INTERRUPT void isr_adc_handle(void)
 
   if (cur_loop_fun_en) Cur_Loop_PFC_2P2Z(); // current loop
 
+  static uint8_t cnt = 0;
+  if (cnt++ >= 10)
+  {
+    Capture_Sample_ISR();
+    cnt = 0;
+  }
+
   // GPIO_ResetBits(GPIOA, GPIO_Pin_06);
 
   RESTORE_IRQ_CSR_CONTEXT();
@@ -644,46 +636,13 @@ __INTERRUPT void isr_adc_handle(void)
 //============================================================================
 void reset_pid_parameters(void)
 {
-  vbus_int = 0;
-  vbus_comp = 1000;
-
-  iac_err_0 = 0;
   iac_err_1 = 0;
   iac_err_2 = 0;
-  iac_comp = 0;
   iac_comp_1 = 0;
   iac_comp_2 = 0;
 
   digital_vcomp = (LLC_PERIOD_MAX - LLC_PERIOD_MIN) << LLC_COMP_GAIN_BIT;
 }
-//==============================================================================
-void Handle_UART_Monitor(void)
-{
-  static uint32_t msg_timer = 0;
-  if (sys_get_tick() - msg_timer >= 1000) // msg_out = 1, print
-  {
-    printf("%d\r\n", vac);
-    // printf("%d %d %d %d %d %d", power_on_cmd, sys_state, vbus_comp2, print1, print2, print3);
-    //msg("%d %d %d", power_on_cmd, sys_state, vac_pk2);
-    //msg("%d %d %d", iac, vac, vbus);
-    // 電壓環輸出最大 COMP，但是電流環輸出最小 DUTY
-    msg_timer = sys_get_tick();
-  }
-  // iac 零點大約 3640 ~ 3680
-}
-//================================================================================
-void Handle_UART_Log(void)
-{
-  for (int i = 0; i < BUF_SIZE; i++)
-  {
-    // printf("%d:%d:%d:%d\r\n", tx_buf1[i], tx_buf2[i], tx_buf3[i], tx_buf4[i]);
-    printf("%d:%d\r\n", tx_buf1[i], tx_buf2[i]);
-    // printf("%d\r\n", tx_buf1[i]);
-    sys_delay(5);
-  }
-  is_full = 0; // [重要] 列印完務必清除旗標，否則會死循環
-  buf_idx = 0; // 重置索引
-}
 //================================================================================
 void Vac_Peak_Detector(void)
 {
@@ -744,64 +703,57 @@ static void uart_rx_task(void)
   msg("RX: %s\r\n", cmd_buf);
   uart_cmd_parse(cmd_buf, sizeof(cmd_buf));
 }
+
+static void capture_continuous_task(void)
+{
+  static uint32_t msg_timer = 0;
+
+  if (capture_continuous_mode == 1 && capture_package_cnt > 0)
+  {
+    if (sys_get_tick() - msg_timer >= capture_packet_gap_ms)
+    {
+      capture_start();
+      msg_timer = sys_get_tick();
+      if (capture_package_cnt-- <= 0)
+      {
+        capture_continuous_mode = 0;
+        capture_package_cnt = 0;
+      }
+    }
+  }
+}
 //=============================================================================
 //                  Public Function Definition
 //=============================================================================
 int main(void)
 {
-  struct bode_plot_param_t *bplot_p = &bode_plot_param;
+  struct bode_plot_param_t *cloop_p = &pfc_cloop_bode_plot_param;
   struct bode_plot_param_t *vloop_p = &pfc_vloop_bode_plot_param;
 
   // 基礎硬體底層設定 (HIRC 60MHz, GPIO, ADC 採樣率 1Msps) [cite: 55, 127, 184]
   SYS_Config();
 
-  //pfc_set_duty(15);
+  // read plot param from flash
-  //pfc_pwm_enable();
+  msg("read plot param from flash\r\n");
-  //while(1);
+  read_bodeplot_params_from_flash(cloop_p, vloop_p, FLASH_PROG_ADDR_USER_CALI);
-
+  print_bodeplot_params(cloop_p, vloop_p);
-  //llc_set_period(600);
-  //llc_pwm_enable();
-  //while(1);
-
-  /*
-  while(1)
-  {
-	  Handle_UART_Monitor();
-  }
-   */
-
-  // PFC 電流環參數
-  bode_plot_param_read_from_flash(bplot_p, FLASH_PROG_ADDR_USER_CALI);
-
-  /*********************************************************************/
-  /* PFC 電壓環參數*/
-  //  vloop_p->a2 = 0;
-  //  vloop_p->b2 = 0;
-
-  //  // 120HZ, 0.1Hz, 100G
-  //  vloop_p->b0 = 139;
-  //  vloop_p->b1 = -129;
-  //  vloop_p->a1 = -16383;
-  /*********************************************************************/
-  /* PFC 電流環參數*/
-  //bplot_p->b0 = 3353681;
-  //bplot_p->b1 = -1577632;
-  //bplot_p->b2 = -1712512;
-  //bplot_p->a1 = -20921;
-  //bplot_p->a2 = 4545;
-  /*********************************************************************/
 
 #if 0 // 單測 PFC 電壓環 (OK)
-      /* PFC 電壓環參數*/
-  {
-    vloop_p->a2 = 0;
-    vloop_p->b2 = 0;
 
-    // 120HZ, 0.1Hz, 100G
+  // Not used
-    vloop_p->b0 = 139;
+  cloop_p->b0 = 0;
-    vloop_p->b1 = -129;
+  cloop_p->b1 = 0;
-    vloop_p->a1 = -16383;
+  cloop_p->b2 = 0;
-  }
+  cloop_p->a1 = 0;
+  cloop_p->a2 = 0;
+  
+  // 1P1Z 參數: Z=120HZ, P=0.1HZ, G=100 ?
+  vloop_p->b0 = 139;
+  vloop_p->b1 = -129;
+  vloop_p->b2 = 0;
+  vloop_p->a1 = -16383;
+  vloop_p->a2 = 0;
+  print_bodeplot_params(cloop_p, vloop_p);
 
   cur_loop_fun_en = 0; // 關閉電流環，專測電壓環
   sys_state = STATE_PFC_SOFT_START;
@@ -840,19 +792,25 @@ int main(void)
 
     Key1_Scan();
 
-    //Handle_UART_Monitor();
-
   }
 #endif
 
 #if 0 // 單測 PFC 電流環 (OK)
-      /* PFC 電流環參數*/
+
-      // Z1=200, Z2=1000000, P1=10, P2=20000, G=10000
+  // 2P2Z 參數: Z1=200, Z2=100000, P1=10, P2=20000, G=10000, fs=100K, bQ14, aQ14
-  bplot_p->b0 = 3353681;
+  cloop_p->b0 = 3353681;
-  bplot_p->b1 = -1577632;
+  cloop_p->b1 = -1577632;
-  bplot_p->b2 = -1712512;
+  cloop_p->b2 = -1712512;
-  bplot_p->a1 = -20114;
+  cloop_p->a1 = -20114;
-  bplot_p->a2 = 3737;
+  cloop_p->a2 = 3737;
+  
+  // Not used
+  vloop_p->b0 = 0;
+  vloop_p->b1 = 0;
+  vloop_p->b2 = 0;
+  vloop_p->a1 = 0;
+  vloop_p->a2 = 0;
+  print_bodeplot_params(cloop_p, vloop_p);
 
   cur_loop_fun_en = 1; // 開啟電流環，專測電流環
   while (1)
@@ -907,97 +865,94 @@ int main(void)
 #endif
 
 #if 0 // 測試 PFC 電壓環 + 電流環 (OK)
-	TIM2->CCR1 = 12; // min duty
+  TIM2->CCR1 = 12; // min duty
-	sys_state = STATE_PFC_SOFT_START;
+  sys_state = STATE_PFC_SOFT_START;
 
-	cur_loop_fun_en = 0; // 一開始關閉電流環，專測電流環
+  cur_loop_fun_en = 0; // 一開始關閉電流環，STATE_RUN_NORMAL再開電流環
-	  {
-	    vloop_p->a2 = 0;
-	    vloop_p->b2 = 0;
 
-	    // 120HZ, 0.1Hz, 100G
+  // 2P2Z 參數: Z1=200, Z2=100000, P1=10, P2=20000, G=10000, fs=100K, bQ14, aQ14
-	    vloop_p->b0 = 139;
+    	  cloop_p->b0 = 3353681;
-	    vloop_p->b1 = -129;
+    	  cloop_p->b1 = -1577632;
-	    vloop_p->a1 = -16383;
+    	  cloop_p->b2 = -1712512;
-	  }
+    	  cloop_p->a1 = -20114;
-      {
+    	  cloop_p->a2 = 3737;
-    	  bplot_p->b0 = 3353681;
-    	  bplot_p->b1 = -1577632;
-    	  bplot_p->b2 = -1712512;
-    	  bplot_p->a1 = -20114;
-    	  bplot_p->a2 = 3737;
-      }
 
-	while(1)
+  // 1P1Z 參數: Z=120HZ, P=0.1HZ, G=100 ?
+  vloop_p->b0 = 139;
+  vloop_p->b1 = -129;
+  vloop_p->b2 = 0;
+  vloop_p->a1 = -16383;
+  vloop_p->a2 = 0;
+
+  while (1)
+  {
+    if (tim0_trigger == 1) // 100KHZ
     {
-	    if (tim0_trigger == 1) // 100KHZ
+      tim0_trigger = 0;
-		{
+      // --- 1. 高速信號濾波 (簡易位移算法減少算力消耗) ---
-			tim0_trigger = 0;
-		    // --- 1. 高速信號濾波 (簡易位移算法減少算力消耗) ---
 			vac_avg1 = (vac_avg1 - (vac_avg1 >> 3)) + (vac >> 3);	// for current loop
     		vbus_avg = (vbus_avg - (vbus_avg >> 4)) + (vbus >> 4);	// for voltage loop
     		if (vbus > vbus_ovp) Power_Off(); // ovp
 
-    		Vac_Peak_Detector();
+      Vac_Peak_Detector();
 
-    		if (power_on_cmd == 1)
+      if (power_on_cmd == 1)
-    		{
+      {
-    			if (sys_state == STATE_PFC_SOFT_START)
+        if (sys_state == STATE_PFC_SOFT_START)
-    			{
+        {
     				if (pfc_running == 0) {
-    					pfc_pwm_enable();
+            pfc_pwm_enable();
-    					pfc_running = 1;
+            pfc_running = 1;
-    				}
+          }
 
-    				if (++v_loop_cnt >= 10) // 10KHZ
+          if (++v_loop_cnt >= 10) // 10KHZ
-    				{
+          {
     					Vol_Loop_PFC_1P1Z_UI();
     					//Vol_Loop_PFC_1P1Z();
-    					v_loop_cnt = 0;
+            v_loop_cnt = 0;
-    				}
+          }
 
-    				if (vbus_avg > vbus_set_l && is_zero_crossing == 1)
+          if (vbus_avg > vbus_set_l && is_zero_crossing == 1)
-    				{
+          {
-    					sys_state = STATE_RUN_NORMAL;
+            sys_state = STATE_RUN_NORMAL;
-    					// --- 關鍵修正：重新初始化電壓環內部狀態 ---
+            // --- 關鍵修正：重新初始化電壓環內部狀態 ---
-    					// 給予一個極小的初始 COMP 值，讓它從輕載慢慢往上爬
+            // 給予一個極小的初始 COMP 值，讓它從輕載慢慢往上爬
     					vbus_comp_1 = (10 << 14); // 假設從一個極小的係數開始
     					vbus_err_1 = 0;           // 清除誤差歷史
-    					vbus_comp2 = (vbus_comp_1 >> 9); // 讓電流環拿到的初始值是 10
+            vbus_comp2 = (vbus_comp_1 >> 9); // 讓電流環拿到的初始值是 10
     					cur_loop_fun_en = 1; // 開啟電流環
-    				}
+          }
-    			}
+        }
 
-    			else if (sys_state == STATE_RUN_NORMAL)
+        else if (sys_state == STATE_RUN_NORMAL)
-    			{
+        {
     				if (pfc_running == 0) {
-    					pfc_pwm_enable();
+            pfc_pwm_enable();
-    					pfc_running = 1;
+            pfc_running = 1;
-    				}
+          }
 
-    				if (++v_loop_cnt >= 10) // 10KHZ
+          if (++v_loop_cnt >= 10) // 10KHZ
-    				{
+          {
     					Vol_Loop_PFC_1P1Z_UI();
     					//Vol_Loop_PFC_1P1Z();
-    					v_loop_cnt = 0;
+            v_loop_cnt = 0;
-    				}
+          }
-    			}
+        }
-    		}
+      }
-		}
-	    Key1_Scan();
-	    //Handle_UART_Monitor();
     }
+    Key1_Scan();
+  }
 #endif
 
   // main loop
 
   /* PFC 電流環參數*/
   // Z1=200, Z2=100000, P1=10, P2=20000, G=8000
-    bplot_p->b0 = 3353681;
+  cloop_p->b0 = 3353681;
-    bplot_p->b1 = -1577632;
+  cloop_p->b1 = -1577632;
-    bplot_p->b2 = -1712512;
+  cloop_p->b2 = -1712512;
-    bplot_p->a1 = -20114;
+  cloop_p->a1 = -20114;
-    bplot_p->a2 = 3737;
+  cloop_p->a2 = 3737;
 
   cur_loop_fun_en = 1; // 開啟電流環，專測電流環
   while (1)
@@ -1070,7 +1025,7 @@ int main(void)
           if (++v_loop_cnt >= 10) // 10KHZ
           {
             Vol_Loop_PFC_1P1Z();
-            //Vol_Loop_PFC_1P1Z();
+            // Vol_Loop_PFC_1P1Z();
             v_loop_cnt = 0;
           }
 
@@ -1129,20 +1084,18 @@ int main(void)
           if (++v_loop_cnt >= 10)
           {
             // 先算前饋，再算主環，最後疊加
-            Load_Loop_1P1Z(); // Cr 前饋
+            Load_Loop_1P1Z();    // Cr 前饋
             Vol_Loop_PFC_1P1Z(); // PFC 電壓環
-            //Vol_Loop_LLC(); // LLC 電壓環
+            // Vol_Loop_LLC(); // LLC 電壓環
             v_loop_cnt = 0;
           }
 
-
           if (++v_loop_cnt2 >= 5) // 好一點
           {
             Vol_Loop_LLC(); // LLC 電壓環
             v_loop_cnt2 = 0;
           }
 
-
           break;
 
         case STATE_RUN_SKIP: // 5
@@ -1166,14 +1119,9 @@ int main(void)
     // --- 3. 非即時任務 (UI、通訊、Data Log) ---
     Key1_Scan();
 
-#if DATA_LOG
+    Capture_Dump_IfReady();
-    if (is_full == 1) Handle_UART_Log(); // 利用 PEC930 UART 輸出數據 [cite: 105, 336]
-#endif
-
-#if DATA_MONITOR
-    Handle_UART_Monitor();
-#endif
 
+    capture_continuous_task();
   } // while --------------------------------------------------------------------
 
   return 0;